MMMasatoshi Mitsuhara

Masatoshi Mitsuhara

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Masatoshi Mitsuhara has a total of 46 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effects of Manganese on Microstructure and Work-hardening Behavior of Low-carbon Lath Martensitic Steel

    by Kotaro Ueno, Rina Fujimura, Masatoshi Mitsuhara, Koutarou Hayashi, Shunji Hiwatashi, Manabu Takahashi

    Microstructures of lath martensite have been studied intensively to understand their effect on the mechanical properties of steels. It is, however, said that the relation between microstructural factors and mechanical properties has not been clarified yet. The plastic deformation behavior of fully lath martensitic steels has become important because they are applied to automobile body structures such as bumper reinforcement. It is, therefore, important to understand the microstructural factors that control the work-hardening behavior of fully martensitic steels. Although we could not clarify differences in microstructural factors when manganese (Mn) concentrations of steels are altered, the work-hardening of 8 mass%Mn martensitic steel is much higher than that of 5 mass%Mn martensitic steel. It was found using the digital image correlation (DIC) method, that the strain concentration due to the in-lath-plane slip deformation is more developed in 5 mass%Mn martensitic steel than 8 mass%Mn martensitic steel. Transmission electron microscope (TEM) observations revealed the existence of two types of fine twins inside laths. Long twins that are parallel to the longitude of the lath are observed both in 5 mass%Mn and 8 mass%Mn martensitic steels. Short twins that partially cross the laths, on the other hand, can only be found in 8 mass%Mn martensitic steel. Since twin boundaries are high angle boundaries, the short twins are supposed to prevent the development of in-lath-plane slip deformation. This seems to be the mechanism of higher work-hardening behavior observed in 8 mass%Mn martensitic steel.


  • Effect of impurity elements on the creep rupture strength of Gr. 91 steel welded joints at 650 °C

    by Katsuhiro Sato, Masatoshi Mitsuhara, Kodai Nagata, Keiji Kubushiro, Kyohei Nomura, Takahiro Kimura, Yoshiki Shioda, Kota Sawada, Kazuhiro Kimura, Hideharu Nakashima


  • Oil Film Formation and Delamination Process on Nanostructured Surfaces in Boundary Lubrication: A Coarse-Grained Molecular Dynamics Study

    by Shizhe Deng, Atsushi Kubo, Yoshikazu Todaka, Yoshinori Shiihara, Masatoshi Mitsuhara, Yoshitaka Umeno

    A series of coarse-grained molecular dynamics simulations were conducted to investigate the temporal evolution of frictional behaviors of lubricants between sliding nanostructured iron surfaces. Grain boundary atoms were given a stronger interaction with the lubricant molecules. We varied the surface distance and interaction strength between grain boundary atoms and lubricants. It was found that, below the critical compressive stress, the oil film detached from the surface at first and then attached to it after several nanoseconds due to the localized molecular rearrangement within lubricants and the enhancement of interaction between lubricants and iron surfaces. The transition times required for oil film formation and de-lamination both increased as it approached the critical compressive stress. Larger interaction strength increased the delamination time but barely affected the formation time.


  • Open Access

    Tensile Deformation Behaviors of Pure Ti with Different Grain Sizes under Wide-Range of Strain Rate

    by Misaki Deguchi, Shigeto Yamasaki, Masatoshi Mitsuhara, Hideharu Nakashima, Genki Tsukamoto, Tomonori Kunieda

    In this study, pure titanium equivalent to Grade 1 was subjected to tensile tests at strain rates ranging from 10−6 to 100 s−1 to investigate the relationship between its mechanical properties and its twinning and slip. Deformation properties and microstructures of samples having average grain sizes of 210 μm (Ti-210), 30 μm (Ti-30), and 5 μm (Ti-5) were evaluated. With increasing strain rates, the 0.2% proof stress and ultimate tensile strength increased for all samples; the fracture strain increased for Ti-210, decreased for Ti-5, and changed negligibly for Ti-30. Comparing high (100 s−1) and low (10−6 s−1) strain rates, twinning occurred more frequently in Ti-30 and Ti-210 at high strain rates, but the frequency did not change in Ti-5. The frequency of 1st order pyramidal slip tended to be higher in Ti-30 and Ti-5 at low strain rates. The higher ductility exhibited by Ti-210 at high strain rates was attributed to the high frequency of twinning. In contrast, the higher ductility of Ti-5 at low strain rates was attributed to the activity of the 1st order pyramidal slip.


