Snorre Aunet
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Snorre Aunet has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Trond Ytterdal
Norwegian University of Science and Technology
4 shared publications - Even Late
Department of Electronics and Telecommunications, Norges teknisk-naturvitenskapelige universitet, 7030 Trondheim, Norway
2 shared publications - Ali Asghar Vatanjou
Department of Electronic Systems (IES), Norwegian University of Science and Technology (NTNU), 7491 Trondheim, Norway
1 shared publication - Alireza Saberkari
Department of Electrical Engineering, Linkping University, Linkping, Sweden
1 shared publication - Azam Seyedi
Department of Electronic Systems, Faculty of Information Technology and Electrical Engineering, Norwegian University of Science and Technology (NTNU), Trondheim, Norway
1 shared publication - Dag T. Wisland
University of Oslo
1 shared publication
Latest Publications
- 13 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (8) , 11551-11563
Self-Oscillating Joule Thief Converters for MEMS Electromagnetic Energy Harvesting: Analytical Modeling and Experimental Validation
MEMS electromagnetic energy harvesters face a critical cold-start bottleneck: ultralow voltage combined with high source impedance. Existing startup converters optimize for either low voltage or high impedance, rarely both. This article addresses this challenge by adapting the self-oscillating joule thief topology through closed-form analytical modeling. Unlike prior semianalytical approaches requiring iterative simulation, our framework enables simulation-free design exploration of bipolar junction transistor (BJT)- and N-type metal-oxide-semiconductor (NMOS)-based implementations. For both implementations, the analytical model predicts output voltage within 10% of experimental results over the measured voltage, load, and source-resistance sweeps. The NMOS version demonstrates a 50 mV start-up from a 300 $\boldsymbol{\Omega}$ source impedance. Experimental validation with a 300 $\boldsymbol{\Omega}$ electromagnetic energy harvester shows a tradeoff in practice: zero-threshold NMOS starts at 0.35 g rms acceleration but provides 43% boost; low-threshold NMOS starts at 0.5 g but achieves 93% boost—both outperforming TI BQ25570’s 0.7 g startup requirement. By positioning the joule thief as a specialized startup circuit complementing high-efficiency main converters, this framework addresses a key barrier to self-powered MEMS deployment and high-impedance source energy harvesting.
- 13 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (8) , 11551-11563
Self-Oscillating Joule Thief Converters for MEMS Electromagnetic Energy Harvesting: Analytical Modeling and Experimental Validation
MEMS electromagnetic energy harvesters face a critical cold-start bottleneck: ultralow voltage combined with high source impedance. Existing startup converters optimize for either low voltage or high impedance, rarely both. This article addresses this challenge by adapting the self-oscillating joule thief topology through closed-form analytical modeling. Unlike prior semianalytical approaches requiring iterative simulation, our framework enables simulation-free design exploration of bipolar junction transistor (BJT)- and N-type metal-oxide-semiconductor (NMOS)-based implementations. For both implementations, the analytical model predicts output voltage within 10% of experimental results over the measured voltage, load, and source-resistance sweeps. The NMOS version demonstrates a 50 mV start-up from a 300 $\boldsymbol{\Omega}$ source impedance. Experimental validation with a 300 $\boldsymbol{\Omega}$ electromagnetic energy harvester shows a tradeoff in practice: zero-threshold NMOS starts at 0.35 g rms acceleration but provides 43% boost; low-threshold NMOS starts at 0.5 g but achieves 93% boost—both outperforming TI BQ25570’s 0.7 g startup requirement. By positioning the joule thief as a specialized startup circuit complementing high-efficiency main converters, this framework addresses a key barrier to self-powered MEMS deployment and high-impedance source energy harvesting.
