Xiaomeng Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiaomeng Li has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Yunjun Luo
School of Materials Science and Technology, Beijing Institute of Technology, Beijing 100081, China
3 shared publications - Xiaoqing Wang
School of Materials Science & Engineering, Beijing Institute of Technology, Beijing 100081, China
2 shared publications - Bo Chen
National Engineering Research Center for Flame Retardant Materials, School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081, China
1 shared publication - Chang Liu
Beijing Institute of Technology, School of Materials Science and Engineering, Beijing 100081, China
1 shared publication - Chenyang Yan
National Enginneering Research Center for Flame Retardant Materials, School of Materials Science & Engineering, Beijing Institute of Technology, 5 Zhongguancun South Street, Haidian District, Beijing 100081, China
1 shared publication - Guoping Li
School of Materials Science & Engineering, Beijing Institute of Technology, Beijing 100081, China
1 shared publication
Latest Publications
- Open Access
Silicon Hybrid EPDM Composite with High Thermal Protection Performance
The effects of octaphenylsilsesquioxane (OPS), fumed silica, and silica aerogel on the thermal insulation properties of ethylene propylene diene monomer (EPDM) rubber were studied. On this basis, two kinds of fillers with good performances were selected to study the thermal insulation of an EPDM full-formula system. The results show that the addition of fumed silica or silica aerogel had a positive effect on the thermal insulation performance of EPDM rubber and its composite. A 30 wt% silica aerogel can be well dispersed in the EPDM rubber system and with a lower thermal conductivity compared with fumed silica. EPDM composite with 23.4 wt% fumed silica can produce more char residues at 1000 °C than at 500 °C in a burn-through test and formed the compact and porous char at 1000 °C, which had a lowest thermal conductivity. EPDM composite with fumed silica cannot be burned through 1000 °C burning, and comparison with silica aerogel revealed that it achieved the lowest back temperature and had a temperature of 388 °C after 800 s.
Open AccessSilicon Hybrid EPDM Composite with High Thermal Protection Performance
The effects of octaphenylsilsesquioxane (OPS), fumed silica, and silica aerogel on the thermal insulation properties of ethylene propylene diene monomer (EPDM) rubber were studied. On this basis, two kinds of fillers with good performances were selected to study the thermal insulation of an EPDM full-formula system. The results show that the addition of fumed silica or silica aerogel had a positive effect on the thermal insulation performance of EPDM rubber and its composite. A 30 wt% silica aerogel can be well dispersed in the EPDM rubber system and with a lower thermal conductivity compared with fumed silica. EPDM composite with 23.4 wt% fumed silica can produce more char residues at 1000 °C than at 500 °C in a burn-through test and formed the compact and porous char at 1000 °C, which had a lowest thermal conductivity. EPDM composite with fumed silica cannot be burned through 1000 °C burning, and comparison with silica aerogel revealed that it achieved the lowest back temperature and had a temperature of 388 °C after 800 s.
- Open Access
Tribological and Mechanical Applications of Liquid-Crystal-Polymer-Modified Carbon-Fiber-Reinforced Polyamide–Polyurethane Composites
An aromatic copolyester liquid crystal polymer (LCP) was introduced into carbon-fiber-reinforced polyamide–polyurethane (CF/PA-PU) composites through melt blending to improve the tribological properties of the composites. The effects of LCP on the mechanical, processing, and thermal properties of CF/PA-PU composites were compared to those of commonly-used graphite (Gr). The results showed that at 5 wt.% LCP content, the coefficient of friction (COF) was decreased by 16.06%, and the wear rate by 32.22% in the LCP/CF/PA-PU composite compared to the CF/PA-PU composite. Furthermore, using LCP instead of Gr showed significantly improved mechanical properties and reduced processing viscosity. The tensile strength of 5%LCP/CF/PA-PU composite could reach 99.08 MPa, while the equilibrium torque was reduced, being 26.85% higher and 18.37% lower than those of CF/PA-PU composite, respectively. The thermal stability of LCP/CF/PA-PU composites was also enhanced. The addition of 5 wt.% LCP to CF/PA-PU composite increased the initial decomposition temperature by 14.19% compared to CF/PA-PU. In sharp contrast, the addition of Gr increased equilibrium torque and actual processing temperature leading to processing difficulties and instability. This approach offers a novel strategy for tribological applications and tackles the problem of high viscosity in CF/PA-PU composites.
