Fedor Isupov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fedor Isupov has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Anton Naumov
Lightweight Materials and Structures Laboratory, Peter the Great St. Petersburg Polytechnic University, 195251 St. Petersburg, Russia
5 shared publications - Oleg Panchenko
Laboratory of Lightweight Materials and Structures, Institute of Machinery, Materials, and Transport, Peter the Great St. Petersburg Polytechnic University, 29 Polytechnicheskaya St., 195251 St. Petersburg, Russia
3 shared publications - Andrey Ivanovich Rudskoy
Peter the Great St. Petersburg Polytechnic University
2 shared publications A. A. Popovich
New Industrial Technologies Center, Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russia
1 shared publication- Ahmad Alali Alkhalaf
Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russian Federation
1 shared publication - Aleksei Obrosov
Department of Metallurgy and Materials Technology, Brandenburg University of Technology Cottbus-Senftenberg, 03046 Cottbus, Germany
1 shared publication
Latest Publications
- 10 July 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 128 (1-2) , 373-389
The effect of impulses on precipitation behavior in 7075-T6 aluminum alloy joint by impulse friction stir welding
- 10 July 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 128 (1-2) , 373-389
The effect of impulses on precipitation behavior in 7075-T6 aluminum alloy joint by impulse friction stir welding
- Open Access
Effect of Different Tool Probe Profiles on Material Flow of Al–Mg–Cu Alloy Joined by Friction Stir Welding
Friction Stir Welding (FSW) was utilized to butt−join 2024–T4 aluminum alloy plates of 1.9 mm thickness, using tools with conical and tapered hexagonal probe profiles. The characteristic effects of FSW using tools with tapered hexagonal probe profiles include an increase in the heat input and a significant modification of material flow, which have a positive effect on the metallurgical characteristics and mechanical performance of the weld. The differences in mechanical properties were interpreted through macrostructural changes and mechanical properties of the welded joints, which were supported by numerical simulation results on temperature distribution and material flow. The material flow resulting from the tapered hexagonal probe was more complicated than that of the conical probe. If in the first case, the dynamic viscosity and strain rate are homogeneously distributed around the probe, but in the case of the tapered hexagonal probe tool, the zones with maximum values of strain rates and minimum values of dynamic viscosity are located along the six tapered edges of the probe.
Open AccessEffect of Different Tool Probe Profiles on Material Flow of Al–Mg–Cu Alloy Joined by Friction Stir Welding
Friction Stir Welding (FSW) was utilized to butt−join 2024–T4 aluminum alloy plates of 1.9 mm thickness, using tools with conical and tapered hexagonal probe profiles. The characteristic effects of FSW using tools with tapered hexagonal probe profiles include an increase in the heat input and a significant modification of material flow, which have a positive effect on the metallurgical characteristics and mechanical performance of the weld. The differences in mechanical properties were interpreted through macrostructural changes and mechanical properties of the welded joints, which were supported by numerical simulation results on temperature distribution and material flow. The material flow resulting from the tapered hexagonal probe was more complicated than that of the conical probe. If in the first case, the dynamic viscosity and strain rate are homogeneously distributed around the probe, but in the case of the tapered hexagonal probe tool, the zones with maximum values of strain rates and minimum values of dynamic viscosity are located along the six tapered edges of the probe.
- Open Access
Gas Metal Arc Welding Modes in Wire Arc Additive Manufacturing of Ti-6Al-4V
In wire arc additive manufacturing of Ti-alloy parts (Ti-WAAM) gas metal arc welding (GMAW) can be applied for complex parts printing. However, due to the specific properties of Ti, GMAW of Ti-alloys is complicated. In this work, three different types of metal transfer modes during Ti-WAAM were investigated: Cold Metal Transfer, controlled short circuiting metal transfer, and self-regulated metal transfer at a direct current with a negative electrode. Metal transfer modes were studied using captured waveform and high-speed video analysis. Using these modes, three walls were manufactured; the geometry preservation stability was estimated and compared using effective wall width calculation, the microstructure was analyzed using optical microscopy. Transfer process data showed that arc wandering depends not only on cathode spot instabilities, but also on anode processing properties. Microstructure analysis showed that each produced wall consists of phases and structures inherent for Ti-WAAM. α-basketweave in the center of and α-colony on the grain boundary of epitaxially grown β-grains were found with heat affected zone bands along the height of the walls, so that the microstructure did not depend on metal transfer dramatically. However, the geometry preservation stability was higher in the wall, produced with controlled short circuiting metal transfer.
