Alain Reiser
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Alain Reiser has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Ralph Spolenak
Laboratory for Nanometallurgy, Department of Materials, ETH Zurich, Zurich, Switzerland
10 shared publications Ralph Spolenak
ETH Zurich
5 shared publications- Alla S. Sologubenko
Laboratory for Nanometallurgy, Department of Materials, ETH Zurich, Zurich, Switzerland
3 shared publications - Christopher A. Schuh
Department of Materials Science and Engineering, Northwestern University, Evanston, USA
3 shared publications - Dimos Poulikakos
Laboratory of Thermodynamics in Emerging Technologies, Department of Mechanical and Process Engineering, ETH Zurich, Zurich, Switzerland
3 shared publications - Jeffrey Martin Wheeler
Laboratory for Nanometallurgy, Department of Materials, ETH Zurich, Zurich, Switzerland
3 shared publications
Latest Publications
- Open Access
Microscale Metal Additive Manufacturing by Solid‐State Impact Bonding of Shaped Thin Films
The deposition of device‐grade inorganic materials is one key challenge toward the implementation of additive manufacturing (AM) in microfabrication, and to that end, a broad range of physico‐chemical principles has been explored for 3D fabrication with micro‐ and nanoscale resolution. Yet, for metals, a process that achieves material quality rivalling that of established thin‐film deposition methods, and at the same time, has the potential to combine high throughput production with a broad palette of processable materials, is still lacking. Here, the kinetic, solid‐state bonding of metal thin films for the additive assembly of high‐purity, high‐density metals with micrometer‐scale precision is introduced. Indirect laser ablation accelerates micrometer‐thick gold films to hundreds of meters per second without their heating or ablation. Their subsequent impact on the substrate above a critical velocity forms a permanent, metallic bond in the solid state. Stacked layers are of high density (>99%). By defining thin‐film layers with established lithographic methods prior to launch, a variable feature size (2–50 µm), arbitrary shape of bonded layers, and parallel transfer of up to 36 independent film units in a single shot, is demonstrated. Thus, the solid‐state kinetic bonding principle as a viable and potentially versatile route for micro‐scale AM of metals is established.
Open AccessMicroscale Metal Additive Manufacturing by Solid‐State Impact Bonding of Shaped Thin Films
The deposition of device‐grade inorganic materials is one key challenge toward the implementation of additive manufacturing (AM) in microfabrication, and to that end, a broad range of physico‐chemical principles has been explored for 3D fabrication with micro‐ and nanoscale resolution. Yet, for metals, a process that achieves material quality rivalling that of established thin‐film deposition methods, and at the same time, has the potential to combine high throughput production with a broad palette of processable materials, is still lacking. Here, the kinetic, solid‐state bonding of metal thin films for the additive assembly of high‐purity, high‐density metals with micrometer‐scale precision is introduced. Indirect laser ablation accelerates micrometer‐thick gold films to hundreds of meters per second without their heating or ablation. Their subsequent impact on the substrate above a critical velocity forms a permanent, metallic bond in the solid state. Stacked layers are of high density (>99%). By defining thin‐film layers with established lithographic methods prior to launch, a variable feature size (2–50 µm), arbitrary shape of bonded layers, and parallel transfer of up to 36 independent film units in a single shot, is demonstrated. Thus, the solid‐state kinetic bonding principle as a viable and potentially versatile route for micro‐scale AM of metals is established.
