JBJoey R. Bray

Joey R. Bray

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Joey R. Bray has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Backscatter Radar Cross Section Analysis of Chaff Using the Sequential Loading Method

    by Husam Osman, Joey R. Bray

    A new method of computing the radar cross section (RCS) of chaff particles and spherical chaff clouds is proposed using the Sequential Loading Method (SLM). For the first time, the SLM has been used to compute the RCS of chaff particles for any aspect angle and polarization, over a broad range of lengths and frequencies, including resistive loss. One of the advantages of the SLM is its speed: in this work, the SLM computes the current flowing on a chaff particle from 2 to 29.5 GHz at least 80-times faster than a Method of Moments (MoM) solution. A new spherical chaff cloud shielding model based on the SLM is then presented to rapidly compute the chaff cloud RCS as a function of its density. The results show that shielding, in addition to mutual coupling, is responsible for the nonlinear departure of the cloud’s RCS as a function of its density. A new rule based on the optical depth parameter is proposed to consistently estimate the upper density limit at which shielding becomes significant.


  • Antenna Design and Analysis Using the Sequential Loading Method

    by Husam Osman, Joey R. Bray

    This paper presents a new method of accurately designing and analyzing an antenna or array. The proposed technique operates solely on the transfer admittance matrix of a perfect electrically conducting antenna fabric that is obtained using a full-wave simulator only once. The desired antenna, which must be a subset of the fabric, is then synthesized by progressively loading the fabric and applying a computationally efficient iterative post-processing technique that transforms the stored admittance matrix into one that corresponds to the desired antenna or array. Given that the admittance matrix of the fabric is used as the basis for all subsequent antennas that can be represented by the fabric, it contains the solutions to an entire class of antennas. The proposed method is demonstrated by applying it to the class of co-linear antennas up to five wavelengths long, arranged along a single axis. The method is validated by comparing its results to those obtained using a conventional full-wave simulator. The proposed method is applied first to the case of multiple loads located at arbitrary port locations along the fabric. Then, open-circuited loads are used to decimate the tips of a linear antenna to demonstrate that the method accurately predicts the response of an electrically shorter antenna. Finally, decimation is used to transform the fabric into an array of smaller antennas, where it is shown that mutual coupling effects are accurately predicted.


  • Open Access

    Understanding Digital Radio Frequency Memory Performance in Countermeasure Design

    by Kyle Davidson, Joey Bray

    This paper describes the design, implementation, and testing of a novel multi-function software defined Radio Frequency (RF) system designed for small airborne drone applications. The system was created using an inexpensive Field Programmable Gate Array (FPGA) to combine a coherent linear frequency modulated radar transmitter and receiver, with a Digital Radio Frequency Memory (DRFM) jammer for use with a common RF aperture in simultaneous operation. The system was implemented on a Xilinx Kintex-7 FPGA with a wideband analogue-to-digital/ digital-to-analogue (ADC/DAC) converter mezzanine board and tested using hardware-in-the-loop mode to validate its performance. This is the first known account of an integrated multifunction electronic attack and radar system on a single chip, capable of performing a simultaneous, not time shared, operation.


  • Open Access

    Theory and Design of Blink Jamming

    by Kyle Davidson, Joey Bray

    Establishing an error in the angle estimates of a monopulse radar is critical to creating miss distance during the terminal stage of missile engagements. However, the tools for creating angle deception are limited, with blink jamming offering significant potential. This paper fills in the conceptual gaps in understanding of blink jamming, through a theoretical analysis, which is validated using modelling and simulation, including hardware-in-the-loop with a Field Programmable Gate Array (FPGA). Additionally, a novel version of blink jamming is proposed, using a synchronized amplitude modulation, and its performance compared to traditional, unmodulated blink jamming. The complete results are discussed, with design guidance provided for implementing blink jamming in operational scenarios.


