Devendra Khatiwada
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Devendra Khatiwada has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Jae-Hyun Ryou
Department of Mechanical and Aerospace Engineering University of Houston Houston Texas USA
2 shared publications - Monika Rathi
Department of Mechanical Engineering
2 shared publications - Pavel Dutta
Department of Mechanical Engineering
2 shared publications - Sara Pouladi
Department of Mechanical Engineering, University of Houston 1 , Houston, Texas 77204-4006, USA
2 shared publications - Venkat Selvamanickam
University of Houston
2 shared publications - Abu Farzan Mitul
Health and Civil Sector, Leidos, Reston, VA 20190, USA
1 shared publication
Latest Publications
- Open Access
- 23 July 2020
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 28 (11) , 1107-1119
High‐efficiency single‐junction p‐i‐n GaAs solar cell on roll‐to‐roll epi‐ready flexible metal foils for low‐cost photovoltaics
We demonstrate the fabrication and characterization of high‐efficiency, single‐junction p‐i‐n GaAs solar cells, on flexible metal foil with epi‐ready buffer via roll‐to‐roll fabrication. Single‐junction p‐i‐n GaAs solar cells were fabricated using metal–organic chemical vapor deposition (MOCVD). An efficiency greater than 13% was obtained at 1 sun, which is the highest reported efficiency on GaAs photovoltaics directly deposited on metal tapes. This exceeds our previously reported study showcasing 11.5% efficiency on single‐junction p‐n solar cell structure. Improved morphology of p‐i‐n structure compared with p‐n is explained by atomic force microscopy (AFM), scanning electron microscopy (SEM), and helium ion microscopy (HIM) measurements. Time‐of‐flight secondary ion mass spectrometry (TOF‐SIMS) analysis showed reduced Zn diffusion in p‐i‐n cell compared with the p‐n cell. We attribute the improvement in efficiency of p‐i‐n cells on flexible metal tapes to the quality of the junction, surface morphology, controlled diffusion of species within the active layers, and increase in absorption due to the optimized intrinsic layer thickness.
- 23 July 2020
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 28 (11) , 1107-1119
Open AccessHigh‐efficiency single‐junction p‐i‐n GaAs solar cell on roll‐to‐roll epi‐ready flexible metal foils for low‐cost photovoltaics
We demonstrate the fabrication and characterization of high‐efficiency, single‐junction p‐i‐n GaAs solar cells, on flexible metal foil with epi‐ready buffer via roll‐to‐roll fabrication. Single‐junction p‐i‐n GaAs solar cells were fabricated using metal–organic chemical vapor deposition (MOCVD). An efficiency greater than 13% was obtained at 1 sun, which is the highest reported efficiency on GaAs photovoltaics directly deposited on metal tapes. This exceeds our previously reported study showcasing 11.5% efficiency on single‐junction p‐n solar cell structure. Improved morphology of p‐i‐n structure compared with p‐n is explained by atomic force microscopy (AFM), scanning electron microscopy (SEM), and helium ion microscopy (HIM) measurements. Time‐of‐flight secondary ion mass spectrometry (TOF‐SIMS) analysis showed reduced Zn diffusion in p‐i‐n cell compared with the p‐n cell. We attribute the improvement in efficiency of p‐i‐n cells on flexible metal tapes to the quality of the junction, surface morphology, controlled diffusion of species within the active layers, and increase in absorption due to the optimized intrinsic layer thickness.
- 15 April 2019
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 2 (5) , 3114-3119
Passivation Studies on Single-Junction GaAs Thin Film Solar Cells on Flexible Metal Tapes for Low-Cost Photovoltaics
- 15 April 2019
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 2 (5) , 3114-3119
Passivation Studies on Single-Junction GaAs Thin Film Solar Cells on Flexible Metal Tapes for Low-Cost Photovoltaics
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 866-868
Flexible GaAs Single-Junction Solar Cells Based on Single-Crystal-Like Thin-Film Materials Directly Grown on Metal Tapes
We demonstrate flexible single-junction III-V solar cells based on single-crystal-like GaAs thin films directly grown on a metal tape. The epitaxial (Al)GaAs thin-film structures are developed on flexible polycrystalline Hastelloy tapes using crystallinity-transformational buffer layers for photovoltaic devices with front illumination geometry. The GaAs solar cell shows promising photovoltaic characteristics under AM 1.5G 1-Sun illumination. An open-circuit voltage of 330mV, a short circuit current of 21mA/cm 2 , and a fill factor of 73 result in a conversion efficiency of ~5%. Further improvement in semiconductor thin films quality, device design and fabrication process optimization would improve the device performance characteristics. This new technology has the potential for next-generation low-cost and high efficiency flexible photovoltaic devices.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 866-868
Flexible GaAs Single-Junction Solar Cells Based on Single-Crystal-Like Thin-Film Materials Directly Grown on Metal Tapes
We demonstrate flexible single-junction III-V solar cells based on single-crystal-like GaAs thin films directly grown on a metal tape. The epitaxial (Al)GaAs thin-film structures are developed on flexible polycrystalline Hastelloy tapes using crystallinity-transformational buffer layers for photovoltaic devices with front illumination geometry. The GaAs solar cell shows promising photovoltaic characteristics under AM 1.5G 1-Sun illumination. An open-circuit voltage of 330mV, a short circuit current of 21mA/cm 2 , and a fill factor of 73 result in a conversion efficiency of ~5%. Further improvement in semiconductor thin films quality, device design and fabrication process optimization would improve the device performance characteristics. This new technology has the potential for next-generation low-cost and high efficiency flexible photovoltaic devices.
- 11 August 2015
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 119 (33) , 18992-19000
Improved Performance for Inverted Organic Photovoltaics via Spacer between Benzodithiophene and Benzothiazole in Polymers
- 11 August 2015
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 119 (33) , 18992-19000
Improved Performance for Inverted Organic Photovoltaics via Spacer between Benzodithiophene and Benzothiazole in Polymers