Felix Hippauf
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Felix Hippauf has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
- Stefan Kaskel
Technische Universität Dresden
6 shared publications Holger Althues
4 shared publications- Susanne Dörfler
Department Chemical Surface and Battery Technology Fraunhofer Institute for Material and Beam Technology (IWS) Winterbergstraße 28 01277 Dresden Germany
4 shared publications - Holger Althues
Fraunhofer Institute for Material and Beam Technology , Winterbergstraße 28
3 shared publications Thomas Abendroth
Fraunhofer Institute for Material and Beam Technology IWS Winterbergstrasse 28 01277 Dresden Germany
3 shared publications- Thomas Abendroth
Department Chemical Surface and Battery Technology Fraunhofer Institute for Material and Beam Technology (IWS) Winterbergstraße 28 01277 Dresden Germany
3 shared publications
Latest Publications
- Open Access
- 27 October 2026
- Published by Elsevier in SSRN Electronic Journal
Upscaling of iodine-doped Li-S solid-state battery cathode composites via low-energy ball milling
Lithium–sulfur batteries with sulfidic solid-electrolyte (SE) outperform liquid-electrolyte-based systems, offering near-theoretical active-material utilization with improved safety. Their development, however, is particularly hindered by the limited scalability of high-energy ball milling (HBM) and the accompanied chemo-mechanical degradation of the SE. Here, a scalable processing strategy for cathode composite fabrication is introduced. Instead of lengthy one-pot ball-milling, sulfur and iodine are melt-infiltrated into carbons. Subsequently, low-energy ball-milling integrates the argyrodite SE while preserving its crystallinity. Two carbon architectures are compared: an agglomerated carbon black and a mesoporous carbon with well-defined, interconnected pores.Systematic variation of iodine content identifies 19 wt% I₂, replacing a fraction of SE, as optimal. Electrochemical testing, XRD, Raman, and SEM/FIB-SEM correlate microstructure with performance. HBM composites show irreversible SE decomposition and rapid capacity fading, potentially due to formation of I-, S-, and SE- species during milling. By contrast, the thermally treated composites with the S8/I2 mixture confined within the porous carbon, deliver capacities exceeding 1770 mAh gS⁻¹, with 88 % retention after 60 cycles at 25 °C and 20 MPa stack pressure, CE up to 99.9 %, and remarkable rate capability (up to 5C charge/discharge).Adding iodine to sulfur promotes reversible, redox-active interphase formation, enhances interfacial ionic transport, likely through well-distributed in situ-LiI- generation, and improves mechanical integrity via –(P–S–S)ₙ– formation, as corroborated by Raman spectroscopy. Performance is retained upon 100-fold batch-upscaling and at high areal loadings (up to 6.5 mAh cm⁻²), demonstrating great potential for high-capacity, high-rate sulfidic Li-S solid-state batteries, including pouch cells.
- 27 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessUpscaling of iodine-doped Li-S solid-state battery cathode composites via low-energy ball milling
Lithium–sulfur batteries with sulfidic solid-electrolyte (SE) outperform liquid-electrolyte-based systems, offering near-theoretical active-material utilization with improved safety. Their development, however, is particularly hindered by the limited scalability of high-energy ball milling (HBM) and the accompanied chemo-mechanical degradation of the SE. Here, a scalable processing strategy for cathode composite fabrication is introduced. Instead of lengthy one-pot ball-milling, sulfur and iodine are melt-infiltrated into carbons. Subsequently, low-energy ball-milling integrates the argyrodite SE while preserving its crystallinity. Two carbon architectures are compared: an agglomerated carbon black and a mesoporous carbon with well-defined, interconnected pores.Systematic variation of iodine content identifies 19 wt% I₂, replacing a fraction of SE, as optimal. Electrochemical testing, XRD, Raman, and SEM/FIB-SEM correlate microstructure with performance. HBM composites show irreversible SE decomposition and rapid capacity fading, potentially due to formation of I-, S-, and SE- species during milling. By contrast, the thermally treated composites with the S8/I2 mixture confined within the porous carbon, deliver capacities exceeding 1770 mAh gS⁻¹, with 88 % retention after 60 cycles at 25 °C and 20 MPa stack pressure, CE up to 99.9 %, and remarkable rate capability (up to 5C charge/discharge).Adding iodine to sulfur promotes reversible, redox-active interphase formation, enhances interfacial ionic transport, likely through well-distributed in situ-LiI- generation, and improves mechanical integrity via –(P–S–S)ₙ– formation, as corroborated by Raman spectroscopy. Performance is retained upon 100-fold batch-upscaling and at high areal loadings (up to 6.5 mAh cm⁻²), demonstrating great potential for high-capacity, high-rate sulfidic Li-S solid-state batteries, including pouch cells.
