Lars Grüner-Nielsen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lars Grüner-Nielsen has a total of 556 co-authors. Here are the top co-authors by number of shared publications:
- David John Richardson
School of Biological Sciences, University of East Anglia, Norwich Research Park, Norwich NR4 7TJ, United Kingdom
39 shared publications Karsten Rottwitt
22 shared publicationsDan Jakobsen
OFS Fitel, Denmark
20 shared publicationsY. Sun
OFS, 2000 Northeast Expressway, Norcross, GA 30071, USA
17 shared publications- Andrew D. Ellis
Aston University
15 shared publications - Michael Galili
Technical University of Denmark
15 shared publications
Latest Publications
- 22 October 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (22) , 41489
Photon-pair characterization in an amorphous silicon waveguide
We report a comprehensive characterization of photon-pair generation by spontaneous four-wave mixing in a partially deuterated amorphous silicon (a-Si:D) waveguide for C-band heralded single-photon generation. In a 3.3-mm-long strip waveguide pumped with a continuous-wave laser at telecom wavelengths, we measure an on-chip pair-generation rate of 3.1 × 10 6 pairs/s, a maximum coincidence-to-accidental ratio of 66, and a heralded second-order correlation g H (2) (0)=0.058±0.002, with these values obtained at different pump powers. We also demonstrate, to the best of our knowledge, the first observation of time-energy entanglement from an amorphous silicon waveguide, with a Franson interference visibility of 77±5%. The power scaling of the singles and accidental coincidences indicates a significant noise contribution that currently limits the source performance. Our results identify a-Si:D as a promising nonlinear platform for bright, integrated photon-pair sources and future hybrid quantum photonic circuits.
- 22 October 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (22) , 41489
Photon-pair characterization in an amorphous silicon waveguide
We report a comprehensive characterization of photon-pair generation by spontaneous four-wave mixing in a partially deuterated amorphous silicon (a-Si:D) waveguide for C-band heralded single-photon generation. In a 3.3-mm-long strip waveguide pumped with a continuous-wave laser at telecom wavelengths, we measure an on-chip pair-generation rate of 3.1 × 10 6 pairs/s, a maximum coincidence-to-accidental ratio of 66, and a heralded second-order correlation g H (2) (0)=0.058±0.002, with these values obtained at different pump powers. We also demonstrate, to the best of our knowledge, the first observation of time-energy entanglement from an amorphous silicon waveguide, with a Franson interference visibility of 77±5%. The power scaling of the singles and accidental coincidences indicates a significant noise contribution that currently limits the source performance. Our results identify a-Si:D as a promising nonlinear platform for bright, integrated photon-pair sources and future hybrid quantum photonic circuits.
- 10 August 2026
- Published by Optica Publishing Group in Optica Quantum
- Vol. 4 (4) , 382
Ultra-low-noise heralded single photons from counter-propagating SPDC
Over the past decade, counter-propagating spontaneous parametric down-conversion (CPSPDC) has attracted interest due to its ability to generate narrowband and spectrally pure photon pairs without the need for strong spectral filtering. While prior work has established the spectral characteristics of CPSPDC, its performance as a heralded single-photon source (HSPS) remains limited. Here, we present a detailed HSPS characterization of a first-order quasi-phase-matched CPSPDC source based on a sub-μm periodically poled potassium titanyl phosphate crystal. We measure an internal pair-generation rate of 1.3×10 3 pairs/s/mW under CW pumping, in addition to a high coincidence-to-accidental ratio exceeding 1.4×10 5 , and furthermore obtain the lowest heralded second-order correlation value of (8.57±4.95)×10 -6 ever reported. We also show a Hong–Ou–Mandel interference experiment that yields a raw visibility of 70±1%, confirming photon indistinguishability. These results demonstrate CPSPDC as a strong candidate for generating high-quality single photons for quantum information processing and long-distance quantum communication applications.