  • Open Access

    MIMO Radar Using a Vector Network Analyzer

    by Mostafa Hefnawi, Joey Bray, Jonathan Bathurst, Yahia Antar

    In this paper, a multiple-input multiple-output (MIMO) radar system was developed using a Keysight’s N5244A 4-port PNA-X network analyzer and Simulink. The system can transmit and receive TDM stepped-frequency continuous wave signals with a total sweep bandwidth of 450 MHz. The system also provides a reliable, self-contained phase-coherent RF front-end across four RF channels, which is a critical requirement for MIMO Radar signal processing algorithms. A Simulink model was built to organize the collected S-parameters into a virtual array and to perform IFFT processing so that range and angle information from targets could be extracted. The experimental results show the ability of the MIMO radar to distinguish between multiple closely spaced targets with a 33 cm range resolution and a 19o angle resolution.


  • Synthesis of Wire Antennas Using the Multipole Expansion Method

    by Husam Osman, Abdelelah Alzahed, Joey R. Bray, Said M. Mikki, Yahia M. M. Antar

    A rigorous mathematical solution to the problem of synthesizing wire antennas using the multipole expansion method (MEM) is presented. The input current and required size of the antenna are estimated using the knowledge of the required field pattern. This solution is based on three steps. First, obtaining the expansion’s weighting coefficients that carry both the signature of the current and size of the antenna. In essence, the analysis of the direct modelling needs to be addressed first in order to define these coefficients. Second, extracting the coefficients from the required field pattern using the natural orthogonality property of the spherical harmonic functions. Finally, performing a numerical search for the argument of the spherical Bessel functions to satisfy the ratio between two successive moments. Once the size of the antenna is found, a recursive expression is used to obtain the input current. For the current distributions assumed herein, the odd order coefficients of the MEM are shown to be the only necessary coefficients to construct the radiation far field. Also, it is found that the estimated model parameters are in excellent agreement with the analytical ones.


  • An Improved Antenna Scattering Model: An equivalent model based on the reciprocity theorem

    by Joey R. Bray

    The Thévenin and Norton equivalent models of a receiving antenna cannot be used to calculate the antenna's scattered power because they are too simplistic. Based on the reciprocity theorem, a more elaborate equivalent model, consisting of a passive distributed transformer, is proposed for wire antennas in both the transmit and receive modes. The model parameters are derived from the antenna's transfer admittance parameters, the latter obtained under short circuit loading conditions in transmit mode only. A method is then applied to determine the new admittance parameters when the antenna is perturbed by an arbitrary load, which allows the receive-mode current distribution on the antenna to be calculated. Once the receive-mode current is known,scattered power can be calculated with a formula that avoids integration over the far-field sphere. The method has been applied to a λ/2dipole, λ-dipole, and three-element Yagi antenna for resistive loads spanning up to nine decades. Calculated scattered-power values are shown to agree almost perfectly with values obtained using a commercial simulator, thus demonstrating that it is possible to calculate scattered power based on the characterization of the antenna in transmit mode only. Results indicate that the aperture efficiency of a dipole antenna can exceed 50% when it is connected to a mismatched load. Finally, a newly defined transducer efficiency is presented, which can be used to choose an optimum load to obtain the best compromise between the aperture and scattering areas.


  • Design and Evaluation of Test Waveforms Emitted by Portable Electronic Devices for Radiated Susceptibility Testing of Avionic Systems

    by Samuel Blanchette, Joey R. Bray, Yahia M. M. Antar

    Assessing the electromagnetic interference (EMI) susceptibility of aircraft systems to transmitting portable electronic devices is challenging. Existing waveforms for susceptibility testing use amplitude modulation: MIL-STD-461 recommends the use of pulse-modulated waveforms, whereas the radio technical commission for aeronautics recommends the use of filtered noise. The ability of such waveforms to represent the EMI of complex communication signals is unknown. This paper expands upon a parameter reduction process for the development of candidate waveforms that are representative of long-term evolution (LTE) signals: single-carrier frequency division multiple access, filtered noise, and pulsemodulated waveforms are proposed as candidate signals for radiated susceptibility testing. The waveforms were evaluated by measuring the EMI response of avionic equipment that was exposed to the waveforms in an anechoic chamber. The measured data were analyzed to determine whether the bandwidth and the peak-to-average power ratio had significant effects on the measured EMI compared to real LTE signals. The proposed method is general and can be used for other communication standards.