- 30 October 2024
- Published by Springer Nature in Nature Materials
- Vol. 23 (12) , 1604-1605
Direct laser 3D nanowriting of metals and their alloys
- 30 October 2024
- Published by Springer Nature in Nature Materials
- Vol. 23 (12) , 1604-1605
Direct laser 3D nanowriting of metals and their alloys
- Open Access
- 15 October 2024
- Published by Springer Nature in Research Square
Microscale metal additive manufacturing by solid-state impact bonding of shaped thin films
The deposition of device-grade inorganic materials is one key challenge towards the implementation of additive manufacturing in microfabrication, and to that end, a broad range of physico-chemical principles has been explored for 3D fabrication with micro- and nanoscale resolution. Yet, for metals, we still lack a process that achieves material quality rivaling that of established thin-film deposition methods and at the same time has potential to combine high throughput production with a broad palette of processable materials. Here we introduce the kinetic, solid-state bonding of metal thin films for the additive assembly of high-purity, high-density metals with micrometer-scale precision. Indirect laser ablation accelerates micrometer-thick gold films to hundreds of meters per second without their heating or ablation. Their subsequent impact on the substrate above a critical velocity forms a permanent, metallic bond in the solid state. Stacked layers are of high density (>99%). By defining thin-film layers with established lithographical methods prior to launch, we demonstrate a variable feature size (2-50 μm), arbitrary shape of bonded layers and parallel transfer of up to 36 independent film units in a single shot. We thus establish the solid-state kinetic bonding principle as a viable and potentially versatile route for micro-scale AM of metals.
- 15 October 2024
- Published by Springer Nature in Research Square
Open AccessMicroscale metal additive manufacturing by solid-state impact bonding of shaped thin films
The deposition of device-grade inorganic materials is one key challenge towards the implementation of additive manufacturing in microfabrication, and to that end, a broad range of physico-chemical principles has been explored for 3D fabrication with micro- and nanoscale resolution. Yet, for metals, we still lack a process that achieves material quality rivaling that of established thin-film deposition methods and at the same time has potential to combine high throughput production with a broad palette of processable materials. Here we introduce the kinetic, solid-state bonding of metal thin films for the additive assembly of high-purity, high-density metals with micrometer-scale precision. Indirect laser ablation accelerates micrometer-thick gold films to hundreds of meters per second without their heating or ablation. Their subsequent impact on the substrate above a critical velocity forms a permanent, metallic bond in the solid state. Stacked layers are of high density (>99%). By defining thin-film layers with established lithographical methods prior to launch, we demonstrate a variable feature size (2-50 μm), arbitrary shape of bonded layers and parallel transfer of up to 36 independent film units in a single shot. We thus establish the solid-state kinetic bonding principle as a viable and potentially versatile route for micro-scale AM of metals.
- Open Access
- 16 August 2024
- Published by Elsevier in Acta Materialia
- Vol. 281
Towards an understanding of particle-scale flaws and microstructure evolution in cold spray via accumulation of single particle impacts
- 16 August 2024
- Published by Elsevier in Acta Materialia
- Vol. 281
Open AccessTowards an understanding of particle-scale flaws and microstructure evolution in cold spray via accumulation of single particle impacts
- Open Access
- 6 January 2024
- Published by Wiley in Small Methods
- Vol. 8 (7) , e2301247
Direct In‐ and Out‐of‐Plane Writing of Metals on Insulators by Electron‐Beam‐Enabled, Confined Electrodeposition with Submicrometer Feature Size
Additive microfabrication processes based on localized electroplating enable the one‐step deposition of micro‐scale metal structures with outstanding performance, e.g., high electrical conductivity and mechanical strength. They are therefore evaluated as an exciting and enabling addition to the existing repertoire of microfabrication technologies. Yet, electrochemical processes are generally restricted to conductive or semiconductive substrates, precluding their application in the manufacturing of functional electric devices where direct deposition onto insulators is often required. Here, the direct, localized electrodeposition of copper on a variety of insulating substrates, namely Al2O3, glass and flexible polyethylene, is demonstrated, enabled by electron‐beam‐induced reduction in a highly confined liquid electrolyte reservoir. The nanometer‐size of the electrolyte reservoir, fed by electrohydrodynamic ejection, enables a minimal feature size on the order of 200 nm. The fact that the transient reservoir is established and stabilized by electrohydrodynamic ejection rather than specialized liquid cells can offer greater flexibility toward deposition on arbitrary substrate geometries and materials. Installed in a low‐vacuum scanning electron microscope, the setup further allows for operando, nanoscale observation and analysis of the manufacturing process.
