Xiaomi Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaomi Zhang has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Mercouri G. Kanatzidis
Northwestern University
3 shared publications - Vinayak P. Dravid
Northwestern University
3 shared publications Chris Wolverton
Department of Materials Science and Engineering,Northwestern University,Evanston, IL 60208,USA
2 shared publications- Chris Wolverton
International Institute for Nanotechnology Northwestern University Evanston Illinois USA
2 shared publications - Ctirad Uher
Department of Physics University of Michigan Ann Arbor Michigan USA
2 shared publications Gangjian Tan
Department of Chemistry,Northwestern University,Evanston, IL 60208,USA
2 shared publications
Latest Publications
- 1 July 2019
- Published by Wiley in Advanced Energy Materials
- Vol. 9 (30)
High Thermoelectric Performance in PbSe–NaSbSe2 Alloys from Valence Band Convergence and Low Thermal Conductivity
PbSe is an attractive thermoelectric material due to its favorable electronic structure, high melting point, and lower cost compared to PbTe. Herein, the hitherto unexplored alloys of PbSe with NaSbSe2 (NaPbmSbSem+2) are described and the most promising p‐type PbSe‐based thermoelectrics are found among them. Surprisingly, it is observed that below 500 K, NaPbmSbSem+2 exhibits unorthodox semiconducting‐like electrical conductivity, despite possessing degenerate carrier densities of ≈1020 cm−3. It is shown that the peculiar behavior derives from carrier scattering by the grain boundaries. It is further demonstrated that the high solubility of NaSbSe2 in PbSe augments both the thermoelectric properties while maintaining a rock salt structure. Namely, density functional theory calculations and photoemission spectroscopy demonstrate that introduction of NaSbSe2 lowers the energy separation between the L‐ and Σ‐valence bands and enhances the power factors under 700 K. The crystallographic disorder of Na+, Pb2+, and Sb3+ moreover provides exceptionally strong point defect phonon scattering yielding low lattice thermal conductivities of 1–0.55 W m‐1 K‐1 between 400 and 873 K without nanostructures. As a consequence, NaPb10SbSe12 achieves maximum ZT ≈1.4 near 900 K when optimally doped. More importantly, NaPb10SbSe12 maintains high ZT across a broad temperature range, giving an estimated record ZTavg of ≈0.64 between 400 and 873 K, a significant improvement over existing p‐type PbSe thermoelectrics.
- 1 July 2019
- Published by Wiley in Advanced Energy Materials
- Vol. 9 (30)
High Thermoelectric Performance in PbSe–NaSbSe2 Alloys from Valence Band Convergence and Low Thermal Conductivity
PbSe is an attractive thermoelectric material due to its favorable electronic structure, high melting point, and lower cost compared to PbTe. Herein, the hitherto unexplored alloys of PbSe with NaSbSe2 (NaPbmSbSem+2) are described and the most promising p‐type PbSe‐based thermoelectrics are found among them. Surprisingly, it is observed that below 500 K, NaPbmSbSem+2 exhibits unorthodox semiconducting‐like electrical conductivity, despite possessing degenerate carrier densities of ≈1020 cm−3. It is shown that the peculiar behavior derives from carrier scattering by the grain boundaries. It is further demonstrated that the high solubility of NaSbSe2 in PbSe augments both the thermoelectric properties while maintaining a rock salt structure. Namely, density functional theory calculations and photoemission spectroscopy demonstrate that introduction of NaSbSe2 lowers the energy separation between the L‐ and Σ‐valence bands and enhances the power factors under 700 K. The crystallographic disorder of Na+, Pb2+, and Sb3+ moreover provides exceptionally strong point defect phonon scattering yielding low lattice thermal conductivities of 1–0.55 W m‐1 K‐1 between 400 and 873 K without nanostructures. As a consequence, NaPb10SbSe12 achieves maximum ZT ≈1.4 near 900 K when optimally doped. More importantly, NaPb10SbSe12 maintains high ZT across a broad temperature range, giving an estimated record ZTavg of ≈0.64 between 400 and 873 K, a significant improvement over existing p‐type PbSe thermoelectrics.
