Guangsheng Zeng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Guangsheng Zeng has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Taijun Jiang
Hunan Engineering Research Center of Research and Development of Degradable Materials and Molding Technology, Changsha University Changsha China
5 shared publicationsCan Hu
Hunan Engineering Research Center of Research and Development of Degradable Materials and Molding Technology, Changsha University Changsha China
3 shared publications- Can Hu
Materials Science and Engineering Hunan Institute of Technology Hengyang Hunan China
3 shared publications Cong Meng
Hunan Key Laboratory of Biomass Fiber Functional Materials, Hunan International Scientific and Technological Innovation Cooperation Base of Biomass Fiber Materials and Application, National and Local Joint Engineering Research Center of Advanced Packaging Materials Research and Development Technology, School of Urban and Environmental, Hunan University of Technology, Zhuzhou, China
2 shared publications- Taijun Jiang
Hunan University of Technology
2 shared publications - Chang Peng
College of Chemistry and Chemical Engineering
1 shared publication
Latest Publications
- 5 March 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (5) , 3466-3476
Radical‐Regulated Synthesis of Long‐Chain Branched Polylactic Acid Toward Enhanced Melt Strength
In this work, long‐chain branched polylactic acid (LCB‐PLA) with enhanced melt strength was synthesized via a radical‐regulated strategy using diisopropylphenyl peroxide (DCP) as the radical initiator, polyfunctional pentaerythritol tetraacrylate (PET4A) as the branching agent, and tetramethyltoluene disulfide (TMTD) as the radical regulators. Meanwhile, the synthesized mechanism of the functional PLA was investigated. Experimental results demonstrated that TMTD effectively promoted the branching efficiency of PET4A monomers and facilitated the formation of long branched chains along the PLA backbone. Moreover, the terminal slope of the storage modulus for the modified PLA decreased from 1.76 to 0.74. Additionally, deviations observed in the Cole–Cole plot indicated slower molecular chain relaxation after long‐chain branching, along with prolonged relaxation time. Notably, the crystallinity, crystallization rate, and crystallization temperature of the modified PLA all improved with increasing branching degree, with the half‐crystallization time reduced to 0.47 min. Thus, the modified PLA synthesized via this radical‐regulated strategy exhibited significantly enhanced melt strength and improved crystallization behavior, which may broaden its applicability in processing‐related applications.
- 5 March 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (5) , 3466-3476
Radical‐Regulated Synthesis of Long‐Chain Branched Polylactic Acid Toward Enhanced Melt Strength
In this work, long‐chain branched polylactic acid (LCB‐PLA) with enhanced melt strength was synthesized via a radical‐regulated strategy using diisopropylphenyl peroxide (DCP) as the radical initiator, polyfunctional pentaerythritol tetraacrylate (PET4A) as the branching agent, and tetramethyltoluene disulfide (TMTD) as the radical regulators. Meanwhile, the synthesized mechanism of the functional PLA was investigated. Experimental results demonstrated that TMTD effectively promoted the branching efficiency of PET4A monomers and facilitated the formation of long branched chains along the PLA backbone. Moreover, the terminal slope of the storage modulus for the modified PLA decreased from 1.76 to 0.74. Additionally, deviations observed in the Cole–Cole plot indicated slower molecular chain relaxation after long‐chain branching, along with prolonged relaxation time. Notably, the crystallinity, crystallization rate, and crystallization temperature of the modified PLA all improved with increasing branching degree, with the half‐crystallization time reduced to 0.47 min. Thus, the modified PLA synthesized via this radical‐regulated strategy exhibited significantly enhanced melt strength and improved crystallization behavior, which may broaden its applicability in processing‐related applications.
- 15 April 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (7) , 3003-3010
Shear relaxation behavior for degraded polypropylene melt in torque rheometer
Shear relaxation behavior for polymer melt exists in different processing techniques and influences the dimensional accuracy and production efficiency of polymer products. A micro physical and mathematical model based on microstructure of polymer chains and processing parameters was established and verified by experimental results obtained from a torque rheometer. The shear relaxation time of polypropylene degraded by di‐tert‐butyl peroxide was characterized with torque rheometer. The effects of microstructure and processing parameters on the shear relaxation time was investigated. The results showed that a wider molecular weight distribution could result in a decrease in shear relaxation time and polypropylene chains with higher molecular weight were more sensitive to molecular weight distribution. The shear relaxation time declined exponentially with shear rate and increased with internal pressure. The temperature could enhance the movement of polymer chains and reduce the shear relaxation time linearly, but polypropylene with lower molecular weight was less sensitive to temperature. The insight obtained from the mathematical and experimental results can be profoundly applied in practical process control to manufacture product with better dimensional stability and production efficiency for viscoelastic polymer.Highlights: A physical and mathematical model based on microstructure and processing parameters of molecular chains was established to explore the shear relaxation mechanism. Shear relaxation time of polypropylene degraded by di‐tert‐butyl peroxide was characterized with the help of torque rheometer. The effects of microstructure and processing parameters on shear relaxation time was investigated to optimize the manufacturing of polypropylene products.
