CMChristos Monokroussos

Christos Monokroussos

*This is an algorithmically generated author record based on publicly available information.

Christos Monokroussos has a total of 84 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Developing a New I‐V Translation Methodology in Accordance With IEC 60891:2021 Correction Procedure 1 and 2

    by Wenhao Xu, Yating Zhang, Mengdi Liu, Christos Monokroussos, Werner Herrmann, Giorgio Bardizza, Harald Müllejans

    Accurate translation of photovoltaic (PV) module I‐V curves under varying operating conditions is essential for evaluating module performance and ensuring reliable energy output predictions. This study proposes a hybrid correction procedure (HCP) for I‐V curves, utilizing a four‐parameter Gompertz model to integrate the strengths of CP1 and CP2, thereby unifying the two approaches into a cohesive framework. It further evaluates the performance of HCP alongside existing correction methods (CP1 and CP2) across a broad range of irradiance ( G ) and module temperature ( T m ) conditions. CP1 demonstrates the highest accuracy in P MAX correction, with RMSE values consistently below 0.50% for most modules, but fails to generate complete I‐V curves when translating from low to high‐irradiance levels. CP2, while achieving superior accuracy in V OC correction, struggles with low‐ R sh modules, leading to distorted I‐V curves and reduced accuracy in P MAX and I SC . The proposed HCP method successfully integrates the strengths of CP1 and CP2. It achieves I SC results comparable to CP1, V OC results similar to CP2, and significantly lower RMSE in P MAX compared to CP2, particularly under challenging low‐ R sh and high‐ R S conditions. These findings validate the effectiveness of HCP as a robust alternative correction method for improving the accuracy of I‐V curve translations under diverse real‐world operating conditions. This work provides a pathway to more accurate PV module performance analysis and highlights the importance of addressing R sh and R S effects in future correction procedures.


  • Performance evaluation of procedures used to correct measured I‐V characteristics of photovoltaic modules for temperature and irradiance

    by Wenhao Xu, Christos Monokroussos, Harald Müllejans, Werner Herrmann

    IEC 60891 ed.3 published in 2021 has defined four standard I‐V characteristics correction procedures numbered 1 through 4. The aim of this work is to evaluate these four I‐V translation methods. The results show that correction procedure 1 (CP1) and 2 (CP2) work well over a broad range of irradiances and temperatures. However, CP1 requires I‐V curves being measured adequately down to negative current regime at low‐irradiance levels and CP2 is not so suitable for low shunt‐resistance modules; both also require a set of correction parameters. Based on our performance analysis, a new method based on CP2 is introduced to improve the correction performance for low shunt‐resistance modules; the mean bias error (MBE) value of maximum power (PMAX) improved from −10.26% to −1.32%. Correction procedure 3 (CP3) employs a drastically different correction procedure as compared with the other CPs. This work shows that CP3 works well over a broad range of irradiances and temperatures, but significant distortion of the corrected I‐V curves may occur when extrapolation is required. Correction procedure 4 (CP4) requires only a single I‐V curve and shows generally good results in short‐circuit current (ISC) but worse agreement in open‐circuit voltage (VOC) and PMAX.


  • Open Access

    Energy performance of commercial c-Si PV modules in accordance with IEC 61853-1, -2 and impact on the annual specific yield

    by Christos Monokroussos, Yating Zhang, Eleanor W. Lee, Frank Xu, Allen Zhou, Yichi Zhang, Werner Herrmann

