Hyunsu Kim
Research Subjects
Hyunsu Kim has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Trevor D. Hrynyk
University of Waterloo
6 shared publications Oguzhan Bayrak
Univ. of Texas at Austin
5 shared publications- Yousun Yi
Univ. of Texas at Austin
4 shared publications Alex Katz
Restoration Engineer II, Walker Parking Consultants, 850 West Jackson Blvd., Chicago, IL 60607
2 shared publicationsJessica Salazar
Bridge EIT, HDR, Inc., 810 Hesters Crossing Rd., Suite 150, Round Rock, TX 78681
2 shared publications- Juan Murcia-Delso
Universitat Politecnica de Catalunya
2 shared publications
Latest Publications
- 1 August 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 152 (8) , 04026081
Development and Experimental Validation of a Refined Three-Dimensional Strut-and-Tie Model for Pile Caps with Curved-Bar Nodes
This paper presents the results of large-scale tests on two pile cap specimens subjected to concentric loading: one with a square plan and the other with a rectangular plan. During the test...
- 1 August 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 152 (8) , 04026081
Development and Experimental Validation of a Refined Three-Dimensional Strut-and-Tie Model for Pile Caps with Curved-Bar Nodes
This paper presents the results of large-scale tests on two pile cap specimens subjected to concentric loading: one with a square plan and the other with a rectangular plan. During the test...
- 1 July 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 151 (7)
Evaluation and Proposal of Strut-and-Tie Method for the Design of Drilled Shaft Footings
- 1 July 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 151 (7)
Evaluation and Proposal of Strut-and-Tie Method for the Design of Drilled Shaft Footings
- 1 August 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 24 (8)
Modeling Damage and Failure in Pretensioned Concrete Girders Fabricated with Large-Diameter Strands
Pretensioned concrete elements are commonly fabricated with strands 12.7 or 15.2 mm (0.5 or 0.6 in.) in diameter; however, the industry has seen interest in using larger-diameter strands in recent years. The use of larger-diameter strands results in greater transverse tensile stresses within the girder end regions, which may increase cracking at the time of prestress transfer. Such cracks may continue to grow during service and cause durability concerns. Moreover, increased damage around the strands and at the web–flange interfaces may lead to unconventional failure mechanisms, such as anchorage-induced or horizontal shear failures. This paper introduces a modeling approach for investigating the performance of pretensioned girders fabricated with strands 17.8 mm (0.7 in.) in diameter from prestress transfer until failure under shear-critical loading. Data from seven full-scale prestress transfer tests and 10 load tests showed that the model can capture the transfer lengths, end-region stresses, and cracking at prestress transfer as well as load-deflection response and failure modes. Subsequently, three remedial end-region reinforcement details were investigated using the validated approach to examine their efficacy in controlling end-region cracks and stresses.
- 1 August 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 24 (8)
Modeling Damage and Failure in Pretensioned Concrete Girders Fabricated with Large-Diameter Strands
Pretensioned concrete elements are commonly fabricated with strands 12.7 or 15.2 mm (0.5 or 0.6 in.) in diameter; however, the industry has seen interest in using larger-diameter strands in recent years. The use of larger-diameter strands results in greater transverse tensile stresses within the girder end regions, which may increase cracking at the time of prestress transfer. Such cracks may continue to grow during service and cause durability concerns. Moreover, increased damage around the strands and at the web–flange interfaces may lead to unconventional failure mechanisms, such as anchorage-induced or horizontal shear failures. This paper introduces a modeling approach for investigating the performance of pretensioned girders fabricated with strands 17.8 mm (0.7 in.) in diameter from prestress transfer until failure under shear-critical loading. Data from seven full-scale prestress transfer tests and 10 load tests showed that the model can capture the transfer lengths, end-region stresses, and cracking at prestress transfer as well as load-deflection response and failure modes. Subsequently, three remedial end-region reinforcement details were investigated using the validated approach to examine their efficacy in controlling end-region cracks and stresses.