- Open Access
- 31 August 2026
- Published by Wiley in Batteries & Supercaps
- Vol. 9 (9) , e70459
Tribochemical Interface Engineering of TiS 4 –Argyrodite Composites for Metal Sulfide‐Based Solid‐State Batteries
Amorphous titanium tetrasulfide (TiS 4 ) is investigated as a high‐capacity cathode material for sulfide‐based solid‐state batteries using Li 6 PS 5 Cl argyrodite as solid electrolyte. A systematic comparison between low‐energy ball milling (LBM) and high‐energy ball milling (HBM) reveals that tribochemical processing intensity determines composite microstructure and electrochemical performance. HBM‐processed composites exhibit superior homogenization confirmed by quantitative FIB‐SEM analysis, achieving discharge capacities of 1110 mAh g S −1 at 0.05 C and 669 mAh g S −1 at 0.5 C. Despite lower bulk electronic conductivity, HBM composites demonstrate enhanced performance consistent with shortened solid‐state diffusion lengths and increased triple‐phase boundary density. SOC‐dependent electrochemical impedance spectroscopy reveals that HBM composites accumulate only 19% impedance growth at 100% SOC over 34 cycles compared to 41% for LBM counterparts, indicating superior interfacial stability. Time‐of‐flight secondary ion mass spectrometry provides spatial evidence for heterogeneous lithiation, with codetected TiS + and Li 3 S + species consistent with gradual structural reorganization along the conversion trajectory. Scalability is demonstrated through dry‐film electrode fabrication, and HBM‐processed cathodes achieve initial capacities of 1240 mAh g S −1 and retain 950 mAh g S −1 after 80 cycles. Absolute capacity values reflect the combined electrochemistry of TiS 4 and partially decomposed Li 6 PS 5 Cl. This work establishes tribochemical processing as a viable strategy for optimizing conversion‐type cathodes in solid‐state batteries.
- 31 August 2026
- Published by Wiley in Batteries & Supercaps
- Vol. 9 (9) , e70459
Open AccessTribochemical Interface Engineering of TiS 4 –Argyrodite Composites for Metal Sulfide‐Based Solid‐State Batteries
Amorphous titanium tetrasulfide (TiS 4 ) is investigated as a high‐capacity cathode material for sulfide‐based solid‐state batteries using Li 6 PS 5 Cl argyrodite as solid electrolyte. A systematic comparison between low‐energy ball milling (LBM) and high‐energy ball milling (HBM) reveals that tribochemical processing intensity determines composite microstructure and electrochemical performance. HBM‐processed composites exhibit superior homogenization confirmed by quantitative FIB‐SEM analysis, achieving discharge capacities of 1110 mAh g S −1 at 0.05 C and 669 mAh g S −1 at 0.5 C. Despite lower bulk electronic conductivity, HBM composites demonstrate enhanced performance consistent with shortened solid‐state diffusion lengths and increased triple‐phase boundary density. SOC‐dependent electrochemical impedance spectroscopy reveals that HBM composites accumulate only 19% impedance growth at 100% SOC over 34 cycles compared to 41% for LBM counterparts, indicating superior interfacial stability. Time‐of‐flight secondary ion mass spectrometry provides spatial evidence for heterogeneous lithiation, with codetected TiS + and Li 3 S + species consistent with gradual structural reorganization along the conversion trajectory. Scalability is demonstrated through dry‐film electrode fabrication, and HBM‐processed cathodes achieve initial capacities of 1240 mAh g S −1 and retain 950 mAh g S −1 after 80 cycles. Absolute capacity values reflect the combined electrochemistry of TiS 4 and partially decomposed Li 6 PS 5 Cl. This work establishes tribochemical processing as a viable strategy for optimizing conversion‐type cathodes in solid‐state batteries.