- 14 May 2019
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 25 (4) , 831-839
Ion Beam Induced Artifacts in Lead-Based Chalcogenides
Metal chalcogenides have attracted great attention because of their broad applications. It has been well acknowledged that microstructure can alter the intrinsic properties and performance of metal chalcogenides. The structure–property–performance relationships can be investigated at atomic scale with scanning transmission and transmission electron microscopy (STEM and TEM). Nevertheless, careful specimen preparation is paramount for accurate analyses and interpretations. In this work, we compare the effects of a variety of well-established TEM specimen preparation methods on the observed microstructure of an ingot stoichiometric lead telluride (PbTe). Most importantly, from aberration corrected STEM and first principles calculations, we discovered that argon (Ar) ion milling can lead to surface irradiation damage in the form of Pb vacancy clusters and self-interstitial atom (SIA) clusters. The SIA clusters appear as orthogonal nanoscale features when characterized along the crystal orientation of the rock salt structured PbTe. This obfuscates the interpretation of the intrinsic microstructure of metal chalcogenides, especially lead chalcogenides. We demonstrate that with sufficiently low energy (300 eV) Ar ion cleaning or appropriate high-temperature annealing, the surface damage layer can be properly cleaned and the orthogonal nanoscale features are significantly reduced. This reveals the materials’ intrinsic structure and can be used as the standard protocol for future TEM specimen preparation of lead-based chalcogenide materials.
- 14 May 2019
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 25 (4) , 831-839
Ion Beam Induced Artifacts in Lead-Based Chalcogenides
Metal chalcogenides have attracted great attention because of their broad applications. It has been well acknowledged that microstructure can alter the intrinsic properties and performance of metal chalcogenides. The structure–property–performance relationships can be investigated at atomic scale with scanning transmission and transmission electron microscopy (STEM and TEM). Nevertheless, careful specimen preparation is paramount for accurate analyses and interpretations. In this work, we compare the effects of a variety of well-established TEM specimen preparation methods on the observed microstructure of an ingot stoichiometric lead telluride (PbTe). Most importantly, from aberration corrected STEM and first principles calculations, we discovered that argon (Ar) ion milling can lead to surface irradiation damage in the form of Pb vacancy clusters and self-interstitial atom (SIA) clusters. The SIA clusters appear as orthogonal nanoscale features when characterized along the crystal orientation of the rock salt structured PbTe. This obfuscates the interpretation of the intrinsic microstructure of metal chalcogenides, especially lead chalcogenides. We demonstrate that with sufficiently low energy (300 eV) Ar ion cleaning or appropriate high-temperature annealing, the surface damage layer can be properly cleaned and the orthogonal nanoscale features are significantly reduced. This reveals the materials’ intrinsic structure and can be used as the standard protocol for future TEM specimen preparation of lead-based chalcogenide materials.
- 13 August 2018
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 11 (11) , 3220-3230
Soft phonon modes from off-center Ge atoms lead to ultralow thermal conductivity and superior thermoelectric performance in n-type PbSe–GeSe
Historically PbSe has underperformed PbTe in thermoelectric efficiency and has been regarded as an inferior relative to its telluride congener. However, the fifty-fold greater natural abundance of Se relative to Te makes PbSe appealing as a thermoelectric material. We report that the n-type GeSe-alloyed PbSe system achieves a peak figure of merit, ZT, of ∼1.54 at 773 K and maintains ZT values above 1.2 over a broad temperature range from 623 K to 923 K. The highest performing composition is Sb-doped PbSe–12%GeSe, which exhibits an ultralow lattice thermal conductivity of ∼0.36 W m−1 K−1 at 573 K, close to the limit of amorphous PbSe. Theoretical studies reveal that the alloyed Ge2+ atoms prefer to stay at off-center lattice positions, inducing low frequency modes. The Ge atoms also cause the unexpected behavior where the next nearest atom neighbors (6 Pb atoms) oscillate at lower frequencies than in pure PbSe leading to a large reduction of the Debye temperature and acoustic phonon velocity. The Pb0.9955Sb0.0045Se–12%GeSe system also shows Ge-rich precipitates and many aligned dislocations within its microstructure which also contribute to phonon scattering. The resultant average ZT (ZTavg), a broad measure of the material's potential for functional thermoelectric modules, is 1.06 from 400 K to 800 K, the highest among all previously reported n- and p-type PbSe. This value matches or exceeds even those of the best n-type PbTe-based thermoelectric materials.
