Ankush Raina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ankush Raina has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Mir Irfan Ul Haq
Shri Mata Vaishno Devi University
18 shared publications Ankush Anand
School of Mechanical Engineering, Shri Mata Vaishno Devi University, Katra, India
9 shared publicationsKaran Vohra
5 shared publicationsMir Irfan Ul Haq
5 shared publications- Sanjay Mohan
Shri Mata Vaishno Devi University
4 shared publications - Ankush Anand
Shri Mata Vaishno Devi University
3 shared publications
Latest Publications
- 25 February 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 238  (6) , 687-696
High temperature tribological response of Fe-2Cu-0.8C-CaF2 self-lubricating composites at high speeds
In this work, Fe-2Cu-0.8C-CaF2 self-lubricating composites with calcium fluoride solid lubricant (3 □ 12 wt.%) were examined for their friction and wear at 5 and 10 m/s, at 500 °C. Addition of CaF2 decreased density and hardness of composites. During sliding, materials gained weight due to oxidation. Compared to the base matrix (Fe-2Cu-0.8C), composites showed lower weight gain and lower coefficient of friction. Increase in porosity with CaF2 content increased oxidation resulting in higher weight gain and increased friction due to wear debris abrasion. Increase in speed reduced weight gain due to higher material loss. Adhesion was the dominant wear mechanism in base matrix; delamination and wear debris abrasion in composites. Temperature rise at sliding surfaces was theoretically estimated. Increase in speed increased temperature, which reduced friction due to softening and shearing of solid lubricant. Composite with 3 wt.% CaF2 showed least surface damage and 6 wt.% showed lowest coefficient of friction, i.e., lower by 16% and 10% at 5, 10 m/s than base matrix. Tribological response of the composites to a broad range of applied parameters, viz. speed, load and temperature taken from earlier works and present work is briefly summarized. The study suggests the dominant role of CaF2 content and the wear debris in altering the tribological response. Further, the stability of the developed composites at high temperature and high load conditions was also established. The study suggests that the developed composites could serve high-load and high-temperature applications for heavy machinery such as bearings, shafts and gears.
- 25 February 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 238  (6) , 687-696
High temperature tribological response of Fe-2Cu-0.8C-CaF2 self-lubricating composites at high speeds
In this work, Fe-2Cu-0.8C-CaF2 self-lubricating composites with calcium fluoride solid lubricant (3 □ 12 wt.%) were examined for their friction and wear at 5 and 10 m/s, at 500 °C. Addition of CaF2 decreased density and hardness of composites. During sliding, materials gained weight due to oxidation. Compared to the base matrix (Fe-2Cu-0.8C), composites showed lower weight gain and lower coefficient of friction. Increase in porosity with CaF2 content increased oxidation resulting in higher weight gain and increased friction due to wear debris abrasion. Increase in speed reduced weight gain due to higher material loss. Adhesion was the dominant wear mechanism in base matrix; delamination and wear debris abrasion in composites. Temperature rise at sliding surfaces was theoretically estimated. Increase in speed increased temperature, which reduced friction due to softening and shearing of solid lubricant. Composite with 3 wt.% CaF2 showed least surface damage and 6 wt.% showed lowest coefficient of friction, i.e., lower by 16% and 10% at 5, 10 m/s than base matrix. Tribological response of the composites to a broad range of applied parameters, viz. speed, load and temperature taken from earlier works and present work is briefly summarized. The study suggests the dominant role of CaF2 content and the wear debris in altering the tribological response. Further, the stability of the developed composites at high temperature and high load conditions was also established. The study suggests that the developed composites could serve high-load and high-temperature applications for heavy machinery such as bearings, shafts and gears.