- Open Access
- 8 October 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (17)
Analysis of the Electrochemical Stability of Sulfide Solid Electrolyte Dry Films for Improved Dry‐Processed Solid‐State Batteries
The solvent‐free processing of cell components is attracting growing interest, as it avoids energy‐intensive drying and solvent recovery procedures. In solid‐state batteries, the dry processing of solid electrolyte (SE) films results in improved ionic conductivities compared to wet processing and eliminates degradation due to residual solvent traces. For dry processing, the binder polytetrafluoroethylene (PTFE) is widely used due to its excellent fibrillation, but it shows poor electrochemical stability at low anode potentials. Here, the influence of processing parameters on the binder structure is evaluated, and the electrochemical degradation of the dry film separators is systematically investigated (e.g., CTTA measurements) at different anode potentials (Si and Li anode). A combination of electrochemical and surface characterization at the SE dry film/anode interface is conducted. The results confirm that processing has a large influence on the stability at the dry film/anode interface. By adapting the SE dry film processing, long‐term cycling in Si||NMC pouch cells is demonstrated over more than 1300 cycles. Additionally, a high initial coulombic efficiency of 92% and an average CE of 99.7% are obtained over 100 cycles, highlighting the potential of dry film separators for the application with Si anodes.
- 8 October 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (17)
Open AccessAnalysis of the Electrochemical Stability of Sulfide Solid Electrolyte Dry Films for Improved Dry‐Processed Solid‐State Batteries
The solvent‐free processing of cell components is attracting growing interest, as it avoids energy‐intensive drying and solvent recovery procedures. In solid‐state batteries, the dry processing of solid electrolyte (SE) films results in improved ionic conductivities compared to wet processing and eliminates degradation due to residual solvent traces. For dry processing, the binder polytetrafluoroethylene (PTFE) is widely used due to its excellent fibrillation, but it shows poor electrochemical stability at low anode potentials. Here, the influence of processing parameters on the binder structure is evaluated, and the electrochemical degradation of the dry film separators is systematically investigated (e.g., CTTA measurements) at different anode potentials (Si and Li anode). A combination of electrochemical and surface characterization at the SE dry film/anode interface is conducted. The results confirm that processing has a large influence on the stability at the dry film/anode interface. By adapting the SE dry film processing, long‐term cycling in Si||NMC pouch cells is demonstrated over more than 1300 cycles. Additionally, a high initial coulombic efficiency of 92% and an average CE of 99.7% are obtained over 100 cycles, highlighting the potential of dry film separators for the application with Si anodes.
- Open Access
- 10 January 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 15 (19)
Toward Higher Energy Density All‐Solid‐State Batteries by Production of Freestanding Thin Solid Sulfidic Electrolyte Membranes in a Roll‐to‐Roll Process
All‐solid‐state batteries (SSB) show great promise for the advancement of high‐energy batteries. To maximize the energy density, a key research interest lies in the development of ultrathin and highly conductive solid electrolyte (SE) layers. In this work, thin and flexible sulfide solid electrolyte membranes are fabricated and laminated onto a non‐woven fabric using a scalable and solvent‐free, continuous roll‐to‐roll process (DRYtraec). These membranes show significantly improved tensile strength compared to unsupported sheets, which facilitates cell assembly and allows a continuous component production using a single‐step calendering process. By tuning the thickness, densified membranes with thicknesses ranging from 40 to 160 µm are obtained after a compression step. The resulting SE membranes retain a high ionic conductivity (1.6 mS cm−1) at room temperature. An excellent rate capability is demonstrated in a SSB pouch cell with a Li2O–ZrO2‐coated LiNi0.9C0.05Mn0.05O2 cathode, a 55 µm thin SE membrane, and a columnar silicon anode fabricated by a scalable physical vapor deposition process. At stack level, a promising energy density of 673 Wh L−1 (and specific energy of 247 Wh kg−1) is achieved, showcasing the potential for high energy densities by reducing the SE membrane thickness while retaining good mechanical properties.