- 6 January 2024
- Published by Wiley in Small Methods
- Vol. 8 (7) , e2301247
Open AccessDirect In‐ and Out‐of‐Plane Writing of Metals on Insulators by Electron‐Beam‐Enabled, Confined Electrodeposition with Submicrometer Feature Size
Additive microfabrication processes based on localized electroplating enable the one‐step deposition of micro‐scale metal structures with outstanding performance, e.g., high electrical conductivity and mechanical strength. They are therefore evaluated as an exciting and enabling addition to the existing repertoire of microfabrication technologies. Yet, electrochemical processes are generally restricted to conductive or semiconductive substrates, precluding their application in the manufacturing of functional electric devices where direct deposition onto insulators is often required. Here, the direct, localized electrodeposition of copper on a variety of insulating substrates, namely Al2O3, glass and flexible polyethylene, is demonstrated, enabled by electron‐beam‐induced reduction in a highly confined liquid electrolyte reservoir. The nanometer‐size of the electrolyte reservoir, fed by electrohydrodynamic ejection, enables a minimal feature size on the order of 200 nm. The fact that the transient reservoir is established and stabilized by electrohydrodynamic ejection rather than specialized liquid cells can offer greater flexibility toward deposition on arbitrary substrate geometries and materials. Installed in a low‐vacuum scanning electron microscope, the setup further allows for operando, nanoscale observation and analysis of the manufacturing process.
- Open Access
- 29 September 2023
- Published by Elsevier in Materials & Design
- Vol. 234
Micron-scale additive manufacturing of binary and ternary alloys by electrohydrodynamic redox 3D printing
- 29 September 2023
- Published by Elsevier in Materials & Design
- Vol. 234
Open AccessMicron-scale additive manufacturing of binary and ternary alloys by electrohydrodynamic redox 3D printing
- Open Access
- 14 December 2022
- Published by Wiley in Small Methods
- Vol. 7 (1) , e2201028
Microparticle Impact Testing at High Precision, Higher Temperatures, and with Lithographically Patterned Projectiles
In the first decade of high‐velocity microparticle impact research, hardly any modification of the original experimental setup has been necessary. However, future avenues for the field require advancements of the experimental method to expand both the impact variables that can be quantitatively assessed and the materials and phenomena that can be studied. This work explores new design concepts for the launch pad (the assembly that launches microparticles upon laser ablation) that can address the root causes of many experimental challenges that may limit the technique in the future. Among the design changes contemplated, the substitution of a stiff glass launch layer for the standard elastomeric polymer layer offers a number of improvements. First, it facilitates a reduction of the gap between launch pad and target from hundreds to tens of micrometers and thus unlocks a reproducibility in targeting a specific impact location better than the diameter of the test particle itself (±1.75 µm for SiO2 particles 7.38 µm in diameter). Second, the inert glass surface enables experiments at higher temperatures than previously possible. Finally—as demonstrated by the launch of thin‐film Au disks—a launch pad made of materials standard in microfabrication paves the way to facile microfabrication of advanced impactors.
- 14 December 2022
- Published by Wiley in Small Methods
- Vol. 7 (1) , e2201028
Open AccessMicroparticle Impact Testing at High Precision, Higher Temperatures, and with Lithographically Patterned Projectiles
In the first decade of high‐velocity microparticle impact research, hardly any modification of the original experimental setup has been necessary. However, future avenues for the field require advancements of the experimental method to expand both the impact variables that can be quantitatively assessed and the materials and phenomena that can be studied. This work explores new design concepts for the launch pad (the assembly that launches microparticles upon laser ablation) that can address the root causes of many experimental challenges that may limit the technique in the future. Among the design changes contemplated, the substitution of a stiff glass launch layer for the standard elastomeric polymer layer offers a number of improvements. First, it facilitates a reduction of the gap between launch pad and target from hundreds to tens of micrometers and thus unlocks a reproducibility in targeting a specific impact location better than the diameter of the test particle itself (±1.75 µm for SiO2 particles 7.38 µm in diameter). Second, the inert glass surface enables experiments at higher temperatures than previously possible. Finally—as demonstrated by the launch of thin‐film Au disks—a launch pad made of materials standard in microfabrication paves the way to facile microfabrication of advanced impactors.
