Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleg Panchenko has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Review on Friction Stir Welding of High-Strength Al-Zn-Mg Alloy: Insights on Second-Phase Particles

    by Keqi Wang, Anton Naumov, Evgenii Panchenko, Oleg Panchenko

    The friction stir welding (FSW) process is a unique combination of deformation and high temperature, which provides opportunities to modify microstructures through the adjustment of the processing parameters and is an ideal way to join non-weldable aluminum alloys by avoiding the formation of a molten pool. The 7xxx series heat-treatable aluminum alloys are widely used in the aerospace field as high-performance structural materials. The microstructure evolution and mechanical performance of these alloys are affected by the effects of thermomechanical processing, which provides opportunities to optimize the material properties by controlling microstructural features such as intermetallic constituent particles, dispersoids and nanoscale precipitates. This paper focuses on the basic principles of the thermal and mechanical effects generated during FSW on the evolution of second-phase particles in different zones of the weld.


  • Open Access

    Functional and Mechanical Properties of As-Deposited and Heat Treated WAAM-Built NiTi Shape-Memory Alloy

    by Arthur Khismatullin, Oleg Panchenko, Dmitry Kurushkin, Ivan Kladov, Anatoly Popovich

    In this work, MIG process was utilized for the wire arc additive manufacturing of the wall-shaped parts, using NiTi shape-memory alloy. High-scale specimens consisting of 20 layers were deposited by using Ni-rich (Ni55.56Ti wt.%) wire as a feedstock on the NiTi substrate with the identical chemical composition. One of two specimens was heat-treated at a temperature of 430 °C for 1 h. The influence of such a heat treatment on the microstructure, phase transformation temperatures, chemical and phase compositions, microhardness, and tensile and bending tests’ results is discussed. As-deposited metal successfully demonstrates superelastic behavior, except in the lower zone. In regard to the shape-memory effect, it was concluded that both the as-deposited and the heat-treated samples deformed in liquid nitrogen completely restored (100%) their shapes at an initial strain of 4–5%. An occurrence of the R-phase was found in both the as-deposited and the heat-treated specimens. The phase transformation temperatures, microstructure, and tensile and bending tests results were found to be anisotropic along the height of the specimens. The presented heat treatment led to changes in the functional and mechanical properties of the specimen, provided with the formation of finely dispersed Ni4Ti3, NiTi2, and Ni3Ti phases.


  • Open Access

    Composition of Organosilicate Coatings High-Temperature Breakdown Products and Their Distribution in the Weld

    by Leonid Zhabrev, Dmitry Kurushkin, Igor Mushnikov, Aleksey Shamshurin, Svetlana Chuppina, Oleg Panchenko

    The construction assembly and the repair of steel constructions painted with protective coatings are often carried out using arc welding. During the welding process, the coating in the weld zone is degrading. The protective coatings breakdown products are involved in the pore and non-metallic inclusion formation in the weld, the composition and distribution study of which makes it possible to analyze the reactions occurring during the welding. In this study, welding beads were deposited on the coated sheet surface by MAG welding. The distribution of inclusions (the average diameter and the relative content) along with the porosity in different bead zones were investigated by optical and scanning electron microscopy and digital image processing, and the chemical composition of inclusions was determined using energy-dispersive X-ray spectroscopy. The amount of diffusible hydrogen in the deposited metal was estimated with the vacuum method. In this work, four organosilicate coatings grades, differing in their purpose and heat resistance, were used, and their effect on the weld was studied.


  • Open Access

    Effect of Different Tool Probe Profiles on Material Flow of Al–Mg–Cu Alloy Joined by Friction Stir Welding

    by Anton Naumov, Evgenii Rylkov, Pavel Polyakov, Fedor Isupov, Andrey Rudskoy, Jong-Ning Aoh, Anatoly Popovich, Oleg Panchenko

    Friction Stir Welding (FSW) was utilized to butt−join 2024–T4 aluminum alloy plates of 1.9 mm thickness, using tools with conical and tapered hexagonal probe profiles. The characteristic effects of FSW using tools with tapered hexagonal probe profiles include an increase in the heat input and a significant modification of material flow, which have a positive effect on the metallurgical characteristics and mechanical performance of the weld. The differences in mechanical properties were interpreted through macrostructural changes and mechanical properties of the welded joints, which were supported by numerical simulation results on temperature distribution and material flow. The material flow resulting from the tapered hexagonal probe was more complicated than that of the conical probe. If in the first case, the dynamic viscosity and strain rate are homogeneously distributed around the probe, but in the case of the tapered hexagonal probe tool, the zones with maximum values of strain rates and minimum values of dynamic viscosity are located along the six tapered edges of the probe.