- 10 August 2026
- Published by Optica Publishing Group in Optica Quantum
- Vol. 4 (4) , 382
Ultra-low-noise heralded single photons from counter-propagating SPDC
Over the past decade, counter-propagating spontaneous parametric down-conversion (CPSPDC) has attracted interest due to its ability to generate narrowband and spectrally pure photon pairs without the need for strong spectral filtering. While prior work has established the spectral characteristics of CPSPDC, its performance as a heralded single-photon source (HSPS) remains limited. Here, we present a detailed HSPS characterization of a first-order quasi-phase-matched CPSPDC source based on a sub-μm periodically poled potassium titanyl phosphate crystal. We measure an internal pair-generation rate of 1.3×10 3 pairs/s/mW under CW pumping, in addition to a high coincidence-to-accidental ratio exceeding 1.4×10 5 , and furthermore obtain the lowest heralded second-order correlation value of (8.57±4.95)×10 -6 ever reported. We also show a Hong–Ou–Mandel interference experiment that yields a raw visibility of 70±1%, confirming photon indistinguishability. These results demonstrate CPSPDC as a strong candidate for generating high-quality single photons for quantum information processing and long-distance quantum communication applications.
- 1 January 2025
- Published by Optica Publishing Group
- p. M1C.3
Repeaterless Brillouin OTDR Sensing
We demonstrate a Brillouin OTDR sensing range of 250 km on a telecommunication fiber. Including a normal dispersion fiber at a selected position helps to reduce the nonlinear noise arising from modulation instability at the remote end.
- 1 January 2025
- Published by Optica Publishing Group
- p. M1C.3
Repeaterless Brillouin OTDR Sensing
We demonstrate a Brillouin OTDR sensing range of 250 km on a telecommunication fiber. Including a normal dispersion fiber at a selected position helps to reduce the nonlinear noise arising from modulation instability at the remote end.
- 2 December 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (26) , 45483-45493
Fiber-artefact methodology and calibration framework for Brillouin-based fiber sensing
We propose, and demonstrate, the use of a fiber-optical measurement artefact as a metrological tool for traceable distance calibration of distributed optical fiber sensors. The constructed fiber artefact consists of a lead-in fiber coupled to a fiber loop using a 3-dB coupler and is used to calibrate both a home-build Brillouin-OTDR setup and a custom version of a commercial Brillouin-OTDR interrogator build for distributed temperature sensing. For both interrogators, we demonstrate distance calibrations with 1-meter uncertainty (k=1) in the offset length and 0.1 % (1 m/km) uncertainty (k = 1) in the distance scale factor. In addition, it is shown that the fiber artefact can be used to assess undesired distance-dependent measurement biases.
- 2 December 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (26) , 45483-45493
Fiber-artefact methodology and calibration framework for Brillouin-based fiber sensing
We propose, and demonstrate, the use of a fiber-optical measurement artefact as a metrological tool for traceable distance calibration of distributed optical fiber sensors. The constructed fiber artefact consists of a lead-in fiber coupled to a fiber loop using a 3-dB coupler and is used to calibrate both a home-build Brillouin-OTDR setup and a custom version of a commercial Brillouin-OTDR interrogator build for distributed temperature sensing. For both interrogators, we demonstrate distance calibrations with 1-meter uncertainty (k=1) in the offset length and 0.1 % (1 m/km) uncertainty (k = 1) in the distance scale factor. In addition, it is shown that the fiber artefact can be used to assess undesired distance-dependent measurement biases.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (18) , 6286-6292
Modeling the Brillouin Spectrum in Raman Amplifier-Assisted Brillouin OTDR
A tool for increasing the range of Brillouin optical time domain reflectometry (BOTDR) is distributed in-line Raman amplification. In this article, we model and experimentally verify how a combination of Raman pump depletion, pump-probe walk-off and self- and cross-phase modulation lead to a shift of the Brillouin spectrum, ultimately inducing an error in the sensor reading. The induced error is up to approximately 7 MHz (approx. 7 °C) for standard BOTDR parameters. We numerically model the propagation of the fields in the fiber using standard propagation equations, and by considering only spontaneous Brillouin scattering as the source of the back-scattered field, we find an expression of the Brillouin spectrum. By using standard parameters of a BOTDR setup, we show how there is a tradeoff between Raman amplifier gain and the spectrally induced error. By comparing the model to experiments, we find that the measurements show the same trend as the simulated spectra.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (18) , 6286-6292
Modeling the Brillouin Spectrum in Raman Amplifier-Assisted Brillouin OTDR
A tool for increasing the range of Brillouin optical time domain reflectometry (BOTDR) is distributed in-line Raman amplification. In this article, we model and experimentally verify how a combination of Raman pump depletion, pump-probe walk-off and self- and cross-phase modulation lead to a shift of the Brillouin spectrum, ultimately inducing an error in the sensor reading. The induced error is up to approximately 7 MHz (approx. 7 °C) for standard BOTDR parameters. We numerically model the propagation of the fields in the fiber using standard propagation equations, and by considering only spontaneous Brillouin scattering as the source of the back-scattered field, we find an expression of the Brillouin spectrum. By using standard parameters of a BOTDR setup, we show how there is a tradeoff between Raman amplifier gain and the spectrally induced error. By comparing the model to experiments, we find that the measurements show the same trend as the simulated spectra.