- 10 January 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 15 (19)
Open AccessToward Higher Energy Density All‐Solid‐State Batteries by Production of Freestanding Thin Solid Sulfidic Electrolyte Membranes in a Roll‐to‐Roll Process
All‐solid‐state batteries (SSB) show great promise for the advancement of high‐energy batteries. To maximize the energy density, a key research interest lies in the development of ultrathin and highly conductive solid electrolyte (SE) layers. In this work, thin and flexible sulfide solid electrolyte membranes are fabricated and laminated onto a non‐woven fabric using a scalable and solvent‐free, continuous roll‐to‐roll process (DRYtraec). These membranes show significantly improved tensile strength compared to unsupported sheets, which facilitates cell assembly and allows a continuous component production using a single‐step calendering process. By tuning the thickness, densified membranes with thicknesses ranging from 40 to 160 µm are obtained after a compression step. The resulting SE membranes retain a high ionic conductivity (1.6 mS cm−1) at room temperature. An excellent rate capability is demonstrated in a SSB pouch cell with a Li2O–ZrO2‐coated LiNi0.9C0.05Mn0.05O2 cathode, a 55 µm thin SE membrane, and a columnar silicon anode fabricated by a scalable physical vapor deposition process. At stack level, a promising energy density of 673 Wh L−1 (and specific energy of 247 Wh kg−1) is achieved, showcasing the potential for high energy densities by reducing the SE membrane thickness while retaining good mechanical properties.
- Top Cited PapersOpen Access
- 18 September 2024
- Published by Springer Nature in Nature Energy
- Vol. 9 (10) , 1310-1320
Benchmarking the reproducibility of all-solid-state battery cell performance
The interlaboratory comparability and reproducibility of all-solid-state battery cell cycling performance are poorly understood due to the lack of standardized set-ups and assembly parameters. This study quantifies the extent of this variability by providing commercially sourced battery materials—LiNi0.6Mn0.2Co0.2O2 for the positive electrode, Li6PS5Cl as the solid electrolyte and indium for the negative electrode—to 21 research groups. Each group was asked to use their own cell assembly protocol but follow a specific electrochemical protocol. The results show large variability in assembly and electrochemical performance, including differences in processing pressures, pressing durations and In-to-Li ratios. Despite this, an initial open circuit voltage of 2.5 and 2.7 V vs Li+/Li is a good predictor of successful cycling for cells using these electroactive materials. We suggest a set of parameters for reporting all-solid-state battery cycling results and advocate for reporting data in triplicate.
- 18 September 2024
- Published by Springer Nature in Nature Energy
- Vol. 9 (10) , 1310-1320
Top Cited PapersOpen AccessBenchmarking the reproducibility of all-solid-state battery cell performance
The interlaboratory comparability and reproducibility of all-solid-state battery cell cycling performance are poorly understood due to the lack of standardized set-ups and assembly parameters. This study quantifies the extent of this variability by providing commercially sourced battery materials—LiNi0.6Mn0.2Co0.2O2 for the positive electrode, Li6PS5Cl as the solid electrolyte and indium for the negative electrode—to 21 research groups. Each group was asked to use their own cell assembly protocol but follow a specific electrochemical protocol. The results show large variability in assembly and electrochemical performance, including differences in processing pressures, pressing durations and In-to-Li ratios. Despite this, an initial open circuit voltage of 2.5 and 2.7 V vs Li+/Li is a good predictor of successful cycling for cells using these electroactive materials. We suggest a set of parameters for reporting all-solid-state battery cycling results and advocate for reporting data in triplicate.