- 13 September 2023
- Published by Taylor & Francis
- p. 1-20
3D Printing and New Product Development
New product development process demands technologies which are cost and time effective and at the same time are sustainable too. The technology of three-dimensional (3D) printing offers various advantages to designers to carry out new design processes. This chapter provides an introduction to the technology of 3D printing, various 3D printing technologies, and various material aspects. The advantages and disadvantages of various technologies have been discussed. A section also introduces the linkage between 3D printing and new product development. A discussion on various opportunities and challenges associated with various 3D printing technologies has also been made. This chapter shall help the readers of the book to understand the various basic concepts involved in the area of 3D printing and shall help as a prerequisite to the forthcoming chapters of the book.
- 13 September 2023
- Published by Taylor & Francis
- p. 1-20
3D Printing and New Product Development
New product development process demands technologies which are cost and time effective and at the same time are sustainable too. The technology of three-dimensional (3D) printing offers various advantages to designers to carry out new design processes. This chapter provides an introduction to the technology of 3D printing, various 3D printing technologies, and various material aspects. The advantages and disadvantages of various technologies have been discussed. A section also introduces the linkage between 3D printing and new product development. A discussion on various opportunities and challenges associated with various 3D printing technologies has also been made. This chapter shall help the readers of the book to understand the various basic concepts involved in the area of 3D printing and shall help as a prerequisite to the forthcoming chapters of the book.
- 13 September 2023
- Published by Taylor & Francis
3D Printing and Sustainable Product Development
The text focuses on the role and the importance of 3D printing in new product development processes. It covers various aspects such as the 3D printing revolution and Industry 4.0, sustainability and 3D printing, and economics of 3D printing. It discusses important concepts, including 3D printing, rapid prototyping, mechanical and physical properties of 3D printed parts, nanomaterials, and material aspects of 3D printing. Features 1. Presents recent advances such as Industry 4.0, 4D printing, 3D material mechanical characterization, and printing of advanced materials. 2. Highlights the interdisciplinary aspects of 3D printing, particularly in biomedical, and aerospace engineering. 3. Discusses mechanical and physical properties of 3D printed parts, material aspects, and process parameters. 4. Showcases topics such as rapid prototyping, medical equipment design, and biomimetics related to the role of 3D printing in new product development. 5.Covers applications of 3D printing in diverse areas, including automotive, aerospace engineering, medical, and marine industry. It will serve as an ideal reference text for senior undergraduate, graduate students, and researchers in diverse engineering domains, including manufacturing, mechanical, aerospace, automotive, and industrial.
- 13 September 2023
- Published by Taylor & Francis
3D Printing and Sustainable Product Development
The text focuses on the role and the importance of 3D printing in new product development processes. It covers various aspects such as the 3D printing revolution and Industry 4.0, sustainability and 3D printing, and economics of 3D printing. It discusses important concepts, including 3D printing, rapid prototyping, mechanical and physical properties of 3D printed parts, nanomaterials, and material aspects of 3D printing. Features 1. Presents recent advances such as Industry 4.0, 4D printing, 3D material mechanical characterization, and printing of advanced materials. 2. Highlights the interdisciplinary aspects of 3D printing, particularly in biomedical, and aerospace engineering. 3. Discusses mechanical and physical properties of 3D printed parts, material aspects, and process parameters. 4. Showcases topics such as rapid prototyping, medical equipment design, and biomimetics related to the role of 3D printing in new product development. 5.Covers applications of 3D printing in diverse areas, including automotive, aerospace engineering, medical, and marine industry. It will serve as an ideal reference text for senior undergraduate, graduate students, and researchers in diverse engineering domains, including manufacturing, mechanical, aerospace, automotive, and industrial.
