Kexiao Bi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kexiao Bi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Fantao Kong
School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Ning Cui
School of Mechanical and Automotive Engineering, Qingdao University of Technology, Qingdao 266520, China
2 shared publications - Qianqian Wu
School of Mechanical and Automotive Engineering, Qingdao University of Technology, Shandong, China
2 shared publications - Tiewei Xu
School of Mechanical and Automotive Engineering, Qingdao University of Technology, Qingdao, China
2 shared publications - Jin Wang
School of Mechanical and Automotive Engineering, Qingdao University of Technology, Qingdao, China
1 shared publication
Latest Publications
- Open Access
Effect of Heat Treatment on Microstructures and Mechanical Properties of a Novel β-Solidifying TiAl Alloy
The effect of heat treatment on the microstructures and mechanical properties of a novel β-solidifying Ti–43Al–2Cr–2Mn–0.2Y alloy was investigated. A fully lamellar (FL) microstructure with a colony size of about 100 μm was obtained by heat treatment at 1320 °C/10 min/furnace cooling (FC). A duplex (DP) microstructure with globular γ grains and γ/α2 lamellae was obtained by heat treatment at 1250 °C/4 h/FC. The residual hard–brittle β0 phase was also eliminated after heat treatment. The mechanical properties of the β-solidifying TiAl alloy depended closely on the heat treatment. The FL alloy had better fracture toughness, and the fracture toughness (KIC) value was 24.15 MPa·m1/2. The DP alloy exhibited better ductility, and the room temperature (RT) elongation of the alloy could reach 1%. The elongation of the alloy with different microstructures sharply increased when the temperature increased from 700 to 750 °C, indicating that the microstructure had no effect on the ductile–brittle transition temperature of the β-solidifying TiAl alloy. The fracture morphologies of different tensile specimens were observed. Interlamellar and translamellar fractures were the main fracture features of the FL alloy. Intergranular, translamellar, and interlamellar fractures were the main fracture features of the DP alloy.
Open AccessEffect of Heat Treatment on Microstructures and Mechanical Properties of a Novel β-Solidifying TiAl Alloy
The effect of heat treatment on the microstructures and mechanical properties of a novel β-solidifying Ti–43Al–2Cr–2Mn–0.2Y alloy was investigated. A fully lamellar (FL) microstructure with a colony size of about 100 μm was obtained by heat treatment at 1320 °C/10 min/furnace cooling (FC). A duplex (DP) microstructure with globular γ grains and γ/α2 lamellae was obtained by heat treatment at 1250 °C/4 h/FC. The residual hard–brittle β0 phase was also eliminated after heat treatment. The mechanical properties of the β-solidifying TiAl alloy depended closely on the heat treatment. The FL alloy had better fracture toughness, and the fracture toughness (KIC) value was 24.15 MPa·m1/2. The DP alloy exhibited better ductility, and the room temperature (RT) elongation of the alloy could reach 1%. The elongation of the alloy with different microstructures sharply increased when the temperature increased from 700 to 750 °C, indicating that the microstructure had no effect on the ductile–brittle transition temperature of the β-solidifying TiAl alloy. The fracture morphologies of different tensile specimens were observed. Interlamellar and translamellar fractures were the main fracture features of the FL alloy. Intergranular, translamellar, and interlamellar fractures were the main fracture features of the DP alloy.
- Open Access
Effect of Multi-Directional Forging on the Microstructure and Mechanical Properties of β-Solidifying TiAl Alloy
This study systematically investigated the influence of multi-directional forging (MDF) on the microstructural evolution, hot deformation behavior, and tensile properties of a β-solidifying TiAl alloy. The initial lamellar microstructure of an as-cast alloy was remarkably refined and homogenized by three-step MDF. High temperatures and multi-pass deformations were conducive to the decomposition of lamellae. A crack-free billet was obtained through three-step MDF, with a deformation temperature of 1250 °C and a forging speed of 0.1 mm/s, indicating that MDF can be applied to β-solidifying TiAl alloys by the proper control of the alloy composition and process parameters. Microstructural observation showed that the billet mainly consists of fine and equiaxed γ grains and a small amount of β phase. The tensile properties of the multi-directional forged alloy were also significantly improved, due to microstructure refinement. The ultimate tensile strength (UTS) and elongation (δ) at room temperature were 689.4 MPa, and 0.83%, respectively. The alloy exhibits excellent ductility at 700 °C. When the temperature was increased to 700 °C, the UTS decreased to 556 MPa and δ increased to 5.98%, indicating that the alloy exhibits excellent ductility at 700 °C. As the temperature further increased to 750 °C, δ dramatically increased to 46.65%, indicating that the ductile-brittle transition temperature of the alloy is between 700 °C and 750 °C.
Open AccessEffect of Multi-Directional Forging on the Microstructure and Mechanical Properties of β-Solidifying TiAl Alloy
This study systematically investigated the influence of multi-directional forging (MDF) on the microstructural evolution, hot deformation behavior, and tensile properties of a β-solidifying TiAl alloy. The initial lamellar microstructure of an as-cast alloy was remarkably refined and homogenized by three-step MDF. High temperatures and multi-pass deformations were conducive to the decomposition of lamellae. A crack-free billet was obtained through three-step MDF, with a deformation temperature of 1250 °C and a forging speed of 0.1 mm/s, indicating that MDF can be applied to β-solidifying TiAl alloys by the proper control of the alloy composition and process parameters. Microstructural observation showed that the billet mainly consists of fine and equiaxed γ grains and a small amount of β phase. The tensile properties of the multi-directional forged alloy were also significantly improved, due to microstructure refinement. The ultimate tensile strength (UTS) and elongation (δ) at room temperature were 689.4 MPa, and 0.83%, respectively. The alloy exhibits excellent ductility at 700 °C. When the temperature was increased to 700 °C, the UTS decreased to 556 MPa and δ increased to 5.98%, indicating that the alloy exhibits excellent ductility at 700 °C. As the temperature further increased to 750 °C, δ dramatically increased to 46.65%, indicating that the ductile-brittle transition temperature of the alloy is between 700 °C and 750 °C.