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 141896-141907
A Low-Power, Ultra-Low-Voltage Custom Topology CMOS Inverter Applicable Across All Regions of Operation
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 141896-141907
Open AccessA Low-Power, Ultra-Low-Voltage Custom Topology CMOS Inverter Applicable Across All Regions of Operation
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- p. 1
A Sub-70 mV SRAM based on DTMOS Schmitt-Trigger Circuits in 130 nm SOI CMOS for Self-Powered IoT
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- p. 1
Open AccessA Sub-70 mV SRAM based on DTMOS Schmitt-Trigger Circuits in 130 nm SOI CMOS for Self-Powered IoT
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 32 (12) , 2169-2172
Guest Editorial Selected Papers From IEEE Nordic Circuits and Systems Conference (NorCAS) 2023
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 32 (12) , 2169-2172
Guest Editorial Selected Papers From IEEE Nordic Circuits and Systems Conference (NorCAS) 2023
- Open Access
- 8 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 30624-30642
Nwise and Pwise: 10T Radiation Hardened SRAM Cells for Space Applications With High Reliability Requirements
SRAM cells are widely used to design memory blocks of, e.g., caches, register files, and translation lookaside buffers. Depending on the SRAM application, the design requirements are different. For instance, in space applications, alongside energy efficiency, reliability is a main issue since the system is launched into space with a limited energy budget and stays exposed to high doses of radiation strikes for a long time. The Nwise cell has recently been proposed by the authors of this paper as the first highly reliable radiation hardened SRAM cell designed with 28nm FD-SOI. In this paper, inspired from the Nwise cell, we introduce another highly reliable radiation hardened SRAM cell, the Pwise cell, which is also designed with 28nm FD-SOI technology. Through comprehensive simulations of state-of-the-art cells, we show that both the Nwise and Pwise cells are competitive radiation hardened SRAMs to use in different memory blocks for space applications: 1) Both have the highest level of Single Event Upsets (SEU) tolerance capability for the temperature range deployed in space applications; further, both have the highest level of the tolerance capability to Multi Event Upsets (MEU). 2) Compared with the simulated cells that have comparable tolerance capability, the Nwise cell has low read delay and read power consumption, hence, it can be a good choice for space application cache designs, while the Pwise cell can be a proper candidate for space application register file designs since it has low write and read delay.
- 8 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 30624-30642
Open AccessNwise and Pwise: 10T Radiation Hardened SRAM Cells for Space Applications With High Reliability Requirements
SRAM cells are widely used to design memory blocks of, e.g., caches, register files, and translation lookaside buffers. Depending on the SRAM application, the design requirements are different. For instance, in space applications, alongside energy efficiency, reliability is a main issue since the system is launched into space with a limited energy budget and stays exposed to high doses of radiation strikes for a long time. The Nwise cell has recently been proposed by the authors of this paper as the first highly reliable radiation hardened SRAM cell designed with 28nm FD-SOI. In this paper, inspired from the Nwise cell, we introduce another highly reliable radiation hardened SRAM cell, the Pwise cell, which is also designed with 28nm FD-SOI technology. Through comprehensive simulations of state-of-the-art cells, we show that both the Nwise and Pwise cells are competitive radiation hardened SRAMs to use in different memory blocks for space applications: 1) Both have the highest level of Single Event Upsets (SEU) tolerance capability for the temperature range deployed in space applications; further, both have the highest level of the tolerance capability to Multi Event Upsets (MEU). 2) Compared with the simulated cells that have comparable tolerance capability, the Nwise cell has low read delay and read power consumption, hence, it can be a good choice for space application cache designs, while the Pwise cell can be a proper candidate for space application register file designs since it has low write and read delay.
- 14 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 28 (10) , 2223-2227
Benefiting From State Dependencies in Asymmetric SRAM Cells Through Conditional Word-Flipping
This brief presents an approach that dynamically exploits content dependencies in asymmetric memory cells. By using a capacitive, logic-value majority circuit and an extra column of memory cells, words are conditionally flipped during write operations to reach the more beneficial state for storage. A 1-kb SRAM block of low-voltage memory cells was implemented and manufactured in a 130-nm CMOS. The memory cells were made writable and read-stable at low supply voltages with a single-ended write and single-ended read structure using six multithreshold transistors that give rise to an asymmetric retention power. At a supply voltage of 350 mV, the content-dependent leakage power in the asymmetric memory cell is 23 times smaller when storing logic ``1''s compared with logic ``0''s. A derived statistical model suggests that the mean, wordwise, static power savings of the word-flipping scheme become 15.70% for 8-bit words of uniform bit probability. For the implemented SRAM macro, the mean improvement for the retention power is, including flip logic and decoder and driver overheads, found to be 14.69%. In boundary tests, by writing all words full of undesired values, the power saving becomes 80.37%, while writing all words full of desired values causes a power penalty of 6.14%. Measurement results confirm the improvement in retention power with a ten-chip mean improvement of 11.93% for the same data set.
- 14 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 28 (10) , 2223-2227
Benefiting From State Dependencies in Asymmetric SRAM Cells Through Conditional Word-Flipping
This brief presents an approach that dynamically exploits content dependencies in asymmetric memory cells. By using a capacitive, logic-value majority circuit and an extra column of memory cells, words are conditionally flipped during write operations to reach the more beneficial state for storage. A 1-kb SRAM block of low-voltage memory cells was implemented and manufactured in a 130-nm CMOS. The memory cells were made writable and read-stable at low supply voltages with a single-ended write and single-ended read structure using six multithreshold transistors that give rise to an asymmetric retention power. At a supply voltage of 350 mV, the content-dependent leakage power in the asymmetric memory cell is 23 times smaller when storing logic ``1''s compared with logic ``0''s. A derived statistical model suggests that the mean, wordwise, static power savings of the word-flipping scheme become 15.70% for 8-bit words of uniform bit probability. For the implemented SRAM macro, the mean improvement for the retention power is, including flip logic and decoder and driver overheads, found to be 14.69%. In boundary tests, by writing all words full of undesired values, the power saving becomes 80.37%, while writing all words full of desired values causes a power penalty of 6.14%. Measurement results confirm the improvement in retention power with a ten-chip mean improvement of 11.93% for the same data set.