- 1 September 2022
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 10  (3) , 035043
Impact of surface texturing on the tribological behaviour of aluminium-silicon (Al-Si/Al 2 O 3 ) advanced composite under dry and lubricating conditions
In the present work, modification of aluminum-silicon (Al-Si) alloy based advanced composite surface is performed using laser texturing (L T ). Surface texturing (S T ) with different patterns, i.e., dimple (T 1 ), square (T 2 ), triangular (T 3 ), and line hatched (T 4 ) textures are done on the alloy surface and its impact on the mechanism to reduce friction and wear are investigated. The tribo tests are conducted at 10 N load, Hertzian contact pressure (P max ) 708.7 MPa, 1 mm stroke length, frequency 50 Hz and sliding distance (S D ) up to 450 m. The tribological behavior of the non-textured surface (N TS ) and textured surface (T S ) are examined under dry sliding conditions (D SC ) and two lubricating sliding conditions (L SC ) comprising of virgin PAO-4 (Lube-1) and PAO-4 + 1 wt% graphene nanoplatelets (Lube-2). T 2 texture reveals a 49.53%, 69.21% and 44.91% decrease in friction coefficient(COF) and 58.1%, 43.74% and 83.86% decrease in wear volume (W V ) than the N TS for D SC , Lube-1 and,Lube-2, correspondingly. Results show that S T improved friction efficiency, and shortened the running-in period. The current study results help to provide in-depth interpretation of micro-texturing and its relationship w.r.t. tribological characteristics.
- 1 September 2022
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 10  (3) , 035043
Impact of surface texturing on the tribological behaviour of aluminium-silicon (Al-Si/Al 2 O 3 ) advanced composite under dry and lubricating conditions
In the present work, modification of aluminum-silicon (Al-Si) alloy based advanced composite surface is performed using laser texturing (L T ). Surface texturing (S T ) with different patterns, i.e., dimple (T 1 ), square (T 2 ), triangular (T 3 ), and line hatched (T 4 ) textures are done on the alloy surface and its impact on the mechanism to reduce friction and wear are investigated. The tribo tests are conducted at 10 N load, Hertzian contact pressure (P max ) 708.7 MPa, 1 mm stroke length, frequency 50 Hz and sliding distance (S D ) up to 450 m. The tribological behavior of the non-textured surface (N TS ) and textured surface (T S ) are examined under dry sliding conditions (D SC ) and two lubricating sliding conditions (L SC ) comprising of virgin PAO-4 (Lube-1) and PAO-4 + 1 wt% graphene nanoplatelets (Lube-2). T 2 texture reveals a 49.53%, 69.21% and 44.91% decrease in friction coefficient(COF) and 58.1%, 43.74% and 83.86% decrease in wear volume (W V ) than the N TS for D SC , Lube-1 and,Lube-2, correspondingly. Results show that S T improved friction efficiency, and shortened the running-in period. The current study results help to provide in-depth interpretation of micro-texturing and its relationship w.r.t. tribological characteristics.
- 11 August 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 237  (4) , 843-859
Evaluation and prediction of frictional behavior of AA 2024 based hybrid composites using ANN model
The paper investigates the frictional behavior of AA 2024 hybrid aluminum matrix composites reinforced with Zirconium dioxide (ZrO2) and Graphite (Gr). The hybrid composite is fabricated by stir casting technique by using fixed 6 wt. % of ZrO2 and varying 1.5, 3.0 and 4.5 wt. % of Gr reinforcement. The test specimens were fabricated in the form of pins to carryout frictional testing by using Pin-on-disc tribometer under dry and lubricated conditions. Tests were conducted at 15 N load corresponding to 2000 m sliding distance and varying sliding speed of 1 m/s, 2 m/s, 3 m/s and 4 m/s. Coefficient of Friction (COF) increased with the increase in sliding speed for both dry and lubricated conditions but hybrid composite with 3.0 and 4.5 wt. % showed a decrease in COF at 4 m/s sliding speed under lubricated conditions. At higher sliding speed, greater amount of frictional heat is developed which leads to the softening of Gr particles and a solid lubricant layer of Gr along with Polyalphaolefin(PAO) oil reduces the metal-to-metal contact and thus reduces the COF. Maximum COF was observed for 1.5 wt. % Gr reinforcement under dry condition whereas under lubricated conditions pure AA 2024 resulted in maximum COF. Artificial Neural Network (ANN) technique was used for predicting the friction behavior and the confirmatory tests were also performed corresponding to sliding speed of 5 m/s. From the investigations it was revealed that the error in predicted and experimental results is in the acceptable range.