- 16 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (5) , 1434-1442
Channel Fading-Robust Pre-Coders for Low Complexity Few-Mode IM/DD Short Reach Fiber Communications
In this paper, an autoencoder (AE) is used to optimize linear and nonlinear digital pre-coders for short reach few-mode fiber transmission. Mach-Zehnder modulation is used to modulate the intensity of the optical carriers, and direct detection is employed at the receiver. The modes are (de)multiplexed using photonic lanterns with air cladding. The AEs are optimized to be robust against cross-talk (XT) and distance variations, which result in time varying power fading across the different modes. The system is exemplified using a simulation of a graded index fiber with the mode groups $LP_{01}$ and $LP_{11}$ used for data transmission. The channel and (de)multiplexer XT parameters and fading distributions are obtained from experimental measurements. In the case of unknown distance, the distance-robust pre-coding allows for on-off keying transmission with an error rate below the chosen forward error correction threshold even at severe XT expectations and variations. In the case of a fixed-length system, pre-coding enables high order modulation such as 4PAM and 8PAM. In this case, nonlinear pre-coding achieves signal-to-noise ratio gains of up to 1.5 dB w.r.t. linear pre-coding and up to 4 dB w.r.t. simple power pre-emphasis.
- 16 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (5) , 1434-1442
Channel Fading-Robust Pre-Coders for Low Complexity Few-Mode IM/DD Short Reach Fiber Communications
In this paper, an autoencoder (AE) is used to optimize linear and nonlinear digital pre-coders for short reach few-mode fiber transmission. Mach-Zehnder modulation is used to modulate the intensity of the optical carriers, and direct detection is employed at the receiver. The modes are (de)multiplexed using photonic lanterns with air cladding. The AEs are optimized to be robust against cross-talk (XT) and distance variations, which result in time varying power fading across the different modes. The system is exemplified using a simulation of a graded index fiber with the mode groups $LP_{01}$ and $LP_{11}$ used for data transmission. The channel and (de)multiplexer XT parameters and fading distributions are obtained from experimental measurements. In the case of unknown distance, the distance-robust pre-coding allows for on-off keying transmission with an error rate below the chosen forward error correction threshold even at severe XT expectations and variations. In the case of a fixed-length system, pre-coding enables high order modulation such as 4PAM and 8PAM. In this case, nonlinear pre-coding achieves signal-to-noise ratio gains of up to 1.5 dB w.r.t. linear pre-coding and up to 4 dB w.r.t. simple power pre-emphasis.
- 21 March 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (7) , 11457-11470
Mitigating probe pulse deformation in Raman amplification in OTDR fiber sensing systems
We report the numerical and experimental study of probe pulse deformation in a forward-pumped distributed Raman amplifier on a 40-km standard single mode fiber. Distributed Raman amplification can improve the range of OTDR-based sensing systems, but it could result in pulse deformation. A smaller Raman gain coefficient can be used to mitigate pulse deformation. The sensing performance can still be maintained by compensating for the decrease in the Raman gain coefficient by increasing the pump power. The tunability of the Raman gain coefficient and pump power levels are predicted while keeping the probe power below the modulation instability limit.
- 21 March 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (7) , 11457-11470
Mitigating probe pulse deformation in Raman amplification in OTDR fiber sensing systems
We report the numerical and experimental study of probe pulse deformation in a forward-pumped distributed Raman amplifier on a 40-km standard single mode fiber. Distributed Raman amplification can improve the range of OTDR-based sensing systems, but it could result in pulse deformation. A smaller Raman gain coefficient can be used to mitigate pulse deformation. The sensing performance can still be maintained by compensating for the decrease in the Raman gain coefficient by increasing the pump power. The tunability of the Raman gain coefficient and pump power levels are predicted while keeping the probe power below the modulation instability limit.