- 14 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (11) , 2687-2691
An Energy Efficient Level Shifter Capable of Logic Conversion From Sub-15 mV to 1.2 V
- 14 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (11) , 2687-2691
An Energy Efficient Level Shifter Capable of Logic Conversion From Sub-15 mV to 1.2 V
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Exploring optimal back bias voltages for ultra low voltage CMOS digital Circuits in 22 nm FDSOI Technology
This study presents a strategy to determine optimal body bias voltages for ultra low voltage digital circuits in the 22 nm Fully Depleted Silicon On Insulator Technology (FDSOI). The efficiency of body biasing for achieving high functional yield has been investigated by using reverse back bias voltages for HVT devices. The strategy has been evaluated through the design of an ultra low voltage Xor based adder at supply voltages varying from 140–160 mV and temperature range 27–50 °C at 1 kHz frequency. The adder under optimal body bias consumes 4.67 percent less energy than zero body bias at Vdd=150mV and frequency of 1 kHz. The adder is fully functional for one thousand Monte Carlo simulations at optimal back bias voltage. The yield has improved by 0.4 percent in optimal back bias voltage compared to zero body bias. The results show the lowest Energy per cycle, variability and high functional yield for the obtained optimal body bias voltage. Also, additional analysis confirms the dependency of optimal body bias voltage on the switching activity and operating conditions for a given technology. We also show that the relative energy variability is larger than the delay variability over the back bias voltage range.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Exploring optimal back bias voltages for ultra low voltage CMOS digital Circuits in 22 nm FDSOI Technology
This study presents a strategy to determine optimal body bias voltages for ultra low voltage digital circuits in the 22 nm Fully Depleted Silicon On Insulator Technology (FDSOI). The efficiency of body biasing for achieving high functional yield has been investigated by using reverse back bias voltages for HVT devices. The strategy has been evaluated through the design of an ultra low voltage Xor based adder at supply voltages varying from 140–160 mV and temperature range 27–50 °C at 1 kHz frequency. The adder under optimal body bias consumes 4.67 percent less energy than zero body bias at Vdd=150mV and frequency of 1 kHz. The adder is fully functional for one thousand Monte Carlo simulations at optimal back bias voltage. The yield has improved by 0.4 percent in optimal back bias voltage compared to zero body bias. The results show the lowest Energy per cycle, variability and high functional yield for the obtained optimal body bias voltage. Also, additional analysis confirms the dependency of optimal body bias voltage on the switching activity and operating conditions for a given technology. We also show that the relative energy variability is larger than the delay variability over the back bias voltage range.
- 24 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 66 (6) , 899-903
An Ultra-Low Voltage and Low-Energy Level Shifter in 28-nm UTBB-FDSOI
A low-power level shifter capable of up-converting sub-50 mV input voltages to 1 V has been implemented in a 28 nm FDSOI technology. Diode connected transistors and a single-NWELL layout strategy have been used along with poly and back-gate biasing techniques to achieve an adequate balance between the drive strength of the pull-up and the pull-down networks. Measurements showed that the lowest input voltage levels, which could be upconverted by the 10 chip samples, varied from 39 mV to 52 mV. Half of the samples could upconvert from 39 mV to 1 V. The simulated energy consumption of the level shifter was 5.2 fJ for an up-conversion from 0.2 V to 1 V and 1 MHz operating frequency.
- 24 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 66 (6) , 899-903
An Ultra-Low Voltage and Low-Energy Level Shifter in 28-nm UTBB-FDSOI
A low-power level shifter capable of up-converting sub-50 mV input voltages to 1 V has been implemented in a 28 nm FDSOI technology. Diode connected transistors and a single-NWELL layout strategy have been used along with poly and back-gate biasing techniques to achieve an adequate balance between the drive strength of the pull-up and the pull-down networks. Measurements showed that the lowest input voltage levels, which could be upconverted by the 10 chip samples, varied from 39 mV to 52 mV. Half of the samples could upconvert from 39 mV to 1 V. The simulated energy consumption of the level shifter was 5.2 fJ for an up-conversion from 0.2 V to 1 V and 1 MHz operating frequency.