Yousun Yi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yousun Yi has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Hyunsu Kim
Structural Specialist, COWI North America Inc., 522 SW Fifth Ave., Portland, OR 97204. ORCID
4 shared publications Oguzhan Bayrak
Univ. of Texas at Austin
4 shared publications- Trevor D. Hrynyk
University of Waterloo
3 shared publications - Juan Murcia-Delso
Universitat Politecnica de Catalunya
2 shared publications - Elias I. Saqan
Univ. of Texas at Austin
1 shared publication - Farid Khosravikia
Department of Civil Architectural and Environmental Engineering, The University of Texas at Austin, 301E E Dean Keeton Street C1700, Austin, Texas 78712 U.S.A.
1 shared publication
Latest Publications
- 1 August 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 152 (8) , 04026081
Development and Experimental Validation of a Refined Three-Dimensional Strut-and-Tie Model for Pile Caps with Curved-Bar Nodes
This paper presents the results of large-scale tests on two pile cap specimens subjected to concentric loading: one with a square plan and the other with a rectangular plan. During the test...
- 1 August 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 152 (8) , 04026081
Development and Experimental Validation of a Refined Three-Dimensional Strut-and-Tie Model for Pile Caps with Curved-Bar Nodes
This paper presents the results of large-scale tests on two pile cap specimens subjected to concentric loading: one with a square plan and the other with a rectangular plan. During the test...
- 29 December 2025
- Published by Elsevier in Engineering Structures
- Vol. 351
Shear behavior of prestressed box beams with high-strength shear reinforcement
- 29 December 2025
- Published by Elsevier in Engineering Structures
- Vol. 351
Shear behavior of prestressed box beams with high-strength shear reinforcement
- 1 July 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 151 (7)
Evaluation and Proposal of Strut-and-Tie Method for the Design of Drilled Shaft Footings
- 1 July 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 151 (7)
Evaluation and Proposal of Strut-and-Tie Method for the Design of Drilled Shaft Footings
- 1 September 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (9)
Experimental and Numerical Assessment of Corbels Designed Based on Strut-and-Tie Provisions
Reinforced concrete (RC) corbels are short cantilever members that are used to transfer eccentric loads into columns or walls. Due to discontinuity in load and geometry, RC corbels cannot be adequately designed using methods that are based on beam theory. AASHTO LRFD Bridge Design Specifications permit the use of the strut-and-tie method (STM) for designing corbels. However, these specifications also require that the reinforcement details satisfy the requirements of an empirical design method, which prevents the efficient use of STM for such members. Moreover, the crack-control reinforcement requirements in the current STM provisions of AASHTO LRFD have been developed based on studies on deep beams, and the suitability of these provisions for corbels has not been investigated. This paper evaluates the behavior of reinforced concrete corbels designed according to the STM provisions of AASHTO LRFD. To do so, first, the performances of three full-scale corbel specimens designed according to STM were experimentally evaluated. Then, a numerical study using experimentally validated nonlinear finite-element models was conducted to investigate the crack-control reinforcement requirements for RC corbels. The results from the experimental study indicate that the STM provisions of the AASHTO LRFD provide conservative estimates of the load-carrying capacity of RC corbels; however, examination of the smeared node near the corbel-column interface, a check not currently required in AASHTO LRFD, is highly recommended. The results from the numerical study suggest that a reduction in the amount of secondary reinforcement currently required by AASHTO LRFD may be feasible, depending on the reinforcement layout used.
- 1 September 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (9)
Experimental and Numerical Assessment of Corbels Designed Based on Strut-and-Tie Provisions
Reinforced concrete (RC) corbels are short cantilever members that are used to transfer eccentric loads into columns or walls. Due to discontinuity in load and geometry, RC corbels cannot be adequately designed using methods that are based on beam theory. AASHTO LRFD Bridge Design Specifications permit the use of the strut-and-tie method (STM) for designing corbels. However, these specifications also require that the reinforcement details satisfy the requirements of an empirical design method, which prevents the efficient use of STM for such members. Moreover, the crack-control reinforcement requirements in the current STM provisions of AASHTO LRFD have been developed based on studies on deep beams, and the suitability of these provisions for corbels has not been investigated. This paper evaluates the behavior of reinforced concrete corbels designed according to the STM provisions of AASHTO LRFD. To do so, first, the performances of three full-scale corbel specimens designed according to STM were experimentally evaluated. Then, a numerical study using experimentally validated nonlinear finite-element models was conducted to investigate the crack-control reinforcement requirements for RC corbels. The results from the experimental study indicate that the STM provisions of the AASHTO LRFD provide conservative estimates of the load-carrying capacity of RC corbels; however, examination of the smeared node near the corbel-column interface, a check not currently required in AASHTO LRFD, is highly recommended. The results from the numerical study suggest that a reduction in the amount of secondary reinforcement currently required by AASHTO LRFD may be feasible, depending on the reinforcement layout used.