AVArturo Villiger

Arturo Villiger

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Arturo Villiger has a total of 52 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    IGS BDS-3 satellite antenna calibration campaign

    by Peter Steigenberger, Paul Rebischung, Kyohei Akiyama, Elmar Brockmann, Zhiguo Deng, Florian Dilssner, Bingbing Duan, Bingchen Fu, Jianghui Geng, Jing Guo, et al.

    A new antenna model for BeiDou-3 satellites in medium Earth orbit (MEO) and inclined geosynchronous orbit (IGSO) is presented. This model enables consistent processing of BeiDou-3 with other GNSSs in the IGS20 reference frame and has been adopted for use within the International GNSS Service (IGS) in February 2026. The model introduces estimated phase patterns for four different blocks of BeiDou-3 satellites and provides satellite- and frequency-specific phase center offsets (PCOs) for the B1, B2, and B3 bands. B1C/B2a phase patterns and PCOs are obtained as weighted averages of individual estimates from up to nine IGS analysis centers (ACs) to minimize the dependence on AC-specific models and processing standards. In order to support users of the B1I/B3I legacy signals, satellite-specific PCOs for this linear combination have been determined by two ACs. As part of the antenna model development, temporal variations of PCOs at the few decimeter level were observed over the 2021–2024 time frame for selected satellites built by the Shanghai Engineering Center for Microsatellites (SECM), which are handled as piece-wise constant PCOs in the new IGS antenna model for the affected satellites. The new phase center model is aligned to the IGS20 reference frame and ensures consistency between GPS, GLONASS, Galileo, and BeiDou-3 in multi-GNSS processing. A precise point positioning validation of the new antenna model with B1C/B2a observations confirms a 0.11 ppb scale consistency of BeiDou-3 with the IGS20 reference frame.

  • Open Access

    Multi-facility GNSS antenna calibration

    by Tobias Kersten, Johannes Kröger, Steffen Schön, Andria Bilich, Igor Sutyagin, Martin Schmitz, Ansgar Dreier, Heiner Kuhlmann, Stefano Caizzone, Benedikt Soja, et al.

    Accurate antenna calibrations are a cornerstone of high-quality global navigation satellite systems (GNSS) positioning, time and frequency transfer, precise orbits, and troposphere estimates. The international GNSS service (IGS) antenna committee maintains antenna phase center corrections in the ANTEX file relying on five calibration facilities. Since new calibration facilities have been set up and user demands have grown along with hardware and software updates of GNSS, we organized an international inter-comparison across nine facilities, using both anechoic chambers and field robots. Six antennas with different designs were calibrated by each facility and compared with the Geo++ robot solution (GPP4), a proxy for the IGS ANTEX. Where available, we also considered the IGS type means. We examined differences between the antenna patterns and subsequent differences in station coordinates. To this end, we used a standardized forward simulation as well as multi-GNSS PPP solutions using the GNSS toolbox developed at Leibniz University Hannover, Institut für Erdmessung (IfE). Our study yields several important results. We found that multi-GNSS antenna calibrations exhibit frequency- and elevation-dependent variations, with deviations of up to 3 mm to 4 mm at low elevations. We show that organizations like Topcon (TPS), national geodetic survey (NGS), and Wuhan GNSS Research Center (WHU) yield calibration results that are in very good agreement with those of IGS accepted facilities such as GPP, IfE, and to some extent geoscience Australia (GA). These differences result in position deviations of a few millimeters, with the Up component being the dominant contributor.

  • Open Access

    Flatness constraints in the estimation of GNSS satellite antenna phase center offsets and variations

    by Bingbing Duan, Urs Hugentobler, Oliver Montenbruck, Peter Steigenberger, Arturo Villiger