Open AccessGas Metal Arc Welding Modes in Wire Arc Additive Manufacturing of Ti-6Al-4V
In wire arc additive manufacturing of Ti-alloy parts (Ti-WAAM) gas metal arc welding (GMAW) can be applied for complex parts printing. However, due to the specific properties of Ti, GMAW of Ti-alloys is complicated. In this work, three different types of metal transfer modes during Ti-WAAM were investigated: Cold Metal Transfer, controlled short circuiting metal transfer, and self-regulated metal transfer at a direct current with a negative electrode. Metal transfer modes were studied using captured waveform and high-speed video analysis. Using these modes, three walls were manufactured; the geometry preservation stability was estimated and compared using effective wall width calculation, the microstructure was analyzed using optical microscopy. Transfer process data showed that arc wandering depends not only on cathode spot instabilities, but also on anode processing properties. Microstructure analysis showed that each produced wall consists of phases and structures inherent for Ti-WAAM. α-basketweave in the center of and α-colony on the grain boundary of epitaxially grown β-grains were found with heat affected zone bands along the height of the walls, so that the microstructure did not depend on metal transfer dramatically. However, the geometry preservation stability was higher in the wall, produced with controlled short circuiting metal transfer.
- 17 February 2021
- Published by Springer Nature
- p. 209-217
Temperature Distribution During Friction Stir Spot Welding of Thin AA 6082-T6 and AA 5082-O Sheets
- 17 February 2021
- Published by Springer Nature
- p. 209-217
Temperature Distribution During Friction Stir Spot Welding of Thin AA 6082-T6 and AA 5082-O Sheets
- Open Access
Metallurgical and Mechanical Characterization of High-Speed Friction Stir Welded AA 6082-T6 Aluminum Alloy
The objective of this study was to investigate the effect of the high welding speed on the mechanical properties and their relations to microstructural characteristics of butt friction stir welded joints with the use of 6082-T6 aluminum alloy. The aluminum sheets of 2.0 mm thick were friction stir welded at low (conventional FSW) and high welding speeds (HSFSW) of 200 and 2500 mm/min, respectively. The grain size in the nugget zone (NZ) was decreased; the width of the softened region was narrowed down as well as the lowest microhardness value located in the heat-affected zone (HAZ) was enhanced by HSFSW. The increasing welding speed resulted in the higher ultimate tensile strength and lower elongation, but it had a slight influence on the yield strength. The differences in mechanical properties were explained by analysis of microstructural changes and tensile fracture surfaces of the welded joints, supported by the results of the numerical simulation of the temperature distribution and material flow. The fracture of the conventional FSW joint occurred in the HAZ, the weakest weld region, while all HSFSW joints raptured in the NZ. This demonstrated that both structural characteristics and microhardness distribution influenced the actual fracture locations.
Open AccessMetallurgical and Mechanical Characterization of High-Speed Friction Stir Welded AA 6082-T6 Aluminum Alloy
The objective of this study was to investigate the effect of the high welding speed on the mechanical properties and their relations to microstructural characteristics of butt friction stir welded joints with the use of 6082-T6 aluminum alloy. The aluminum sheets of 2.0 mm thick were friction stir welded at low (conventional FSW) and high welding speeds (HSFSW) of 200 and 2500 mm/min, respectively. The grain size in the nugget zone (NZ) was decreased; the width of the softened region was narrowed down as well as the lowest microhardness value located in the heat-affected zone (HAZ) was enhanced by HSFSW. The increasing welding speed resulted in the higher ultimate tensile strength and lower elongation, but it had a slight influence on the yield strength. The differences in mechanical properties were explained by analysis of microstructural changes and tensile fracture surfaces of the welded joints, supported by the results of the numerical simulation of the temperature distribution and material flow. The fracture of the conventional FSW joint occurred in the HAZ, the weakest weld region, while all HSFSW joints raptured in the NZ. This demonstrated that both structural characteristics and microhardness distribution influenced the actual fracture locations.
- 1 December 2019
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2019 (13) , 1399-1406
Consumable Tool for Coating Deposition by Joint Deformation of the Base and Tool Materials
A coating made of an Al–5Mg aluminum alloy is deposited onto a substrate of the same alloy due to the joint deformation of the base and tool materials via friction. A mathematical simulation is used to choose the geometry of the tool that ensures its operability and stability during coating deposition. One-layer and multilayer coatings and butt joints of 2-mm-thick sheets are formed. The joints have a fine-grained structure with the grain size that is smaller than the grain size in the substrate by a factor of 5–10. The microhardness distribution across the deposited layers is nonuniform: the hardness increases from the substrate to the upper layer.
- 1 December 2019
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2019 (13) , 1399-1406
Consumable Tool for Coating Deposition by Joint Deformation of the Base and Tool Materials
A coating made of an Al–5Mg aluminum alloy is deposited onto a substrate of the same alloy due to the joint deformation of the base and tool materials via friction. A mathematical simulation is used to choose the geometry of the tool that ensures its operability and stability during coating deposition. One-layer and multilayer coatings and butt joints of 2-mm-thick sheets are formed. The joints have a fine-grained structure with the grain size that is smaller than the grain size in the substrate by a factor of 5–10. The microhardness distribution across the deposited layers is nonuniform: the hardness increases from the substrate to the upper layer.