- 15 April 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (7) , 3003-3010
Shear relaxation behavior for degraded polypropylene melt in torque rheometer
Shear relaxation behavior for polymer melt exists in different processing techniques and influences the dimensional accuracy and production efficiency of polymer products. A micro physical and mathematical model based on microstructure of polymer chains and processing parameters was established and verified by experimental results obtained from a torque rheometer. The shear relaxation time of polypropylene degraded by di‐tert‐butyl peroxide was characterized with torque rheometer. The effects of microstructure and processing parameters on the shear relaxation time was investigated. The results showed that a wider molecular weight distribution could result in a decrease in shear relaxation time and polypropylene chains with higher molecular weight were more sensitive to molecular weight distribution. The shear relaxation time declined exponentially with shear rate and increased with internal pressure. The temperature could enhance the movement of polymer chains and reduce the shear relaxation time linearly, but polypropylene with lower molecular weight was less sensitive to temperature. The insight obtained from the mathematical and experimental results can be profoundly applied in practical process control to manufacture product with better dimensional stability and production efficiency for viscoelastic polymer.Highlights: A physical and mathematical model based on microstructure and processing parameters of molecular chains was established to explore the shear relaxation mechanism. Shear relaxation time of polypropylene degraded by di‐tert‐butyl peroxide was characterized with the help of torque rheometer. The effects of microstructure and processing parameters on shear relaxation time was investigated to optimize the manufacturing of polypropylene products.
- 19 July 2022
- Published by Springer Nature in Macromolecular Research
- Vol. 30 (11) , 826-835
Structure and Properties of Low Dielectric Constant Polyetherimide Films Containing-CF3 and Cardo Groups
- 19 July 2022
- Published by Springer Nature in Macromolecular Research
- Vol. 30 (11) , 826-835
Structure and Properties of Low Dielectric Constant Polyetherimide Films Containing-CF3 and Cardo Groups
- 30 May 2022
- Published by Pleiades Publishing Ltd in Polymer Science, Series B
- Vol. 64 (4) , 518-525
Effect of Processing Temperature on the Thermal and Mechanical Properties of BPDA–PDA
High heat resistant and stable dimensional PI films have been widely used in organic light emitting diode industry, therefore the comprehensive performance should be enhanced. The PI films of low CTE and high heat resistance were prepared with 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) and p-phenylenediamine (PDA) under different processing conditions. WAXD and FTIR were performed to characterize the microstructure of the films. DMA and TMA were conducted to investigate the mechanical and thermal properties of the films. The results showed that the density of the films increased and water absorption rate decreased with fabrication temperature as a result of the smectic structure. The smectic structure of the film attributed to the oriented polymer chains was observed in the DMA curves peaked at 470°C. The film would shrink at round the glass transition temperature as indicated by the TMA curves when it was prepared at relatively lower fabrication temperature, resulting in a larger CTE value compared with other prepared at high fabrication temperature. The 1% weight loss temperature increased with the fabrication temperature for the smectic structure. The tensile strength and elongation at break of the film increased with smectic density. The heat resistance and mechanical performance of bioriented films were the best among all the samples as the PI chains were stretched during the imidization process when all the edges of the film were fixed. The results obtained in this paper could offer practical and valuable references to optimization of processing parameters for the preparation of high performance PI films.
- 30 May 2022
- Published by Pleiades Publishing Ltd in Polymer Science, Series B
- Vol. 64 (4) , 518-525
Effect of Processing Temperature on the Thermal and Mechanical Properties of BPDA–PDA
High heat resistant and stable dimensional PI films have been widely used in organic light emitting diode industry, therefore the comprehensive performance should be enhanced. The PI films of low CTE and high heat resistance were prepared with 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) and p-phenylenediamine (PDA) under different processing conditions. WAXD and FTIR were performed to characterize the microstructure of the films. DMA and TMA were conducted to investigate the mechanical and thermal properties of the films. The results showed that the density of the films increased and water absorption rate decreased with fabrication temperature as a result of the smectic structure. The smectic structure of the film attributed to the oriented polymer chains was observed in the DMA curves peaked at 470°C. The film would shrink at round the glass transition temperature as indicated by the TMA curves when it was prepared at relatively lower fabrication temperature, resulting in a larger CTE value compared with other prepared at high fabrication temperature. The 1% weight loss temperature increased with the fabrication temperature for the smectic structure. The tensile strength and elongation at break of the film increased with smectic density. The heat resistance and mechanical performance of bioriented films were the best among all the samples as the PI chains were stretched during the imidization process when all the edges of the film were fixed. The results obtained in this paper could offer practical and valuable references to optimization of processing parameters for the preparation of high performance PI films.