    As energy yields of photovoltaic modules are highly related to local climate and ambient conditions, it is necessary to assess the energy-yield performance of PV modules under various operating conditions. This work compares commercial crystalline silicon (c-Si) based PV modules (including mono c-Si Al BSF, mono c-Si PERC, multi-crystalline (mc-Si) Al BSF, and n-type c-Si solar cells) sampled from 27 PV module manufacturers located in the Asia-Pacific region between 2016 and 2022. Several test items were compared including: (i) light-induced degradation (LID), (ii) irradiance-temperature-efficiency (GTE) matrix, (iii) angular response and (iv) temperature coefficients, which are correspondingly performed according to IEC 61215-1, -1-1, -2 and IEC 61853-1, -2. The coefficient of variation (CoV) was calculated to express the module-to-module differences within similar technology types. Benefiting from the technological innovation of c-Si based PV modules, emerging PV modules feature better performance in some extreme ambient conditions, such as low irradiance, high ambient temperature, and high ratio of diffuse irradiance. The analysis of CoV indicates that the difference of irradiance-dependent and thermal behavior between modules within the same technology may exceed the differences between different technologies. Using synthetic hourly meteorological data of 5 sites from MeteoNorm in PVsyst, the annual specific yield of four technology groups of PV modules were simulated and compared. Overall, it is shown that the maximum differences as large as 7.34% in terms of PV module's specific yield are expected within same PV technology, which exceeds the maximum difference of 2.16% obtained for specific yields of different PV technologies.


  • Interlaboratory comparison of voltage sweep methods used for the electrical characterization of encapsulated high‐efficiency c‐Si solar cells

    by Yating Zhang, Christos Monokroussos, Harrison Wilterdink, Harald Müllejans, Diego Pavanello, Masahiro Yoshita, Kengo Yamagoe, Klaus Ramspeck, David Hinken, Karsten Bothe, et al.

    This work presents the comparison of measurement results for four types of encapsulated high‐efficiency c‐Si solar cells measured by 10 laboratories based in Asia, Europe and North America utilizing a wide range of voltage sweeping methods, which include well‐established procedures that represent good industry practice, as well as recently introduced ones that have not been verified yet. The aim of the round‐robin interlaboratory comparison was to examine the measurement comparability of different laboratories with respect to their measurement methods of high‐efficiency solar cells. A proficiency test was employed to examine the consistency of results and their corresponding uncertainties. The short‐circuit current (ISC) under STC measured by four accredited laboratories was firstly compared. In order to investigate the consistency related to the high device capacitance, the value of the ISC was fixed for all 10 participants. The results of all participant laboratories—compared via En number analysis—generally remained well within [−1; 1], thus indicating consistency between the measured values and the reference values within stated measurement uncertainties. The differences remained within ±1.15% in PMAX and within ±0.35% in VOC for all participants and methods applied. Correlations were observed among the PMAX, VOC, and FF differences from their weighted mean. An analysis of the effects of transient current (dQ/dt) at maximum power point caused by hysteresis effect on the measurement error of PMAX showed a significant linear correlation between error of maximum power and junction voltage sweep rate for heterojunction (HJT) solar cells. This work forms the basis to validate all applied methods and their stated measurement uncertainties.


  • Open Access

    Results from an international interlaboratory study on light‐ and elevated temperature‐induced degradation in solar modules

    by Joseph Karas, Ingrid Repins, Karl A. Berger, Bernhard Kubicek, Fangdan Jiang, Daqi Zhang, Jean‐Nicolas Jaubert, Ana Belén Cueli, Tony Sample, Bengt Jaeckel, et al.

    This paper reports the results of an international interlaboratory comparison study on light‐ and elevated temperature‐induced degradation (LETID) on crystalline silicon photovoltaic (PV) modules. A large global network of PV module manufacturers and PV testing laboratories collaborated to design a protocol for LETID detection and screen a large and diverse set of prototype modules for LETID. Results across labs indicate the reproducibility of LETID testing is likely within ±1% of maximum power (PMP). In intentionally engineered LETID‐sensitive modules, mean degradation after the prescribed detection stress is roughly 6% PMP. In other module types the LETID sensitivity is smaller, and in some we observe essentially negligible degradation attributable to LETID. In LETID‐sensitive modules, both open‐circuit voltage (VOC) and short‐circuit current (ISC) degrade by a roughly similar magnitude. We observe, as do previous studies, that LETID affects each cell in a module differently. An investigation of the potential mismatch losses caused by nonuniform LETID degradation found that mismatch loss is insignificant compared to the estimated loss of cell ISC, which drives loss of module ISC. Overall, this work has helped inform the creation of a forthcoming standard technical specification for LETID testing of PV modules, IEC TS 63342 ED1, and should aid in the interpretation of results from that and other LETID tests.