- 11 August 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 237  (4) , 843-859
Evaluation and prediction of frictional behavior of AA 2024 based hybrid composites using ANN model
The paper investigates the frictional behavior of AA 2024 hybrid aluminum matrix composites reinforced with Zirconium dioxide (ZrO2) and Graphite (Gr). The hybrid composite is fabricated by stir casting technique by using fixed 6 wt. % of ZrO2 and varying 1.5, 3.0 and 4.5 wt. % of Gr reinforcement. The test specimens were fabricated in the form of pins to carryout frictional testing by using Pin-on-disc tribometer under dry and lubricated conditions. Tests were conducted at 15 N load corresponding to 2000 m sliding distance and varying sliding speed of 1 m/s, 2 m/s, 3 m/s and 4 m/s. Coefficient of Friction (COF) increased with the increase in sliding speed for both dry and lubricated conditions but hybrid composite with 3.0 and 4.5 wt. % showed a decrease in COF at 4 m/s sliding speed under lubricated conditions. At higher sliding speed, greater amount of frictional heat is developed which leads to the softening of Gr particles and a solid lubricant layer of Gr along with Polyalphaolefin(PAO) oil reduces the metal-to-metal contact and thus reduces the COF. Maximum COF was observed for 1.5 wt. % Gr reinforcement under dry condition whereas under lubricated conditions pure AA 2024 resulted in maximum COF. Artificial Neural Network (ANN) technique was used for predicting the friction behavior and the confirmatory tests were also performed corresponding to sliding speed of 5 m/s. From the investigations it was revealed that the error in predicted and experimental results is in the acceptable range.
- 10 August 2022
- Published by Elsevier in Journal of Orthopaedics
- Vol. 34, 49-60
Tribo-corrosive behavior of additive manufactured parts for orthopaedic applications
- 10 August 2022
- Published by Elsevier in Journal of Orthopaedics
- Vol. 34, 49-60
Tribo-corrosive behavior of additive manufactured parts for orthopaedic applications
- Top Cited PapersOpen Access
- 12 April 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12  (8) , 1323
Nanostructured Coatings: Review on Processing Techniques, Corrosion Behaviour and Tribological Performance
Corrosion and tribology are surface phenomena. Modifying surfaces of materials without resorting to altering their bulk properties is an effective route to alleviate corrosion, friction and wear, encountered in engineering applications. With the advancements in the field of nanotechnology, surface protective coatings with nanomaterials can be readily developed to explore their functionality in mitigating chemical/physical damage of surfaces. Surface protection enhances performance and operating lifetimes of industrial machinery components. This review presents insights on various types of recently developed nanostructured coatings, their synthesis routes, corrosion behaviour and tribological performance. It provides the state-of-the-art information on the development of nanostructured coatings, namely, ceramic coatings, metallic coatings and nanocomposite coatings with metal and polymer matrices. Biomimetic approaches in making nanostructured coatings and challenges encountered in the development of nanostructured coatings are highlighted.
- 12 April 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12  (8) , 1323
Top Cited PapersOpen AccessNanostructured Coatings: Review on Processing Techniques, Corrosion Behaviour and Tribological Performance
Corrosion and tribology are surface phenomena. Modifying surfaces of materials without resorting to altering their bulk properties is an effective route to alleviate corrosion, friction and wear, encountered in engineering applications. With the advancements in the field of nanotechnology, surface protective coatings with nanomaterials can be readily developed to explore their functionality in mitigating chemical/physical damage of surfaces. Surface protection enhances performance and operating lifetimes of industrial machinery components. This review presents insights on various types of recently developed nanostructured coatings, their synthesis routes, corrosion behaviour and tribological performance. It provides the state-of-the-art information on the development of nanostructured coatings, namely, ceramic coatings, metallic coatings and nanocomposite coatings with metal and polymer matrices. Biomimetic approaches in making nanostructured coatings and challenges encountered in the development of nanostructured coatings are highlighted.