- 17 February 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (5) , 2584-2592
Effect of compression parameters on stress relaxation behavior of bamboo fiber reinforced polypropylene composites
A self‐made thermal mechanical analyzer was manufactured to characterized the compression and bending stress relaxation behavior for bamboo fiber reinforced polypropylene composite with different bamboo fiber and coupling agent concentration. The effects of bamboo fiber concentration, interfacial strength, load controlling method, compression speed, and temperature on composite stress relaxation parameters were investigated. The obtained results show that two‐stage relaxation process could be observed for both compression and bending test while shearing relaxation process was a single exponential decay. The relaxation time for slow exponential relaxation process was two orders of magnitude to that for fast relaxation process and the force decay amplitude on the first linear stage was about 3.5 times as much as that on the second exponential decay stage. Both the filling of bamboo fiber and coupling agent could increase the stress relaxation time but higher temperature would promote the movement of polymer chains and lengthen the stress relaxation time. The insights obtained from the experiments and fitting results can offer valuable reference to precisely controlling of dimensional accuracy and production efficiency for the composite products of irregular structure.
- 17 February 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (5) , 2584-2592
Effect of compression parameters on stress relaxation behavior of bamboo fiber reinforced polypropylene composites
A self‐made thermal mechanical analyzer was manufactured to characterized the compression and bending stress relaxation behavior for bamboo fiber reinforced polypropylene composite with different bamboo fiber and coupling agent concentration. The effects of bamboo fiber concentration, interfacial strength, load controlling method, compression speed, and temperature on composite stress relaxation parameters were investigated. The obtained results show that two‐stage relaxation process could be observed for both compression and bending test while shearing relaxation process was a single exponential decay. The relaxation time for slow exponential relaxation process was two orders of magnitude to that for fast relaxation process and the force decay amplitude on the first linear stage was about 3.5 times as much as that on the second exponential decay stage. Both the filling of bamboo fiber and coupling agent could increase the stress relaxation time but higher temperature would promote the movement of polymer chains and lengthen the stress relaxation time. The insights obtained from the experiments and fitting results can offer valuable reference to precisely controlling of dimensional accuracy and production efficiency for the composite products of irregular structure.
- 20 May 2021
- Published by Springer Nature in Fibers and Polymers
- Vol. 22 (8) , 2187-2193
Morphological, Thermal, Mechanical, and Optical Properties of Hybrid Nanocellulose Film Containing Cellulose Nanofiber and Cellulose Nanocrystals
- 20 May 2021
- Published by Springer Nature in Fibers and Polymers
- Vol. 22 (8) , 2187-2193
Morphological, Thermal, Mechanical, and Optical Properties of Hybrid Nanocellulose Film Containing Cellulose Nanofiber and Cellulose Nanocrystals
- 3 March 2021
- Published by Springer Nature in Fibers and Polymers
- Vol. 22 (4) , 957-963
Optimization of Processing Parameters for Particle Filtration Efficiency of Polypropylene Melt-blown Fabric
Polypropylene melt-blown fabric as the core filter materials plays an important role in manufacturing civil and medical epidemic prevention products. The aim of this study was to optimize and control the particle filtration efficiency and apparent surface quality of the melt-blown fabric from the perspectives of electret masterbatch composition and processing parameters. Magnesium stearate and fumed silica were used as the electret to manufacture polypropylene melt-blown fabric. The layout and charge voltage of the electret device was taken as the variables to optimize and improve the particle filtration efficiency and bulkiness coefficient of the fabric. The temperature of the barrel and die was controlled to enhance the surface quality and corresponding particle filtration efficiency. The results showed that a combination of organic magnesium stearate and inorganic fumed silica could obtain a balance between particle filtration efficiency and smooth processing without being jammed. Increasing the charge voltage and rearranging the position of the charge wires could significantly enhance the particle filtration efficiency. A better particle filtration efficiency and reasonable bulkiness coefficient could be obtained by controlling the diameter of the filaments by regulating the temperature of the barrel and die as well as the suction intensity. The results obtained from this study can offer valuable references in optimization of electret master batch formulation and processing parameters for melt-blown fabric production with different resin.