- 3 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (11) , 571-574
A Converter for Transmission With Singlemode Performance on OM2/3/4/5 Multimode Fibers
A converter from a singlemode fiber to the fundamental mode of an OM2, OM3, OM4, or OM5 type multimode fiber is presented and is used to transmit 100 GbE with no detected errors over 1600 m multimode fiber using commercial transceivers. The converter is based on splicing a short length of few-mode fiber between the singlemode fiber and the multimode fiber. The few-mode fiber is designed so that the fundamental mode of the few-mode fiber has a good mode overlap with the fundamental mode of the multimode fiber. To suppress any higher order modes in the few-mode fiber, an optimized bend based mode stripper is used. The converter has a low loss of 0.35 dB, lower than previous reported solution. The converter do, opposite to previous suggested solutions, not include any free space part or mechanical connections, which assures low loss and cross talk as well as good long term stability.
- 3 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (11) , 571-574
A Converter for Transmission With Singlemode Performance on OM2/3/4/5 Multimode Fibers
A converter from a singlemode fiber to the fundamental mode of an OM2, OM3, OM4, or OM5 type multimode fiber is presented and is used to transmit 100 GbE with no detected errors over 1600 m multimode fiber using commercial transceivers. The converter is based on splicing a short length of few-mode fiber between the singlemode fiber and the multimode fiber. The few-mode fiber is designed so that the fundamental mode of the few-mode fiber has a good mode overlap with the fundamental mode of the multimode fiber. To suppress any higher order modes in the few-mode fiber, an optimized bend based mode stripper is used. The converter has a low loss of 0.35 dB, lower than previous reported solution. The converter do, opposite to previous suggested solutions, not include any free space part or mechanical connections, which assures low loss and cross talk as well as good long term stability.
- 20 April 2022
- Published by IOP Publishing in Journal of Optics
- Vol. 24 (5) , 054011
Air-clad photonic lanterns: fabrication and applications
The fabrication steps for an air-clad photonic lantern that can excite the first two LP mode groups in a multimode fiber are presented in this paper. A multiplexing crosstalk below −16.8 dB is measured on the fabricated lantern using S 2 imaging technique over a wavelength of 1525–1575 nm. The de-multiplexing crosstalk is measured for both LP 01 and LP 11 mode groups as −16.8 dB and −9.4 dB respectively using loss measurements. 2 × 40 Gbs −1 MIMO-less mode division multiplexing (MDM) transmission through 7 m of two mode step index fiber is demonstrated using the fabricated photonic lanterns. 2 × 10 Gbs −1 MIMO-less MDM transmission through 1.6 km standard 50/125 µ m multimode fiber is also demonstrated and a Q value higher than 3.7 is obtained for both spatial channels over all input polarizations. Simple intensity modulation and direct detection schemes are used for these MDM transmissions.
- 20 April 2022
- Published by IOP Publishing in Journal of Optics
- Vol. 24 (5) , 054011
Air-clad photonic lanterns: fabrication and applications
The fabrication steps for an air-clad photonic lantern that can excite the first two LP mode groups in a multimode fiber are presented in this paper. A multiplexing crosstalk below −16.8 dB is measured on the fabricated lantern using S 2 imaging technique over a wavelength of 1525–1575 nm. The de-multiplexing crosstalk is measured for both LP 01 and LP 11 mode groups as −16.8 dB and −9.4 dB respectively using loss measurements. 2 × 40 Gbs −1 MIMO-less mode division multiplexing (MDM) transmission through 7 m of two mode step index fiber is demonstrated using the fabricated photonic lanterns. 2 × 10 Gbs −1 MIMO-less MDM transmission through 1.6 km standard 50/125 µ m multimode fiber is also demonstrated and a Q value higher than 3.7 is obtained for both spatial channels over all input polarizations. Simple intensity modulation and direct detection schemes are used for these MDM transmissions.
- Open Access
- 29 March 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (8) , 12474-12483
Electrooptic control of the modal distribution in a silicate fiber
We demonstrate the use of the electrooptic effect to control the propagation constant of the guided modes in silicate few mode fibers with internal electrodes. The electrooptic effect induces a perturbation of the fiber’s refractive index profile that controls intermodal interference. To increase the electrooptic effect the silicate fibers are poled. The response time is in the nanosecond range.
- 29 March 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (8) , 12474-12483
Open AccessElectrooptic control of the modal distribution in a silicate fiber
We demonstrate the use of the electrooptic effect to control the propagation constant of the guided modes in silicate few mode fibers with internal electrodes. The electrooptic effect induces a perturbation of the fiber’s refractive index profile that controls intermodal interference. To increase the electrooptic effect the silicate fibers are poled. The response time is in the nanosecond range.