- Open Access
- 5 August 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (43)
A Small Electrolyte Drop Enables a Disruptive Semisolid High‐Energy Sulfur Battery Cell Design via an Argyrodite‐Based Sulfur Cathode in Combination with a Metallic Lithium Anode
Lithium–sulfur batteries with liquid electrolytes are discussed as the most promising post‐lithium‐ion‐battery technology in literature due to their high theoretical specific energy and first prototype cells delivering >470 Wh kg−1. Although several electrolyte and material concepts are developed that partially solve the issue of the so‐called shuttle mechanism, the most promising concept to genuinely confine sulfur species in the cathode is all‐solid‐state argyrodite–sulfur cathodes leading to almost theoretical active material utilization by maintaining reasonable sulfur loadings and electrolyte to sulfur ratios. However, this battery concept has so far not achieved reversible cycling against metallic lithium anodes as it requires high pressures for manufacturing, and ductile lithium metal creeps along the grain boundaries of the solid electrolyte particles leading to short cuts of the cells. Recent findings show that metallic lithium, however, can be stably cycled with dimethoxyethane/lithium‐bis(fluorosulfonyl)imide (DME/LiFSI)‐based electrolytes. Herein, for the first time, a semisolid concept is presented combining the benefits of an argyrodite‐based solid‐state cathode and a DME/LiFSI/hydrofluoroether‐based anolyte concept – in coin cells and first pouch cells. This disruptive approach enables projected specific energies higher than 600 Wh kg−1 at cell stack level.
- 5 August 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (43)
Open AccessA Small Electrolyte Drop Enables a Disruptive Semisolid High‐Energy Sulfur Battery Cell Design via an Argyrodite‐Based Sulfur Cathode in Combination with a Metallic Lithium Anode
Lithium–sulfur batteries with liquid electrolytes are discussed as the most promising post‐lithium‐ion‐battery technology in literature due to their high theoretical specific energy and first prototype cells delivering >470 Wh kg−1. Although several electrolyte and material concepts are developed that partially solve the issue of the so‐called shuttle mechanism, the most promising concept to genuinely confine sulfur species in the cathode is all‐solid‐state argyrodite–sulfur cathodes leading to almost theoretical active material utilization by maintaining reasonable sulfur loadings and electrolyte to sulfur ratios. However, this battery concept has so far not achieved reversible cycling against metallic lithium anodes as it requires high pressures for manufacturing, and ductile lithium metal creeps along the grain boundaries of the solid electrolyte particles leading to short cuts of the cells. Recent findings show that metallic lithium, however, can be stably cycled with dimethoxyethane/lithium‐bis(fluorosulfonyl)imide (DME/LiFSI)‐based electrolytes. Herein, for the first time, a semisolid concept is presented combining the benefits of an argyrodite‐based solid‐state cathode and a DME/LiFSI/hydrofluoroether‐based anolyte concept – in coin cells and first pouch cells. This disruptive approach enables projected specific energies higher than 600 Wh kg−1 at cell stack level.
- Open Access
- 3 February 2023
- Published by Wiley in Advanced Sustainable Systems
- Vol. 7 (4)
Mechanistic Insights into the Cycling Behavior of Sulfur Dry‐Film Cathodes
All‐solid‐state lithium–sulfur batteries (ASSB‐LiS batteries) are considered among advanced candidates for next‐generation energy storage systems, as they break with restrictions and limitations that liquid electrolytes impose on lithium‐ion batteries and lithium‐sulfur batteries (LiS‐batteries), meaning enhanced safety and higher energy densities. However, investigations under realistic conditions on pouch cell level are challenging, as it is necessary to implement a scalable preparation method for sheet‐type cathodes with high sulfur utilization and loading. In this study, a solvent‐free process to prepare free‐standing cathode sheets with low binder content down to 0.1 wt% PTFE is demonstrated. The contribution of binder and electrolyte on the conversion reaction of sulfur is discussed. Sheet‐type cathodes reach nearly theoretical sulfur utilization of 1672 mAh gS−1 and outstanding reversible capacity retention with 72% of initial discharge capacity after 400 cycles by adapting cut‐off voltages to the stability window of the electrolyte. Furthermore, an all‐solid‐state pouch cell is demonstrated using the dry‐film cathode, which is successfully tested for 50 cycles at different C‐rates. Thickness monitoring of the cell stack gives fundamental insights into the volume change and breathing behavior of both cathode and anode.