    Accurate information on satellite antenna phase center offsets (PCOs) and phase variations (PVs) is indispensable for high-precision geodetic applications. In the absence of consistent pre-flight calibrations, satellite antenna PCOs and PVs of global navigation satellite systems are commonly estimated based on observations from a global network, constraining the scale to a given reference frame. As part of this estimation, flatness and zero-mean conditions need to be applied to unambiguously separate PCOs, PVs, and constant phase ambiguities. Within this study, we analytically investigate the impact of different boresight-angle-dependent weighting functions for PV minimization, and we compare antenna models generated with different observation-based weighting schemes with those based on uniform weighting. For the case of the GPS IIR/-M and III satellites, systematic differences of 10 mm in the PVs and 65 cm in the corresponding PCOs are identified. In addition, new antenna models for the different blocks of BeiDou-3 satellites in medium Earth orbit are derived using different processing schemes. As a drawback of traditional approaches estimating PCOs and PVs consecutively in distinct steps, it is shown that different, albeit self-consistent, PCO/PV pairs may result depending on whether PCOs or PVs are estimated first. This apparent discrepancy can be attributed to potentially inconsistent weighting functions in the individual processing steps. Use of a single-step process is therefore proposed, in which a dedicated constraint for PCO-PV separation is applied in the solution of the normal equations. Finally, the impact of neglecting phase patterns in precise point positioning applications is investigated. In addition to an overall increase of the position scatter, the occurrence of systematic height biases is illustrated. While observation-based weighting in the pattern estimation can help to avoid such biases, the possible benefit depends critically on the specific elevation-dependent weighting applied in the user’s positioning model. As such, the practical advantage of such antenna models would remain limited, and uniform weighting is recommended as a lean and transparent approach for the pattern estimation of satellite antenna models from observations.


  • Open Access

    Between-satellite ambiguity resolution based on preliminary GNSS orbit and clock information using a globally applied ambiguity clustering strategy

    by Emilio J. Calero-Rodríguez, Arturo Villiger, Stefan Schaer, Rolf Dach, Adrian Jäggi

    The use of undifferenced (UD) processing schemes of GNSS measurements is becoming more and more popular for the generation of global network solutions (GNSS orbits and clock products) within the GNSS community. As opposed to classical processing schemes, which are based on a two-step approach where the orbits (generally, the contributions to the observation geometry) are estimated in a double-difference (DD) scheme while leaving the estimation of the corresponding clock information (and other linear terms) to a second, independent UD procedure where the orbits are introduced as known, the newer designs combine both parts into a single, compact processing scheme. Although this offers a higher flexibility, some challenges arise from the handling of the many parameters, as well as from the implementation of robust ambiguity resolution (AR) strategies. The latter could lead to a prohibitive computational time for a growing size of the network due to the large amount of ambiguity parameters. To overcome that issue, we propose a new UD-AR strategy that adapts the DD-AR approach. This is accomplished by carefully inspecting the real-valued ambiguities in a stand-alone step, where the DD-AR information is explicitly considered through the use of ambiguity clusters. As a result, the preliminary satellite orbits and clock corrections are modified to become consistent with the integer-cycle property of the carrier phase ambiguities, allowing to resolve them as integer numbers in a computationally inexpensive station-wise parallelization. This strategy is introduced and explained in detail. Moreover, it is shown that the GPS and Galileo solutions generated by this procedure are at a competitive level compared to classical DD-based solutions.


  • Open Access

    On the relation of GNSS phase center offsets and the terrestrial reference frame scale: a semi-analytical analysis

    by Oliver Montenbruck, Peter Steigenberger, Arturo Villiger, Paul Rebischung

    Phase center offsets (PCOs) of global navigation satellites systems (GNSS) transmit antennas along the boresight axis introduce line-of-sight-dependent range changes in the modeling of GNSS observations that are strongly correlated with the estimated station heights. As a consequence, changes in the adopted PCOs impact the scale of GNSS-based realizations of the terrestrial reference frame (TRF). Vice versa, changes in the adopted TRF scale require corrections to the GNSS transmit antenna PCOs for consistent observation modeling. Early studies have determined an approximate value of $$\alpha =-0.050$$ α = - 0.050 for the ratio of station height changes and satellite PCO changes in GPS orbit determination and phase center adjustment. However, this is mainly an empirical value and limited information is available on the actual PCO-scale relation and how it is influenced by other factors. In view of the recurring need to adjust the IGS antenna models to new ITRF scales, a semi-analytical model is developed to determine values of $$\alpha $$ α for the four current GNSSs from first principles without a need for actual network data processing. Given the close coupling of satellite boresight angle and station zenith angle, satellite PCO changes are essentially compensated by a combination of station height, zenith troposphere delay, and receiver clock offset. As such, the value of $$\alpha $$ α depends not only on the orbital altitude of the considered GNSS but also on the elevation-dependent distribution of GNSS observations and their weighting, as well as the elevation mask angle and the tropospheric mapping function. Based on the model, representative values of $$\alpha _\text {GPS}=-0.051$$ α GPS = - 0.051 , $$\alpha _\text {GLO}=-0.055$$ α GLO = - 0.055 , $$\alpha _\text {GAL}=-0.041$$ α GAL = - 0.041 , and $$\alpha _\text {BDS-3}=-0.046$$ α BDS-3 = - 0.046 are derived for GPS, GLONASS, Galileo, and BeiDou-3 at a $$10^\circ $$ 10 ∘ elevation cutoff angle. These values may vary by $$\varDelta \alpha \approx 0.003$$ Δ α ≈ 0.003 depending on the specific model assumptions and data processing parameters in a precise orbit determination or precise point positioning. Likewise changes of about $$\pm 0.003$$ ± 0.003 can be observed when varying the cutoff angle between $$5^\circ $$ 5 ∘ and $$15^\circ $$ 15 ∘ .