- 13 August 2018
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 11 (11) , 3220-3230
Soft phonon modes from off-center Ge atoms lead to ultralow thermal conductivity and superior thermoelectric performance in n-type PbSe–GeSe
Historically PbSe has underperformed PbTe in thermoelectric efficiency and has been regarded as an inferior relative to its telluride congener. However, the fifty-fold greater natural abundance of Se relative to Te makes PbSe appealing as a thermoelectric material. We report that the n-type GeSe-alloyed PbSe system achieves a peak figure of merit, ZT, of ∼1.54 at 773 K and maintains ZT values above 1.2 over a broad temperature range from 623 K to 923 K. The highest performing composition is Sb-doped PbSe–12%GeSe, which exhibits an ultralow lattice thermal conductivity of ∼0.36 W m−1 K−1 at 573 K, close to the limit of amorphous PbSe. Theoretical studies reveal that the alloyed Ge2+ atoms prefer to stay at off-center lattice positions, inducing low frequency modes. The Ge atoms also cause the unexpected behavior where the next nearest atom neighbors (6 Pb atoms) oscillate at lower frequencies than in pure PbSe leading to a large reduction of the Debye temperature and acoustic phonon velocity. The Pb0.9955Sb0.0045Se–12%GeSe system also shows Ge-rich precipitates and many aligned dislocations within its microstructure which also contribute to phonon scattering. The resultant average ZT (ZTavg), a broad measure of the material's potential for functional thermoelectric modules, is 1.06 from 400 K to 800 K, the highest among all previously reported n- and p-type PbSe. This value matches or exceeds even those of the best n-type PbTe-based thermoelectric materials.
- 6 June 2018
- Published by Wiley in Advanced Functional Materials
- Vol. 28 (31)
High Thermoelectric Performance in Supersaturated Solid Solutions and Nanostructured n‐Type PbTe–GeTe
Sb‐doped and GeTe‐alloyed n‐type thermoelectric materials that show an excellent figure of merit ZT in the intermediate temperature range (400–800 K) are reported. The synergistic effect of favorable changes to the band structure resulting in high Seebeck coefficient and enhanced phonon scattering by point defects and nanoscale precipitates resulting in reduction of thermal conductivity are demonstrated. The samples can be tuned as single‐phase solid solution (SS) or two‐phase system with nanoscale precipitates (Nano) based on the annealing processes. The GeTe alloying results in band structure modification by widening the bandgap and increasing the density‐of‐states effective mass of PbTe, resulting in significantly enhanced Seebeck coefficients. The nanoscale precipitates can improve the power factor in the low temperature range and further reduce the lattice thermal conductivity (κlat). Specifically, the Seebeck coefficient of Pb0.988Sb0.012Te–13%GeTe–Nano approaches −280 µV K−1 at 673 K with a low κlat of 0.56 W m−1 K−1 at 573 K. Consequently, a peak ZT value of 1.38 is achieved at 623 K. Moreover, a high average ZTavg value of ≈1.04 is obtained in the temperature range from 300 to 773 K for n‐type Pb0.988Sb0.012Te–13%GeTe–Nano.