- 12 October 2021
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 7  (4) , 1-12
Rheological and Tribological Behavior of Sunflower Oil: Effect of Chemical Modification and Tungsten DiSulfide Nanoparticles
- 12 October 2021
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 7  (4) , 1-12
Rheological and Tribological Behavior of Sunflower Oil: Effect of Chemical Modification and Tungsten DiSulfide Nanoparticles
- 4 October 2021
- Published by SAGE Publications in Tribology - Materials, Surfaces & Interfaces
- Vol. 16  (1) , 34-56
Dispersion stability of nano additives in lubricating oils – an overview of mechanisms, theories and methodologies
With the advancement in the field of nanotechnology, various researchers have reported an improvement in the friction and wear behaviour of different lubricating oils by the addition of different nano additives. However, the stability of these nano additives remains a challenge. In this paper, the dispersion stability of various nano additives in lubricating oils has been studied in detail. The paper aims to summarize various dispersion stability theories and several methods reported in the literature to improve dispersion stability. Apart from this, a special focus has been laid to highlight the various surfactants used to improve the dispersion stability, particularly the tribological properties. The literature suggests that although a number of studies have been carried out to study the effect of surfactant addition on dispersion stability, however, future developments could be focused to improve the dispersion stability of the existing mono and hybrid nano fluids and their underlying mechanisms. Abbreviations: SWCNH, single-walled carbon nano-horns; PAO, poly alpha olefin; MoS2, molybdenum di sulphide; H, Hamaker constant, MWCNTs, multi-walled carbon nanotubes; GNF, graphene nanoflakes; DLVO, Derjaguin and Landau Verway and Overbeek; DLS, dynamic light scattering; HLB, hydrophobic lyophilic balance; FERTEM, freeze etching replication transmission electron microscope; SDS, sodium dodecyl sulphate; PTFE, polytetrafluoroethylene; FTIR, Fourier-transform infrared spectroscopy; TBAAc, tetra butyl ammonium acetate; THF, tetrahydrofurane; UV–Vis, ultraviolet visible light; SEM, scanning electron microscope; TEM, transmission electron microscope GRAPHICAL ABSTRACT
- 4 October 2021
- Published by SAGE Publications in Tribology - Materials, Surfaces & Interfaces
- Vol. 16  (1) , 34-56
Dispersion stability of nano additives in lubricating oils – an overview of mechanisms, theories and methodologies
With the advancement in the field of nanotechnology, various researchers have reported an improvement in the friction and wear behaviour of different lubricating oils by the addition of different nano additives. However, the stability of these nano additives remains a challenge. In this paper, the dispersion stability of various nano additives in lubricating oils has been studied in detail. The paper aims to summarize various dispersion stability theories and several methods reported in the literature to improve dispersion stability. Apart from this, a special focus has been laid to highlight the various surfactants used to improve the dispersion stability, particularly the tribological properties. The literature suggests that although a number of studies have been carried out to study the effect of surfactant addition on dispersion stability, however, future developments could be focused to improve the dispersion stability of the existing mono and hybrid nano fluids and their underlying mechanisms. Abbreviations: SWCNH, single-walled carbon nano-horns; PAO, poly alpha olefin; MoS2, molybdenum di sulphide; H, Hamaker constant, MWCNTs, multi-walled carbon nanotubes; GNF, graphene nanoflakes; DLVO, Derjaguin and Landau Verway and Overbeek; DLS, dynamic light scattering; HLB, hydrophobic lyophilic balance; FERTEM, freeze etching replication transmission electron microscope; SDS, sodium dodecyl sulphate; PTFE, polytetrafluoroethylene; FTIR, Fourier-transform infrared spectroscopy; TBAAc, tetra butyl ammonium acetate; THF, tetrahydrofurane; UV–Vis, ultraviolet visible light; SEM, scanning electron microscope; TEM, transmission electron microscope GRAPHICAL ABSTRACT
- Open Access
- 29 May 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11  (6) , 1438