- 3 March 2021
- Published by Springer Nature in Fibers and Polymers
- Vol. 22 (4) , 957-963
Optimization of Processing Parameters for Particle Filtration Efficiency of Polypropylene Melt-blown Fabric
Polypropylene melt-blown fabric as the core filter materials plays an important role in manufacturing civil and medical epidemic prevention products. The aim of this study was to optimize and control the particle filtration efficiency and apparent surface quality of the melt-blown fabric from the perspectives of electret masterbatch composition and processing parameters. Magnesium stearate and fumed silica were used as the electret to manufacture polypropylene melt-blown fabric. The layout and charge voltage of the electret device was taken as the variables to optimize and improve the particle filtration efficiency and bulkiness coefficient of the fabric. The temperature of the barrel and die was controlled to enhance the surface quality and corresponding particle filtration efficiency. The results showed that a combination of organic magnesium stearate and inorganic fumed silica could obtain a balance between particle filtration efficiency and smooth processing without being jammed. Increasing the charge voltage and rearranging the position of the charge wires could significantly enhance the particle filtration efficiency. A better particle filtration efficiency and reasonable bulkiness coefficient could be obtained by controlling the diameter of the filaments by regulating the temperature of the barrel and die as well as the suction intensity. The results obtained from this study can offer valuable references in optimization of electret master batch formulation and processing parameters for melt-blown fabric production with different resin.
- 14 March 2020
- Published by Wiley in Polymer Composites
- Vol. 41 (7) , 2724-2731
Fabrication of highly filled wood plastic composite pallets with extrusion‐compression molding technique
The aim of this study was to fabricate highly filled wood plastic composite pallets with extrusion‐compression molding technique and investigate the effects of processing parameters on mechanical performance and production stability. The composites were blended in twin‐screw extruder and subsequently measured by weight with an electronic scale. Before compression, it was divided into pieces and rearranged in the cavities of compression mould according to the mass distribution. The effects of compression pressure and mould temperature on flexure strength, density, water absorption, and dimensional deviation were investigated. The results show that both the flexure strength and density of the pallets increased with compression pressure and remained higher than that of extruded deck when compression pressure exceeded 6.5 MPa. Water absorption and dimensional deviation decreased with compression pressure and remained lower than that of extruded deck after the compression pressure exceeded 6.0 MPa. Compression pressure could increase the final passed yield by improving the composite melt filling state and lowering the buckling deformation, but further increase above 6.7 MPa would result in a decline in final passed yield. Increase in mould temperature contributed to the production stability but an excessive value would extend the molding cycle. The insights gained from this study may be of assistance in optimizing extrusion‐compression processing parameters and expanding the application of highly filled wood plastic composites in complicated and irregular products.
- 14 March 2020
- Published by Wiley in Polymer Composites
- Vol. 41 (7) , 2724-2731
Fabrication of highly filled wood plastic composite pallets with extrusion‐compression molding technique
The aim of this study was to fabricate highly filled wood plastic composite pallets with extrusion‐compression molding technique and investigate the effects of processing parameters on mechanical performance and production stability. The composites were blended in twin‐screw extruder and subsequently measured by weight with an electronic scale. Before compression, it was divided into pieces and rearranged in the cavities of compression mould according to the mass distribution. The effects of compression pressure and mould temperature on flexure strength, density, water absorption, and dimensional deviation were investigated. The results show that both the flexure strength and density of the pallets increased with compression pressure and remained higher than that of extruded deck when compression pressure exceeded 6.5 MPa. Water absorption and dimensional deviation decreased with compression pressure and remained lower than that of extruded deck after the compression pressure exceeded 6.0 MPa. Compression pressure could increase the final passed yield by improving the composite melt filling state and lowering the buckling deformation, but further increase above 6.7 MPa would result in a decline in final passed yield. Increase in mould temperature contributed to the production stability but an excessive value would extend the molding cycle. The insights gained from this study may be of assistance in optimizing extrusion‐compression processing parameters and expanding the application of highly filled wood plastic composites in complicated and irregular products.
- 1 April 2019
- Published by Springer Nature in Fibers and Polymers
- Vol. 20 (4) , 804-810
An Online Extrusion-compression Molding Method to Produce Wood Plastic Composite Packaging Boxes
- 1 April 2019
- Published by Springer Nature in Fibers and Polymers
- Vol. 20 (4) , 804-810
An Online Extrusion-compression Molding Method to Produce Wood Plastic Composite Packaging Boxes
- 23 April 2013
- Published by Springer Nature in Journal of Materials Research
- Vol. 28 (10) , 1394-1404
Synthesis and characterization of pH and temperature double-sensitive nanocomposite hydrogels consisting of poly(dimethylaminoethyl methacrylate) and clay
- 23 April 2013
- Published by Springer Nature in Journal of Materials Research
- Vol. 28 (10) , 1394-1404
Synthesis and characterization of pH and temperature double-sensitive nanocomposite hydrogels consisting of poly(dimethylaminoethyl methacrylate) and clay