- 1 September 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (9)
Experimental and Numerical Assessment of Corbels Designed Based on Strut-and-Tie Provisions
Reinforced concrete (RC) corbels are short cantilever members that are used to transfer eccentric loads into columns or walls. Due to discontinuity in load and geometry, RC corbels cannot be adequately designed using methods that are based on beam theory. AASHTO LRFD Bridge Design Specifications permit the use of the strut-and-tie method (STM) for designing corbels. However, these specifications also require that the reinforcement details satisfy the requirements of an empirical design method, which prevents the efficient use of STM for such members. Moreover, the crack-control reinforcement requirements in the current STM provisions of AASHTO LRFD have been developed based on studies on deep beams, and the suitability of these provisions for corbels has not been investigated. This paper evaluates the behavior of reinforced concrete corbels designed according to the STM provisions of AASHTO LRFD. To do so, first, the performances of three full-scale corbel specimens designed according to STM were experimentally evaluated. Then, a numerical study using experimentally validated nonlinear finite-element models was conducted to investigate the crack-control reinforcement requirements for RC corbels. The results from the experimental study indicate that the STM provisions of the AASHTO LRFD provide conservative estimates of the load-carrying capacity of RC corbels; however, examination of the smeared node near the corbel-column interface, a check not currently required in AASHTO LRFD, is highly recommended. The results from the numerical study suggest that a reduction in the amount of secondary reinforcement currently required by AASHTO LRFD may be feasible, depending on the reinforcement layout used.
- 1 September 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (9)
Experimental and Numerical Assessment of Corbels Designed Based on Strut-and-Tie Provisions
Reinforced concrete (RC) corbels are short cantilever members that are used to transfer eccentric loads into columns or walls. Due to discontinuity in load and geometry, RC corbels cannot be adequately designed using methods that are based on beam theory. AASHTO LRFD Bridge Design Specifications permit the use of the strut-and-tie method (STM) for designing corbels. However, these specifications also require that the reinforcement details satisfy the requirements of an empirical design method, which prevents the efficient use of STM for such members. Moreover, the crack-control reinforcement requirements in the current STM provisions of AASHTO LRFD have been developed based on studies on deep beams, and the suitability of these provisions for corbels has not been investigated. This paper evaluates the behavior of reinforced concrete corbels designed according to the STM provisions of AASHTO LRFD. To do so, first, the performances of three full-scale corbel specimens designed according to STM were experimentally evaluated. Then, a numerical study using experimentally validated nonlinear finite-element models was conducted to investigate the crack-control reinforcement requirements for RC corbels. The results from the experimental study indicate that the STM provisions of the AASHTO LRFD provide conservative estimates of the load-carrying capacity of RC corbels; however, examination of the smeared node near the corbel-column interface, a check not currently required in AASHTO LRFD, is highly recommended. The results from the numerical study suggest that a reduction in the amount of secondary reinforcement currently required by AASHTO LRFD may be feasible, depending on the reinforcement layout used.
- 1 September 2017
- Published by American Concrete Institute in ACI Structural Journal
- Vol. 114 (5) , 1273-1284
Shear Performance of Pretensioned Concrete I-Girders Employing 0.7 in. (17.8 mm) Strands
- 1 September 2017
- Published by American Concrete Institute in ACI Structural Journal
- Vol. 114 (5) , 1273-1284
Shear Performance of Pretensioned Concrete I-Girders Employing 0.7 in. (17.8 mm) Strands
- 1 January 2017
- Published by Precast/Prestressed Concrete Institute in PCI Journal
- Vol. 62 (6)
Benefits of Using 0.7 in. (18 mm) Diameter Strands in Precast, Pretensioned Girders: A Parametric Investigation
- 1 January 2017
- Published by Precast/Prestressed Concrete Institute in PCI Journal
- Vol. 62 (6)
Benefits of Using 0.7 in. (18 mm) Diameter Strands in Precast, Pretensioned Girders: A Parametric Investigation