Siyu Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Siyu Yang has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Gabriel Alfonso Rincón-Mora
School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0250, USA
2 shared publications Gabriel A. Rincon-Mora
1 shared publication
Latest Publications
- 7 September 2022
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 113 (3) , 403-414
Recycling piezoelectric switch-inductor charger
- 7 September 2022
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 113 (3) , 403-414
Recycling piezoelectric switch-inductor charger
- 1 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (4) , 1248-1252
Efficient Power Transfers in Piezoelectric Energy-Harvesting Switched-Inductor Chargers
Piezoelectric energy-harvesting transducers can draw power from motion that can be used to energize a host of wireless microsystems that sense, process, and share vital information across a network. Since these tiny devices draw little power, maximizing the power they transfer is critical. Synchronized-discharge circuits are popular in this space because they can collect all the charge from the transducer and increase drawn power. Pre-charging the transducer can draw even more power, but only as much as voltage-breakdown limits allow. This paper examines how synchronous discharge circuits can output the most power possible from tiny difficultto-overdamp piezoelectric transducers. Measurements will show how pre-charge symmetry and energy-transfer schemes alter the power drawn from the transducer and the power lost in the system. The charges are tested with a 10 × 50 × 1-mm3 15-nF transducer generates up to 10 μA at 100 Hz and the breakdown voltage of the harvester circuit is 3 V. Indirect and direct transfers with symmetric pre-charges output 21% and 43% more power with the same inductor than the 4.2 μW that indirect transfers without pre-charge can generate. Generating the highest power possible is important because, with more power, tiny piezoelectric transducers can power wireless microsensors with greater functionality and longer lifetime.
- 1 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (4) , 1248-1252
Efficient Power Transfers in Piezoelectric Energy-Harvesting Switched-Inductor Chargers
Piezoelectric energy-harvesting transducers can draw power from motion that can be used to energize a host of wireless microsystems that sense, process, and share vital information across a network. Since these tiny devices draw little power, maximizing the power they transfer is critical. Synchronized-discharge circuits are popular in this space because they can collect all the charge from the transducer and increase drawn power. Pre-charging the transducer can draw even more power, but only as much as voltage-breakdown limits allow. This paper examines how synchronous discharge circuits can output the most power possible from tiny difficultto-overdamp piezoelectric transducers. Measurements will show how pre-charge symmetry and energy-transfer schemes alter the power drawn from the transducer and the power lost in the system. The charges are tested with a 10 × 50 × 1-mm3 15-nF transducer generates up to 10 μA at 100 Hz and the breakdown voltage of the harvester circuit is 3 V. Indirect and direct transfers with symmetric pre-charges output 21% and 43% more power with the same inductor than the 4.2 μW that indirect transfers without pre-charge can generate. Generating the highest power possible is important because, with more power, tiny piezoelectric transducers can power wireless microsensors with greater functionality and longer lifetime.
- 8 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (7) , 6489-6497
Energy-Harvesting Piezoelectric-Powered CMOS Series Switched-Inductor Bridge
Tiny piezoelectric transducers transform a very small fraction of ambient energy into electrical power. Power losses and breakdown voltages unfortunately limit how much of this power reaches the microsystem. The piezoelectric harvester presented here operates at the maximum power point (MPP) without the separate MPP stage that typical piezoelectric harvesters need. As a result, the system loses less power and occupies less space. Plus, with only four transistors, the charger increases the voltage with which the piezoelectric current generates power. This way, the harvester draws more power from vibrations. By pre-charging the transducer between half cycles, the 0.81-1.2- $\mu$ m CMOS system outputs 0.7-49 $\mu$ W of the 1.2-55 μW that a vibrating 16.8-nF transducer avails at 120 Hz. This is up to 6.8 $\times$ more power than a lossless diode bridge can harness and as much as the best recycling bridge can output, but with four fewer power switches and without a separate maximum power-point stage.- 8 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (7) , 6489-6497
Energy-Harvesting Piezoelectric-Powered CMOS Series Switched-Inductor Bridge
Tiny piezoelectric transducers transform a very small fraction of ambient energy into electrical power. Power losses and breakdown voltages unfortunately limit how much of this power reaches the microsystem. The piezoelectric harvester presented here operates at the maximum power point (MPP) without the separate MPP stage that typical piezoelectric harvesters need. As a result, the system loses less power and occupies less space. Plus, with only four transistors, the charger increases the voltage with which the piezoelectric current generates power. This way, the harvester draws more power from vibrations. By pre-charging the transducer between half cycles, the 0.81-1.2- $\mu$ m CMOS system outputs 0.7-49 $\mu$ W of the 1.2-55 μW that a vibrating 16.8-nF transducer avails at 120 Hz. This is up to 6.8 $\times$ more power than a lossless diode bridge can harness and as much as the best recycling bridge can output, but with four fewer power switches and without a separate maximum power-point stage.