PTPatrick Thompson

Patrick Thompson

*This is an algorithmically generated author record based on publicly available information.

Patrick Thompson has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The History of Fluid Resuscitation for Bleeding

    by Patrick Thompson, Geir Strandenes

    Damage control resuscitation (DCR) is a bundle of care first described by Holcomb et al. that is aimed at reducing death from hemorrhage for patients with severe traumatic bleeding. DCR principles include compressible hemorrhage control; hypotensive resuscitation; rapid surgical control of bleeding; avoidance of the overuse of crystalloids and colloids, prevention or correction of acidosis, hypothermia, and hypocalcaemia; and hemostatic resuscitation (blood-based resuscitation). Remote damage control resuscitation (RDCR) is defined as the prehospital application of DCR concepts. The term RDCR was first published by Gerhardt and has been disseminated by the (Trauma Hemostasis and Oxygenation Research), or THOR Network. The history of DCR and RDCR starts well before the inception of the terms. The concepts behind the principles of DCR and RDCR stretch far back into the past. This chapter provides an outline of this history, but it is limited to the fluid resuscitation aspect of DCR/RDCR.


  • Diffusion Creep of Realistic SnAgCu Solder Joints at Times and Stresses of Relevance to Thermal Fatigue

    by T. Alghoul, L. Wentlent, R. Sivasubramony, C. Greene, P. Thompson, P. Borgesen

    A minimum requirement of constitutive relations for the modeling of the behavior of realistic SnAgCu is that they predict creep rates under constant stresses in the range of interest. Preliminary results have however shown common constitutive relations to not do so even at the relatively high stresses of relevance to life in accelerated thermal cycling or vibration. Focusing on times of relevance to thermal fatigue, as opposed to the much longer times required to reach steady state, this is shown to be a result of the inelastic deformation of realistic Sn3.0Ag0.5Cu solder joints being dominated by diffusion, rather than by the motion of dislocations as commonly assumed.


  • Effects of Thermal Cycling on Creep of SnAgCu Solder Joints

    by T. Alghoul, L. Wentlent, R. Sivasubramony, C. Greene, P. Thompson, P. Borgesen

    The long-term life of properly optimized high-end microelectronics assemblies is commonly limited by fatigue of the solder joints. The most credible assessments of this rely on modeling-based extrapolation and generalization of accelerated test results. As the validity of extrapolations to long-term service can rarely if ever be verified experimentally, there is a strong need for mechanistically justified models. The models all rely on predictions of stresses, strains, and perhaps functions of those versus time and temperature in cycling. Finite-element-based predictions of these require the assumption of relatively complex constitutive relations capable of predicting inelastic strain rates under continuously varying stresses and temperatures. These are usually extracted from a series of creep or stress relaxation experiments and generalized under the implicit assumption that the inelastic deformation is dominated by dislocation creep. However, the resulting constitutive relations were recently shown to be strongly misleading. It was suggested that this is a result of the inelastic deformation at the stresses and temperatures of primary concern actually being dominated by dislocation core diffusion. This paper lends further support for this picture, showing additional contributions from diffusion on cycling induced dislocation structures to make for ongoing, usually nonmonotonic, variations in deformation rates from cycle to cycle. These effects are certain to have major consequences for modeling. In fact, it has been argued that the combination of wrong constitutive relations with a wrong damage function has led to a partial cancellation of errors across a limited parameter range, but that this cannot be counted on for more detailed predictions of accelerated test results and does not allow for interpretation of such results in terms of even qualitative trends in service.


  • Open Access

    A proposed field emergency donor panel questionnaire and triage tool

    by Heidi Doughty, Patrick Thompson, Andrew P. Cap, Philip C. Spinella, Elon Glassberg, Håkon Skogrand Eliassen, Marc De Pasquale, Geir Strandenes

    The provision of transfusion support to isolated military or civilian projects may require the use of an emergency donor panel (EDP) for immediate warm fresh whole blood (WFWB). The aim of this short discussion article is to raise and resolve some of the practical aspects for the nonspecialist faced with the emergency collection of WFWB whole blood in the austere medical environment (AME). A proposed field EDP questionnaire and triage tool (QTT) is presented. It is designed for the hostile, remote, or austere environment that falls outside normal regulated supply of cold-stored blood products or removed from trained blood collection personnel, where collection may fall to an isolated medical provider. The tool has been drafted based on review of existing guidelines and consultation with practitioners. It serves as a point of reference for local guidelines and has yet to be validated. The use of the EDP is associated with risk; however, it remains the simplest method of providing rapid transfusion support. The best way to manage the risk is to brief and prescreen blood donors before deployment. An abbreviated donor QTT can be an aide to decision making at the time of donation. The tool should be tailored to requirements and underpinned by policy and training.