  • Open Access

    Combined orbit and clock zero-difference solution at CODE: ambiguity resolution strategy

    by Emilio José Calero Rodríguez, Arturo Villiger, Stefan Schaer, Rolf Dach, Adrian Jäggi

    The use of zero-difference processing schemes becomes more and more popular within the GNSS (Global Navigation Satellite Systems) community. This change from double- to zero-difference approaches increases the demand of PPP-AR (Ambiguity Resolution for Precise Point Positioning) enabling products. Those products can be created in two ways, either estimate the geometrical part (orbits) based on a double-difference global network solution with a separate zero-difference solution for the clocks and phase biases, or in a combined zero-difference solution. The latter one allows a more flexible approach; however, the challenge lies in the handling of the increased number of parameters and ambiguity resolution.The estimation of combined orbit and clock zero-difference enabling products needs a thought-out design of the processing strategy, where the elimination and back-substitution steps are vital to deal with the large number of parameters. Nonetheless, the amount of ambiguity parameters dramatically grows with an increasing size of the network, posing some computational limitations, since they should not be eliminated for a successful ambiguity resolution. Such a restriction originates from fixing float orbits: their accuracy does not allow to estimate reliable ambiguity parameters. To cope with that, we propose a new algorithm capable to decouple them from the orbits, allowing to fix between-satellite ambiguities in a later station-wise parallelisation.On the poster, we describe selected details on the ambiguity resolution strategy that we have developed. The obtained results are characterized and compared to other solutions using classical ambiguity resolution schemes.

  • Open Access

    Compatibility between the preliminary ITRF2020 solution and GNSS antenna phase center offsets

    by Arturo Villiger, Rolf Dach, Lars Prange, Daniel Arnold, Maciek Kalarus, Stefan Schaer, Pascal Stebler, Adrian Jäggi

    The release of the next International Terrestrial Reference Frame (ITRF) 2020 is based on the four geodetic techniques, namely Satellite Laser Ranging (SLR), Very Long Baseline Interferometry (VLBI), Global Navigation Satellite Systems (GNSS), and Doppler Orbitography and Radio-positioning Integrated by Satellite instrument (DORIS). The upcoming release will presumably define the scale based on the first two techniques.The GNSS scale is mainly driven by the z-component of the satellite antenna phase center offsets. With the disclosure of the Galileo metadata by the European GNSS Agency (GSA) the satellite antenna pattern became available to the public and enabled the GNSS scale determination.We aim to analyze the consistency between the preliminary ITRF 2020 solution and the GNSS based scale. In addition, we will extend our study with all available TRF solutions and compare their consistency with the GNSS derived scale and discuss the resulting comparisons. 


