Lele Ren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Lele Ren has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Jian Wang
5 shared publicationsShijie Zhao
5 shared publicationsFeihu Zhang
4 shared publicationsRuiqing Xie
China Academy of Engineering Physics, Mianyang, Sichuan, China
4 shared publications- Defeng Liao
Harbin Institute of Technology, Harbin, Heilongjiang, China
3 shared publications Defeng Liao
2 shared publications
Latest Publications
- Open Access
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 782 (2)
The Role of Pad Block’s Support Surface Topography in the Measurement of Optical Glass BK7’s Surface Figure
Large flat transmission mirrors made from optical glass BK7 are widely used in the high-power laser facility, which are required of stringent specifications for the whole spatial frequency errors. This work reveals the role of pad block’s support surface (PBSS) topography in measuring BK7 surface figure. Firstly, the PBSS topography was measured with laser displacement sensor. Secondly, the BK7 surface deformation at different pad blocks were simulated with finite element method and validated by experiments. Finally, a method was proposed to quantitively evaluate the different PBSS topography.
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 782 (2)
Open AccessThe Role of Pad Block’s Support Surface Topography in the Measurement of Optical Glass BK7’s Surface Figure
Large flat transmission mirrors made from optical glass BK7 are widely used in the high-power laser facility, which are required of stringent specifications for the whole spatial frequency errors. This work reveals the role of pad block’s support surface (PBSS) topography in measuring BK7 surface figure. Firstly, the PBSS topography was measured with laser displacement sensor. Secondly, the BK7 surface deformation at different pad blocks were simulated with finite element method and validated by experiments. Finally, a method was proposed to quantitively evaluate the different PBSS topography.
- 5 January 2020
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 9 (4) , 044011
Measurement of Contact Pressure Distribution Map at Workpiece/tin Lap Interface and Process Parameters Optimization During Full-Aperture Polishing With Tin Lap
Contact pressure at the workpiece/tin lap interface during full-aperture polishing is of great significance to workpiece’s material removal process. To promote the determinacy and efficiency of polishing process, a novel wireless contact pressure measurement system is developed. Further, the contact pressure distribution map is solved by the interpolation algorithm using the acquired contact pressure data at workpiece/ tin lap interface. Subsequently, a material removal amount model within given polishing time is proposed. Based on this model, process parameters are optimized with the genetic algorithms using contact pressure distribution map under specific workpiece’s initial surface figure and polishing conditions. Compared with random process parameters, the optimized process parameters can greatly improve the accuracy and convergence efficiency of workpiece’s surface figure in full-aperture polishing with tin lap, which is validated by the polishing experiments.
- 5 January 2020
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 9 (4) , 044011
Measurement of Contact Pressure Distribution Map at Workpiece/tin Lap Interface and Process Parameters Optimization During Full-Aperture Polishing With Tin Lap
Contact pressure at the workpiece/tin lap interface during full-aperture polishing is of great significance to workpiece’s material removal process. To promote the determinacy and efficiency of polishing process, a novel wireless contact pressure measurement system is developed. Further, the contact pressure distribution map is solved by the interpolation algorithm using the acquired contact pressure data at workpiece/ tin lap interface. Subsequently, a material removal amount model within given polishing time is proposed. Based on this model, process parameters are optimized with the genetic algorithms using contact pressure distribution map under specific workpiece’s initial surface figure and polishing conditions. Compared with random process parameters, the optimized process parameters can greatly improve the accuracy and convergence efficiency of workpiece’s surface figure in full-aperture polishing with tin lap, which is validated by the polishing experiments.
- 7 April 2019
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 10 (3) , 287-301
Correlation between polishing pad’s properties and material removal during full‐aperture polishing
Polishing pad plays a vital role in the fabrication of large flat optical elements during full‐aperture polishing. Material removal rate (MRR) and material removal distribution (MRD) describe the material removal process from the point of the global average removal rate and the spatial distribution of removed material, respectively. The pad's mechanical property characterized by compression modulus and morphological characteristic indicated by material ratio curve are used to qualitatively clarify the degression of MRR at different rough polishing stage. Moreover, the novel MRD model is proposed to quantitatively correlate the pad's mechanical and morphological characteristic with MRD. The radial surface profile predicted by MRD model meets well with the experimental results. Furthermore, the influence of pad viscoelastic property is used to explain the generation of additional MRD in experiment at the edge of workpiece.
- 7 April 2019
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 10 (3) , 287-301
Correlation between polishing pad’s properties and material removal during full‐aperture polishing
Polishing pad plays a vital role in the fabrication of large flat optical elements during full‐aperture polishing. Material removal rate (MRR) and material removal distribution (MRD) describe the material removal process from the point of the global average removal rate and the spatial distribution of removed material, respectively. The pad's mechanical property characterized by compression modulus and morphological characteristic indicated by material ratio curve are used to qualitatively clarify the degression of MRR at different rough polishing stage. Moreover, the novel MRD model is proposed to quantitatively correlate the pad's mechanical and morphological characteristic with MRD. The radial surface profile predicted by MRD model meets well with the experimental results. Furthermore, the influence of pad viscoelastic property is used to explain the generation of additional MRD in experiment at the edge of workpiece.
- 30 October 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 101 (1-4) , 137-146
Theoretical model and experimental analysis of non-uniform material removal during full-aperture polishing
- 30 October 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 101 (1-4) , 137-146
Theoretical model and experimental analysis of non-uniform material removal during full-aperture polishing
- 28 October 2018
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 102 (6) , 3129-3140
Surface shape development of the pitch lap under the loading of the conditioner in continuous polishing process
Continuous polishing using the pitch lap is a key process in finishing large flat optical elements. The optical elements’ surface figure is primarily dependent on the surface shape of the pitch lap, which is controlled by a large‐size conditioner. However, underlying fundamentals of the process control is not yet clear, and it remains empirical and nondeterministic to date. In this study, a novel analysis model is proposed for exploring the surface shape development of the pitch lap under the conditioner loading. The analysis model divides the polishing time into a series of segments, in which the shape variation of the pitch lap due to viscoelastic creep is derived from the pressure distribution at the conditioner‐lap contact interface. Further, a contact model of the lap and conditioner is built to obtain the pressure distribution at the interface, and a novel creep model is proposed for the viscoelastic behavior of the pitch lap under the pressure. The analysis model combined with the contact and viscoelastic models can be used to explore the pitch lap shape development under various conditions and hence reveal the underlying fundamentals of controlling the lap shape by the conditioner.
- 28 October 2018
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 102 (6) , 3129-3140
Surface shape development of the pitch lap under the loading of the conditioner in continuous polishing process
Continuous polishing using the pitch lap is a key process in finishing large flat optical elements. The optical elements’ surface figure is primarily dependent on the surface shape of the pitch lap, which is controlled by a large‐size conditioner. However, underlying fundamentals of the process control is not yet clear, and it remains empirical and nondeterministic to date. In this study, a novel analysis model is proposed for exploring the surface shape development of the pitch lap under the conditioner loading. The analysis model divides the polishing time into a series of segments, in which the shape variation of the pitch lap due to viscoelastic creep is derived from the pressure distribution at the conditioner‐lap contact interface. Further, a contact model of the lap and conditioner is built to obtain the pressure distribution at the interface, and a novel creep model is proposed for the viscoelastic behavior of the pitch lap under the pressure. The analysis model combined with the contact and viscoelastic models can be used to explore the pitch lap shape development under various conditions and hence reveal the underlying fundamentals of controlling the lap shape by the conditioner.