  • Rear‐side spectral irradiance at 1 sun and application to bifacial module power rating

    by Christos Monokroussos, Qi Gao, XiaoYu Zhang, Eleanor Lee, Yihong Wang, Chris Zou, Lorenz Rimmelspacher, Johanna Bonilla Castro, Markus Schweiger, Werner Herrmann

    The air mass 1.5 global (AM1.5G) reference spectral irradiance distribution is defined in the international standard IEC 60904‐3, accounts for the direct, diffuse, and albedo components directing 1000 W/m2 (1 sun) of global irradiance at a photovoltaic (PV) module's front side. Bifacial PV modules, however, receive an additional irradiance contribution from the rear side, which is not accounted for in the reference irradiance. This work strives to shed light on the amount of expected light that arrives on the rear side of a PV module, when the front‐side irradiance and ambient conditions match the conditions used for the calculation of AM1.5G. For this purpose, an optical model was developed to simulate the rear‐side spectral irradiance of PV modules, whose validity was verified by outdoor measurements. The results show that the average rear‐side irradiance at a set of conditions as defined in IEC 60904‐3 lies in the range of 130 to 150 W/m2. The results of this work lay the foundation to define the bifacial Standard Test Conditions (BSTC), which can be used to support the technical specification IEC TS 60904‐1‐2 and international standard IEC 60904‐3 and establish supplementary requirements for the power rating and label verification of bifacial PV modules.


  • Open Access

    Electrical characterization intercomparison of high‐efficiency c‐Si modules within Asian and European laboratories

    by Christos Monokroussos, Elena Salis, Damien Etienne, XiaoYu Zhang, Sebastian Dittmann, Gabi Friesen, Kengo Morita, Johannes Stang, Thomas Herbrecht, Vahid Fakhfouri, et al.

    This work presents the results of a high‐efficiency (HE) photovoltaic (PV) module round‐robin intercomparison between five Asian and European ISO/IEC 17025 accredited laboratories and one industrial laboratory based in Europe. The scope of the round‐robin was to examine the measurements comparability for this PV technology with respect to ISO/IEC 17025 laboratory conformity assessment and also to examine the accuracy of step‐like methods towards transient errors against already validated methods. The devices under test were four types of HE c‐Si PV modules with efficiencies varying between 16.5% and 19.0%. The results indicate that a satisfactory agreement was achieved with maximum deviations of 1.59% in Pmax, 1.13% in Isc, and 0.64% in Voc for all devices under test. The weighted standard deviations in Pmax per device type, which can be seen as a conservative estimate of interlaboratory agreement for HE c‐Si PV, ranged within 0.82% to 2.23% (k = 2). The accuracy of step‐like methods towards transient errors was evaluated by comparing a second series of results at fixed Isc for each module under test, eliminating the influence of the effective irradiance measurement. This work suggests that the contribution of capacitive errors was in the range (0.47 ± 0.19) % (k = 2). A spectral mismatch sensitivity analysis showed that an accurate measurement of the spectral irradiance and of the involved spectral responsivities together with the punctual correction for the spectral mismatch can reduce the error in the measurement of PV modules performance of about 2% even in the case of c‐Si against c‐Si and class AAA solar simulators.


  • Combined and Sequential Accelerated Stress Testing for Derisking Photovoltaic Modules

    by Peter Hacke, Michael Owen-Bellini, Michel Kempe, David C. Miller, Tadonori Tanahashi, Keiichiro Sakurai, William J. Gambogi, John T. Trout, Thomas C. Felder, Kaushik Roy Choudhury, et al.