- Open Access
- 10 November 2022
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 14 (46) , 17418-17427
Additive manufacturing of Zn with submicron resolution and its conversion into Zn/ZnO core–shell structures
Electrohydrodynamic-redox printing allows deposition of single-crystal-like Zn structures with a resolution of 250 nm, which can be thermally oxidized to Zn/ZnO core–shell structures.
- 10 November 2022
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 14 (46) , 17418-17427
Open AccessAdditive manufacturing of Zn with submicron resolution and its conversion into Zn/ZnO core–shell structures
Electrohydrodynamic-redox printing allows deposition of single-crystal-like Zn structures with a resolution of 250 nm, which can be thermally oxidized to Zn/ZnO core–shell structures.
- Open Access
Targeted Additive Micromodulation of Grain Size in Nanocrystalline Copper Nanostructures by Electrohydrodynamic Redox 3D Printing
The control of materials’ microstructure is both a necessity and an opportunity for micro/nanometer‐scale additive manufacturing technologies. On the one hand, optimization of purity and defect density of printed metals is a prerequisite for their application in microfabrication. On the other hand, the additive approach to materials deposition with highest spatial resolution offers unique opportunities for the fabrication of materials with complex, 3D graded composition or microstructure. As a first step toward both—optimization of properties and site‐specific tuning of microstructure—an overview of the wide range of microstructure accessed in pure copper (up to >99.9 at.%) by electrohydrodynamic redox 3D printing is presented, and on‐the‐fly modulation of grain size in copper with smallest segments ≈400 nm in length is shown. Control of microstructure and materials properties by in situ adjustment of the printing voltage is demonstrated by variation of grain size by one order of magnitude and corresponding compression strength by a factor of two. Based on transmission electron microscopy and atom probe tomography, it is suggested that the small grain size is a direct consequence of intermittent solvent drying at the growth interface at low printing voltages, while larger grains are enabled by the permanent presence of solvent at higher potentials.
Open AccessTargeted Additive Micromodulation of Grain Size in Nanocrystalline Copper Nanostructures by Electrohydrodynamic Redox 3D Printing
The control of materials’ microstructure is both a necessity and an opportunity for micro/nanometer‐scale additive manufacturing technologies. On the one hand, optimization of purity and defect density of printed metals is a prerequisite for their application in microfabrication. On the other hand, the additive approach to materials deposition with highest spatial resolution offers unique opportunities for the fabrication of materials with complex, 3D graded composition or microstructure. As a first step toward both—optimization of properties and site‐specific tuning of microstructure—an overview of the wide range of microstructure accessed in pure copper (up to >99.9 at.%) by electrohydrodynamic redox 3D printing is presented, and on‐the‐fly modulation of grain size in copper with smallest segments ≈400 nm in length is shown. Control of microstructure and materials properties by in situ adjustment of the printing voltage is demonstrated by variation of grain size by one order of magnitude and corresponding compression strength by a factor of two. Based on transmission electron microscopy and atom probe tomography, it is suggested that the small grain size is a direct consequence of intermittent solvent drying at the growth interface at low printing voltages, while larger grains are enabled by the permanent presence of solvent at higher potentials.
- Open Access
- 28 March 2022
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 14 (14) , 5579-5588
Nanoscale electrochemical 3D deposition of cobalt with nanosecond voltage pulses in an STM
A feature size <100 nm for localized electrodeposition of Co on Au exceeds predictions of previous models for confined double-layer charging with ns-long voltage pulses. We show 2D patterning and demonstrate the potential for out-of-plane growth.
- 28 March 2022
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 14 (14) , 5579-5588
Open AccessNanoscale electrochemical 3D deposition of cobalt with nanosecond voltage pulses in an STM
A feature size <100 nm for localized electrodeposition of Co on Au exceeds predictions of previous models for confined double-layer charging with ns-long voltage pulses. We show 2D patterning and demonstrate the potential for out-of-plane growth.