- 6 June 2018
- Published by Wiley in Advanced Functional Materials
- Vol. 28 (31)
High Thermoelectric Performance in Supersaturated Solid Solutions and Nanostructured n‐Type PbTe–GeTe
Sb‐doped and GeTe‐alloyed n‐type thermoelectric materials that show an excellent figure of merit ZT in the intermediate temperature range (400–800 K) are reported. The synergistic effect of favorable changes to the band structure resulting in high Seebeck coefficient and enhanced phonon scattering by point defects and nanoscale precipitates resulting in reduction of thermal conductivity are demonstrated. The samples can be tuned as single‐phase solid solution (SS) or two‐phase system with nanoscale precipitates (Nano) based on the annealing processes. The GeTe alloying results in band structure modification by widening the bandgap and increasing the density‐of‐states effective mass of PbTe, resulting in significantly enhanced Seebeck coefficients. The nanoscale precipitates can improve the power factor in the low temperature range and further reduce the lattice thermal conductivity (κlat). Specifically, the Seebeck coefficient of Pb0.988Sb0.012Te–13%GeTe–Nano approaches −280 µV K−1 at 673 K with a low κlat of 0.56 W m−1 K−1 at 573 K. Consequently, a peak ZT value of 1.38 is achieved at 623 K. Moreover, a high average ZTavg value of ≈1.04 is obtained in the temperature range from 300 to 773 K for n‐type Pb0.988Sb0.012Te–13%GeTe–Nano.
- Top Cited Papers
- 7 July 2016
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 138 (28) , 8875-8882
Distinct Impact of Alkali-Ion Doping on Electrical Transport Properties of Thermoelectric p-Type Polycrystalline SnSe
Recent findings about ultrahigh thermoelectric performance in SnSe single crystals have stimulated the related researches on this simple binary compound, which are most devoted to its polycrystalline counterparts with a focus on electrical property enhancement by effective doping. This work systematically investigated the thermoelectric proper-ties of polycrystalline SnSe doped with three alkali metals (Li, Na and K). It is found that Na has the best doping effi-ciency, leading to an increase in hole concentration from 3.2×1017 to 4.4×1019 cm-3 at room temperature, accompanied with a drop in Seebeck coefficient from 480 to 142 μV/K. An equivalent single parabolic band model was found ade-quate to capture the variation tendency of Seebeck coefficient with doping levels within a wide range. A mixed scattering of carriers by acoustic phonons and grain boundaries is suitable for numerically understanding the temperature-dependence of carrier mobility. A maximum ZT of ~0.8 was achieved in 1% Na- or K-doped SnSe at 800 K. Possible strategies to improve the mobility and ZT of polycrystals were also proposed.
- 7 July 2016
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 138 (28) , 8875-8882
Top Cited PapersDistinct Impact of Alkali-Ion Doping on Electrical Transport Properties of Thermoelectric p-Type Polycrystalline SnSe
Recent findings about ultrahigh thermoelectric performance in SnSe single crystals have stimulated the related researches on this simple binary compound, which are most devoted to its polycrystalline counterparts with a focus on electrical property enhancement by effective doping. This work systematically investigated the thermoelectric proper-ties of polycrystalline SnSe doped with three alkali metals (Li, Na and K). It is found that Na has the best doping effi-ciency, leading to an increase in hole concentration from 3.2×1017 to 4.4×1019 cm-3 at room temperature, accompanied with a drop in Seebeck coefficient from 480 to 142 μV/K. An equivalent single parabolic band model was found ade-quate to capture the variation tendency of Seebeck coefficient with doping levels within a wide range. A mixed scattering of carriers by acoustic phonons and grain boundaries is suitable for numerically understanding the temperature-dependence of carrier mobility. A maximum ZT of ~0.8 was achieved in 1% Na- or K-doped SnSe at 800 K. Possible strategies to improve the mobility and ZT of polycrystals were also proposed.
- 1 May 2016
- Published by Elsevier in Ecological Modelling
- Vol. 328, 136-147
A modeling study examining the impact of nutrient boundaries on primary production on the Louisiana continental shelf
- 1 May 2016
- Published by Elsevier in Ecological Modelling
- Vol. 328, 136-147
A modeling study examining the impact of nutrient boundaries on primary production on the Louisiana continental shelf