Open AccessTribological and Mechanical Applications of Liquid-Crystal-Polymer-Modified Carbon-Fiber-Reinforced Polyamide–Polyurethane Composites
An aromatic copolyester liquid crystal polymer (LCP) was introduced into carbon-fiber-reinforced polyamide–polyurethane (CF/PA-PU) composites through melt blending to improve the tribological properties of the composites. The effects of LCP on the mechanical, processing, and thermal properties of CF/PA-PU composites were compared to those of commonly-used graphite (Gr). The results showed that at 5 wt.% LCP content, the coefficient of friction (COF) was decreased by 16.06%, and the wear rate by 32.22% in the LCP/CF/PA-PU composite compared to the CF/PA-PU composite. Furthermore, using LCP instead of Gr showed significantly improved mechanical properties and reduced processing viscosity. The tensile strength of 5%LCP/CF/PA-PU composite could reach 99.08 MPa, while the equilibrium torque was reduced, being 26.85% higher and 18.37% lower than those of CF/PA-PU composite, respectively. The thermal stability of LCP/CF/PA-PU composites was also enhanced. The addition of 5 wt.% LCP to CF/PA-PU composite increased the initial decomposition temperature by 14.19% compared to CF/PA-PU. In sharp contrast, the addition of Gr increased equilibrium torque and actual processing temperature leading to processing difficulties and instability. This approach offers a novel strategy for tribological applications and tackles the problem of high viscosity in CF/PA-PU composites.
- Open Access
Study on GAP Adhesive-Based Polymer Films, Energetic Polymer Composites and Application
To lay the foundation for environmentally friendly energetic polymer composites, GAP (glycidyl azide polymer) adhesive-based polymer films with different curing parameter R (mol ratio of hydroxyl/isocyanate) and energetic polymer composites with different RDX contents were studied. GAP/TDI (toluene diisocyanate)/GLY(glycerol) was selected as the adhesive system. The tensile strength and elongation at the break of the polymer film with R = 2.2, was 14.34 MPa and 176.86%, respectively, as observed by an AGS-J electronic universal testing machine. A relatively complete cross-linking network and high hydrogen bonding interaction were observed by LF-NMR (low-field nuclear magnetic resonance, where the cross-linking density was 11.06 × 10−4 mol/cm3) and FT-IR (fourier transform infrared spectroscopy, where the carbonyl bonding ratio was 64.84%). Forty percent RDX(hexogen) was added into the adhesive system. The tensile strength was 4.65 MPa, and the elongation at the break was 78.49%; meanwhile, the heat of the explosive was 2.87 MJ/kg, and the residue carbon rate was only 2.47%. The tensile cross-sections of energetic polymer composites were observed by SEM (Scanning electron microscopy).
Open AccessStudy on GAP Adhesive-Based Polymer Films, Energetic Polymer Composites and Application
To lay the foundation for environmentally friendly energetic polymer composites, GAP (glycidyl azide polymer) adhesive-based polymer films with different curing parameter R (mol ratio of hydroxyl/isocyanate) and energetic polymer composites with different RDX contents were studied. GAP/TDI (toluene diisocyanate)/GLY(glycerol) was selected as the adhesive system. The tensile strength and elongation at the break of the polymer film with R = 2.2, was 14.34 MPa and 176.86%, respectively, as observed by an AGS-J electronic universal testing machine. A relatively complete cross-linking network and high hydrogen bonding interaction were observed by LF-NMR (low-field nuclear magnetic resonance, where the cross-linking density was 11.06 × 10−4 mol/cm3) and FT-IR (fourier transform infrared spectroscopy, where the carbonyl bonding ratio was 64.84%). Forty percent RDX(hexogen) was added into the adhesive system. The tensile strength was 4.65 MPa, and the elongation at the break was 78.49%; meanwhile, the heat of the explosive was 2.87 MJ/kg, and the residue carbon rate was only 2.47%. The tensile cross-sections of energetic polymer composites were observed by SEM (Scanning electron microscopy).