  • Open Access

    Gas Metal Arc Welding Modes in Wire Arc Additive Manufacturing of Ti-6Al-4V

    by Oleg Panchenko, Dmitry Kurushkin, Fedor Isupov, Anton Naumov, Ivan Kladov, Margarita Surenkova

    In wire arc additive manufacturing of Ti-alloy parts (Ti-WAAM) gas metal arc welding (GMAW) can be applied for complex parts printing. However, due to the specific properties of Ti, GMAW of Ti-alloys is complicated. In this work, three different types of metal transfer modes during Ti-WAAM were investigated: Cold Metal Transfer, controlled short circuiting metal transfer, and self-regulated metal transfer at a direct current with a negative electrode. Metal transfer modes were studied using captured waveform and high-speed video analysis. Using these modes, three walls were manufactured; the geometry preservation stability was estimated and compared using effective wall width calculation, the microstructure was analyzed using optical microscopy. Transfer process data showed that arc wandering depends not only on cathode spot instabilities, but also on anode processing properties. Microstructure analysis showed that each produced wall consists of phases and structures inherent for Ti-WAAM. α-basketweave in the center of and α-colony on the grain boundary of epitaxially grown β-grains were found with heat affected zone bands along the height of the walls, so that the microstructure did not depend on metal transfer dramatically. However, the geometry preservation stability was higher in the wall, produced with controlled short circuiting metal transfer.


  • Open Access

    The Coatings Breakdown Products Influence on the Gas Metal Arc Welding Parameters

    by Leonid Zhabrev, Dmitry Kurushkin, Igor Mushnikov, Oleg Panchenko

    The installation and renovation works of steel structures are often performed using gas metal arc welding. Thereby, the welded elements of these structures are frequently protected by a variety of primers and coatings, especially in shipbuilding. Complex nonequilibrium physical and chemical processes occurring under the influence of high temperatures and electric arc discharge, as well as the presence of the products that affect the welding parameters, have a significant impact on the joints’ quality. Experimental studies on the coatings’ breakdown products influence on the gas metal arc welding parameters were performed with epoxy, alkyd, polyacrylate, polyvinyl butyral primers, epoxy zinc filled, vinyl chloride, vinyl isobutyl, and organosilicate coatings. The peculiarity of welding current waveform parameters was studied using oscillograms processing. It was found that the main coatings breakdown products that influence the current waveform are oxygen and carbon monoxide.


  • Open Access

    EVALUATION OF COATINGS TENDENCY TO THE PORES AND NON-METAL INCLUSIONS FORMATION IN A WELD

    by L. Zhabrev, S. Chuppina, A. Shamshurin, E. Lebedeva, O. Panchenko

    The task of welding steel elements painted with various coatings is found in a number of industries at the stages of factory assembly and installation of large-sized structures, as well as during repair and restoration work. The porosity of the welded metal is the most common defect in electric arc welding without removing the coating, and the tendency to pore formation is a normalized parameter in the certification of interoperable primers (EN ISO 17652-2: 2003). The studies carried out cover wide-spread polyacrylate, alkyd, epoxy, polyvinyl butyral primers in an extended working thicknesses range. In addition, the evaluation technique is used for zinc-filled and organosilicate protective coat-ings. Based on the study of the nonmetallic inclusions composition in a weld by energy dispersive X-ray spectroscopy and using a scanning electron microscope, the behavior features of the coatings de-struction products and their derivatives during physical and chemical transformations under welding are described. The technological features of welding without coating removing are noted: stability of the mode parameters, resistance to metal spraying and coating burnout activity in the areas adjacent to a weld.