  • Open Access

    High Temperature Mechanical Properties and Microstructure in 9Cr or 12Cr Oxide Dispersion Strengthened Steels

    by Masatoshi Mitsuhara, Koichi Kurino, Yasuhide Yano, Satoshi Ohtsuka, Takeshi Toyama, Masato Ohnuma, Hideharu Nakashima

    Oxide Dispersion Strengthened (ODS) ferritic steel, a candidate material for fast reactor fuel cladding, has low thermal expansion, good thermal conductivity, and excellent resistance to irradiation damage and high temperature strength. The origin of the excellent high-temperature strength lies in the dispersion of fine oxides. In this study, creep tests at 700°C or 750°C, which are close to the operating temperatures of fast reactors, and high-temperature tensile tests at 900°C to 1350°C, which simulate accident conditions, were conducted on 9Cr ODS ferritic steels, M11 and MP23, and 12Cr ODS ferritic steel, F14, to confirm the growth behavior of oxides. In the M11 and F14 creep test samples, there was little oxide growth or decrease in number density from the initial state, indicating that dispersion strengthening by oxides was effective during deformation. After creep deformation of F14, the development of dislocation substructures such as dislocation walls and subgrain boundaries was hardly observed, and mobile dislocations were homogeneously distributed in the grains. The dislocation density increased with increasing stress during the creep test. In the high-temperature ring tensile tests of MP23 and F14, the strength of both steels decreased at higher temperatures. In MP23, elongation decreased with increasing test temperature from 900°C to 1100°C, but increased at 1200°C, decreased drastically at 1250°C, and increased again at 1300°C. In F14, elongation decreased with increasing temperature. It was inferred that the formation of the δ-ferrite phase was responsible for this complex change in mechanical properties of MP23 from 1200 to 1300°C.


  • Open Access

    Experimental Aspects of Kink and Pre-kink Formation Process in Mg-Zn-Y Alloy with LPSO Phase

    by Masatoshi Mitsuhara

    The kink band formation process in Mg-6%Zn-9%Y alloy with the long-period stacking ordered (LPSO) phase was investigated in detail by in-situ compressive test and observation by SEM, and it succeeded in capturing the microstructural change with no surface relief which should be called as the pre-kink band. Using the SEM and the TEM analysis, it clearly founded that the pre-kink

  • Open Access

    Electron tomography imaging methods with diffraction contrast for materials research

    by Satoshi Hata, Hiromitsu Furukawa, Takashi Gondo, Daisuke Hirakami, Noritaka Horii, Ken-Ichi Ikeda, Katsumi Kawamoto, Kosuke Kimura, Syo Matsumura, Masatoshi Mitsuhara, et al.

    Transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) enable the visualization of three-dimensional (3D) microstructures ranging from atomic to micrometer scales using 3D reconstruction techniques based on computed tomography algorithms. This 3D microscopy method is called electron tomography (ET) and has been utilized in the fields of materials science and engineering for more than two decades. Although atomic resolution is one of the current topics in ET research, the development and deployment of intermediate-resolution (non-atomic-resolution) ET imaging methods have garnered considerable attention from researchers. This research trend is probably not irrelevant due to the fact that the spatial resolution and functionality of 3D imaging methods of scanning electron microscopy (SEM) and X-ray microscopy have come to overlap with those of ET. In other words, there may be multiple ways to carry out 3D visualization using different microscopy methods for nanometer-scale objects in materials. From the above standpoint, this review paper aims to (i) describe the current status and issues of intermediate-resolution ET with regard to enhancing the effectiveness of TEM/STEM imaging and (ii) discuss promising applications of state-of-the-art intermediate-resolution ET for materials research with a particular focus on diffraction contrast ET for crystalline microstructures (superlattice domains and dislocations) including a demonstration of in situ dislocation tomography.


  • Open Access

    Effect of Fe Addition on Heat-Resistant Aluminum Alloys Produced by Selective Laser Melting

    by Shigeto Yamasaki, Tomo Okuhira, Masatoshi Mitsuhara, Hideharu Nakashima, Jun Kusui, Mitsuru Adachi

    The effect of Fe addition on the high-temperature mechanical properties of heat-resistant aluminum alloys produced by selective laser melting (SLM) was investigated in relation to the alloy microstructures. Fe is generally detrimental to the properties of cast aluminum alloys; however, we found that Fe-containing alloys produced by SLM had improved high-temperature strength and good ductility. Microstructural observations revealed that the increase in the high-temperature strength of the alloys was due to the dispersion of fine rod-shaped Fe-Si-Ni particles unique to the SLM material instead of the cell-like structure of eutectic Si.