- 3 February 2023
- Published by Wiley in Advanced Sustainable Systems
- Vol. 7 (4)
Open AccessMechanistic Insights into the Cycling Behavior of Sulfur Dry‐Film Cathodes
All‐solid‐state lithium–sulfur batteries (ASSB‐LiS batteries) are considered among advanced candidates for next‐generation energy storage systems, as they break with restrictions and limitations that liquid electrolytes impose on lithium‐ion batteries and lithium‐sulfur batteries (LiS‐batteries), meaning enhanced safety and higher energy densities. However, investigations under realistic conditions on pouch cell level are challenging, as it is necessary to implement a scalable preparation method for sheet‐type cathodes with high sulfur utilization and loading. In this study, a solvent‐free process to prepare free‐standing cathode sheets with low binder content down to 0.1 wt% PTFE is demonstrated. The contribution of binder and electrolyte on the conversion reaction of sulfur is discussed. Sheet‐type cathodes reach nearly theoretical sulfur utilization of 1672 mAh gS−1 and outstanding reversible capacity retention with 72% of initial discharge capacity after 400 cycles by adapting cut‐off voltages to the stability window of the electrolyte. Furthermore, an all‐solid‐state pouch cell is demonstrated using the dry‐film cathode, which is successfully tested for 50 cycles at different C‐rates. Thickness monitoring of the cell stack gives fundamental insights into the volume change and breathing behavior of both cathode and anode.
- Open Access
- 22 May 2021
- Published by Wiley in Energy Technology
- Vol. 9 (8) , 2100145
Increasing the Stability of LiMn2O4 Against Harsh Conditions During Lithium Recovery from Real Brine Solutions
Brines are abundant waste products from desalination plants and have higher lithium contents than sea water (0.17 ppm). Herein, electrochemical lithium recovery from real brine solutions using Li‐selective LiMn2O4 is reported. Free‐standing electrodes are prepared completely solvent‐free. At low current densities, the complete theoretical capacity of 148 mAh g−1 can be utilized. The process is highly rate dependent due to the lithium concentration in the mm range. The high salt content of the brine depicts a challenging environment for electrodes and reactor materials. Competing earth‐alkali metals lead to scale formation blocking the electrode surface and reducing the electrode capacity for lithium uptake. The high chloride concentration enables the formation of chlorine Cl2 at potentials < 1 V versus Ag/AgCl competing with the deintercalation of lithium. A combination of commercial antiscalants was used to suppress the formation of CaCO3 at the electrode prolonging its cycle life. It is shown that a cation exchange membrane not only effectively blocks chloride ions from the electrode but also decreases the Li‐diffusion. Finally, the selectivity of the process is proven in a real brine with a low lithium content (0.7 mm), and an actual recovery experiment is conducted in a flow setup.
- 22 May 2021
- Published by Wiley in Energy Technology
- Vol. 9 (8) , 2100145
Open AccessIncreasing the Stability of LiMn2O4 Against Harsh Conditions During Lithium Recovery from Real Brine Solutions
Brines are abundant waste products from desalination plants and have higher lithium contents than sea water (0.17 ppm). Herein, electrochemical lithium recovery from real brine solutions using Li‐selective LiMn2O4 is reported. Free‐standing electrodes are prepared completely solvent‐free. At low current densities, the complete theoretical capacity of 148 mAh g−1 can be utilized. The process is highly rate dependent due to the lithium concentration in the mm range. The high salt content of the brine depicts a challenging environment for electrodes and reactor materials. Competing earth‐alkali metals lead to scale formation blocking the electrode surface and reducing the electrode capacity for lithium uptake. The high chloride concentration enables the formation of chlorine Cl2 at potentials < 1 V versus Ag/AgCl competing with the deintercalation of lithium. A combination of commercial antiscalants was used to suppress the formation of CaCO3 at the electrode prolonging its cycle life. It is shown that a cation exchange membrane not only effectively blocks chloride ions from the electrode but also decreases the Li‐diffusion. Finally, the selectivity of the process is proven in a real brine with a low lithium content (0.7 mm), and an actual recovery experiment is conducted in a flow setup.