  • Open Access

    Extension of the repro3 ANTEX file with BeiDou and QZSS satellite antenna pattern

    by Arturo Villiger, Rolf Dach, Lars Prange, Adrian Jäggi

    During the preparations for the International GNSS Service (IGS) contribution to the next reference frame, called repro3, the disclosed pre-launch chamber calibrated Galileo satellite antenna pattern were analyzed. Those tests revealed a discrepancy between the GPS and GLONASS z-component of the phase center offsets (PCO), aligned to the IGS14 scale, and the calibrated Galileo z-PCOs. In order to make the PCOs compatible to the repro3 it was decided to rely on the calibrated Galileo pattern and adjust the GPS and GLONASS PCOs accordingly. Combined with multi-GNSS receiver calibrations for all systems the repro3 might contribute to the scale determination for the next reference frame.As the repro3 is based on GPS, GLONASS, and Galileo only those three systems have been analyzed leading to the repro3 ANTEX file, containing all used antenna pattern, which is aligned to the Galileo induced scale. In order to extend the repro3 ANTEX file with satellite calibrations for BeiDou and QZSS a dedicated reprocessing based on CODEs MGEX solution is made to assess the available PCOs for those satellites and tests their consistency with the repro3 scale. The results should allow to extend the repro3 ANTEX with the BDS and QZSS pattern for experimental purposes.


  • Open Access

    GNSS scale determination using calibrated receiver and Galileo satellite antenna patterns

    by Arturo Villiger, Rolf Dach, Stefan Schaer, Lars Prange, Florian Zimmermann, Heiner Kuhlmann, Gerhard Wübbena, Martin Schmitz, Gerhard Beutler, Adrian Jäggi

    The reference frame of a global terrestrial network is defined by the origin, the orientation and the scale. The origin of the ITRF2014 is defined by the ILRS long-term solution, the orientation by no-net rotation conditions w.r.t. the previous reference frame (ITRF2008), and the scale by the mean values from global VLBI and SLR solution series (Altamimi et al. in J Geophys Res Solid Earth 121:6109–6131, 2016). With the release of the Galileo satellite antenna phase center offsets (PCO) w.r.t. the satellites center of mass (GSA in Galileo IOV and FOC satellite metadata, 2019) and the availability of new ground antenna calibrations for GNSS receivers, based on anechoic chamber measurements or on robot calibrations, GNSS global network solutions qualify to contribute to the scale determination of terrestrial networks, as well. Our analysis is based on global multi-GNSS solutions of the years 2017 and 2018 and may be seen as “proof of concept” for the contribution of GNSS data to the scale determination of the terrestrial reference frame. In a first step, the currently used Galileo PCO estimations (Steigenberger et al. in J Geod 90:773–785, 2016) are compared to the released PCO values, which show discrepancies on the decimeter-level. Eventually, the published Galileo PCOs are used in an experimental solution as known values. GNSS-specific PCOs are estimated, as well, for GPS and GLONASS, together with the “standard” parameters set up in global GNSS solutions. From the estimated network coordinates, a time series of daily scale parameters of the terrestrial network is extracted, which shows an offset of the order of 1 ppb (parts per billion, corresponding to a height difference of 6.4 mm on the Earth’s surface) w.r.t. to the ITRF2014 network and an annual variation with an amplitude of about 0.3 ppb.


  • Open Access

    Validation of the EGSIEM-REPRO GNSS Orbits and Satellite Clock Corrections

    by Andreja Sušnik, Andrea Grahsl, Daniel Arnold, Arturo Villiger, Rolf Dach, Gerhard Beutler, Adrian Jäggi

    In the framework of the European Gravity Service for Improved Emergency Management (EGSIEM) project, consistent sets of state-of-the-art reprocessed Global Navigation Satellite System (GNSS) orbits and satellite clock corrections have been generated. The reprocessing campaign includes data starting in 1994 and follows the Center for Orbit Determination in Europe (CODE) processing strategy, in particular exploiting the extended version of the empirical CODE Orbit Model (ECOM). Satellite orbits are provided for Global Positioning System (GPS) satellites since 1994 and for Globalnaya Navigatsionnaya Sputnikovaya Sistema (GLONASS) since 2002. In addition, a consistent set of GPS satellite clock corrections with 30 s sampling has been generated from 2000 and with 5 s sampling from 2003 onwards. For the first time in a reprocessing scheme, GLONASS satellite clock corrections with 30 s sampling from 2008 and 5 s from 2010 onwards were also generated. The benefit with respect to earlier reprocessing series is demonstrated in terms of polar motion coordinates. GNSS satellite clock corrections are validated in terms of completeness, Allan deviation, and precise point positioning (PPP) using terrestrial stations. In addition, the products herein were validated with Gravity Recovery and Climate Experiment (GRACE) precise orbit determination (POD) and Satellite Laser Ranging (SLR). The dataset is publicly available.