- 11 June 2019
- Published by Taylor & Francis in Soft Materials
- Vol. 17 (4) , 427-436
Preparation and characterization of polybutadiene curing system by click chemistry
Polybutadiene curing systems from propargyl-terminal polybutadiene (PTPB), triazide acetate propane (TAP) and terminal azido polyethylene glycol (APEG) were prepared via the 1,3-dipolar cycloaddition reaction between azido and propargyl groups. By systematically tuning the ratio between TAP and APEG from 0.5 to 6.0, a series of elastomers were prepared and characterized. It was found that at a ratio TAP:APEG of 2.0, the tensile strength of the elastomer is 1.35 MPa, and the elongation at break is as high as 243%. The elongation at break was increased by 835% without the reduction of tensile strength compared to the ones with only TAP as curing agent. In addition, increasing the molecular weight of APEG from 200 g mol−1 to 1000 g mol−1 can improve the mechanical properties of elastomer, and the optimal comprehensive mechanical properties and preparation process were achieved with APEG600.
- 11 June 2019
- Published by Taylor & Francis in Soft Materials
- Vol. 17 (4) , 427-436
Preparation and characterization of polybutadiene curing system by click chemistry
Polybutadiene curing systems from propargyl-terminal polybutadiene (PTPB), triazide acetate propane (TAP) and terminal azido polyethylene glycol (APEG) were prepared via the 1,3-dipolar cycloaddition reaction between azido and propargyl groups. By systematically tuning the ratio between TAP and APEG from 0.5 to 6.0, a series of elastomers were prepared and characterized. It was found that at a ratio TAP:APEG of 2.0, the tensile strength of the elastomer is 1.35 MPa, and the elongation at break is as high as 243%. The elongation at break was increased by 835% without the reduction of tensile strength compared to the ones with only TAP as curing agent. In addition, increasing the molecular weight of APEG from 200 g mol−1 to 1000 g mol−1 can improve the mechanical properties of elastomer, and the optimal comprehensive mechanical properties and preparation process were achieved with APEG600.
- Open Access
Study of the Interfacial Interaction Performance of Branched Bonding Agents and CL-20
Adding bonding agents to the formulation is an effective way to solve the dewetting of 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) in the binder matrix. For the design and selection of the structure of a bonding agent suitable for CL-20, a series of branched polyether bonding agents with terminal groups substituted by cyano, ester and hydroxyl functional groups were employed. Contact angle, Fourier transform infrared spectra (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements were performed, and the results were compared with that of common bonding agent, the boron trifluoride triethanolamine complex (TEA·BF3). The results revealed that the nitramine reinforcement of the three polar groups to CL-20 was in the order cyano group > hydroxyl group > ester group. It is proposed that CBPE-10,10 (cyano-terminated branched polyether bonding agent) had the strongest interfacial interaction with CL-20. The adhesion work value was 105.37 mN⋅m−1 and the adhesion degree was 41.04%. The bonding properties of CBPEs/CL-20 were better than those of TEA·BF3/CL-20.
Open AccessStudy of the Interfacial Interaction Performance of Branched Bonding Agents and CL-20
Adding bonding agents to the formulation is an effective way to solve the dewetting of 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) in the binder matrix. For the design and selection of the structure of a bonding agent suitable for CL-20, a series of branched polyether bonding agents with terminal groups substituted by cyano, ester and hydroxyl functional groups were employed. Contact angle, Fourier transform infrared spectra (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements were performed, and the results were compared with that of common bonding agent, the boron trifluoride triethanolamine complex (TEA·BF3). The results revealed that the nitramine reinforcement of the three polar groups to CL-20 was in the order cyano group > hydroxyl group > ester group. It is proposed that CBPE-10,10 (cyano-terminated branched polyether bonding agent) had the strongest interfacial interaction with CL-20. The adhesion work value was 105.37 mN⋅m−1 and the adhesion degree was 41.04%. The bonding properties of CBPEs/CL-20 were better than those of TEA·BF3/CL-20.