Nanodiamond Particles as Secondary Additive for Polyalphaolefin Oil Lubrication of Steel–Aluminium Contact
Nanodiamond (ND) particles are effective lubricant additives. Attention of research has shifted towards investigating the particles as secondary additives. ND particles provide more benefits as secondary additives than as the sole lubricant additive for steel–steel contacts. In this work, the influence of ND particles as secondary additives on oil lubrication of steel–aluminium tribopair (hard–soft contact) was examined. AISI 52100 steel balls were slid against AA2024 aluminium alloy discs, in the presence of polyalphaolefin (PAO) base oil, in boundary lubrication regime (applied normal load: 10 N to 50 N). Primary additives were copper oxide (CuO) and hexagonal boron nitride (h-BN) nanoparticles. The addition of ND particles to PAO, with CuO and h-BN as primary additives, at the lowest applied normal load of 10 N: (i) decreased the volumetric wear of the aluminium discs by 28% and 63%, respectively, and (ii) decreased the coefficient of friction by 15% and 33%, respectively. At the highest applied normal load of 50 N, it: (i) decreased the volumetric wear of the aluminium discs by 20% and 38%, respectively, and (ii) decreased the coefficient of friction by 5.4% and 8%, respectively. ND particles as secondary additives significantly reduce energy loss and power loss as a consequence of an effective reduction in friction during sliding. Unique characteristics of ND particles—such as their (a) physicochemical and thermal properties, (b) ball bearing and polishing effects and (c) synergistic interaction with primary additives to form stable tribofilms—enhance the lubrication performance of steel–aluminium contact. ND particles in combination with h-BN nanoparticles showed the best performance, due to better synergy between the primary additive and the secondary additive. Results from the investigation indicate that ND particles taken as secondary additives in small amount (0.2 wt%) can improve oil lubrication performance of hard–soft contacts in engineering systems.
- 29 May 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11  (6) , 1438
Open AccessNanodiamond Particles as Secondary Additive for Polyalphaolefin Oil Lubrication of Steel–Aluminium Contact
Nanodiamond (ND) particles are effective lubricant additives. Attention of research has shifted towards investigating the particles as secondary additives. ND particles provide more benefits as secondary additives than as the sole lubricant additive for steel–steel contacts. In this work, the influence of ND particles as secondary additives on oil lubrication of steel–aluminium tribopair (hard–soft contact) was examined. AISI 52100 steel balls were slid against AA2024 aluminium alloy discs, in the presence of polyalphaolefin (PAO) base oil, in boundary lubrication regime (applied normal load: 10 N to 50 N). Primary additives were copper oxide (CuO) and hexagonal boron nitride (h-BN) nanoparticles. The addition of ND particles to PAO, with CuO and h-BN as primary additives, at the lowest applied normal load of 10 N: (i) decreased the volumetric wear of the aluminium discs by 28% and 63%, respectively, and (ii) decreased the coefficient of friction by 15% and 33%, respectively. At the highest applied normal load of 50 N, it: (i) decreased the volumetric wear of the aluminium discs by 20% and 38%, respectively, and (ii) decreased the coefficient of friction by 5.4% and 8%, respectively. ND particles as secondary additives significantly reduce energy loss and power loss as a consequence of an effective reduction in friction during sliding. Unique characteristics of ND particles—such as their (a) physicochemical and thermal properties, (b) ball bearing and polishing effects and (c) synergistic interaction with primary additives to form stable tribofilms—enhance the lubrication performance of steel–aluminium contact. ND particles in combination with h-BN nanoparticles showed the best performance, due to better synergy between the primary additive and the secondary additive. Results from the investigation indicate that ND particles taken as secondary additives in small amount (0.2 wt%) can improve oil lubrication performance of hard–soft contacts in engineering systems.