Matěj Lédl
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Matěj Lédl has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Lenka Nevřivová
Brno University of Technology
3 shared publications Nikol Žižková
Brno University of Technology
3 shared publications- Rostislav Drochytka
Faculty of Civil Engineering, Institute of Technology of Building Materials and Components, Brno University of Technology, Brno, Czech Republic
3 shared publications Lucie Galvánková
Brno University of Technology
2 shared publications- Denisa Beranová
Brno University of Technology
1 shared publication Jakub Tkacz
Brno University of Technology
1 shared publication
Latest Publications
- Open Access
- 1 January 2019
- Published by Wiley in Advances in Civil Engineering
- Vol. 2019 (1)
Use of Secondary Crystallization and Fly Ash in Waterproofing Materials to Increase Concrete Resistance to Aggressive Gases and Liquids
This paper describes the use of cement‐based waterproofing screed and waterproofing coating, in which 10% of the original amount of cement was replaced by fly ash and 2% of the crystallization admixture was added by weight of cement, as a mean of protection of concrete against aggressive environments. The modified materials were applied to the underlying concrete and subjected to testing of physical and mechanical properties after exposure to effects of aggressive environments for up to 18 months. The results of the analysis have shown that after the application of waterproofing materials, there is a sufficient development of the crystals in the underlying concrete to enhance its durability. Thus, it is possible to use fly ash functionally and efficiently in polymer cement systems as a substitute for the cement together with the crystallization admixture.
- 1 January 2019
- Published by Wiley in Advances in Civil Engineering
- Vol. 2019 (1)
Open AccessUse of Secondary Crystallization and Fly Ash in Waterproofing Materials to Increase Concrete Resistance to Aggressive Gases and Liquids
This paper describes the use of cement‐based waterproofing screed and waterproofing coating, in which 10% of the original amount of cement was replaced by fly ash and 2% of the crystallization admixture was added by weight of cement, as a mean of protection of concrete against aggressive environments. The modified materials were applied to the underlying concrete and subjected to testing of physical and mechanical properties after exposure to effects of aggressive environments for up to 18 months. The results of the analysis have shown that after the application of waterproofing materials, there is a sufficient development of the crystals in the underlying concrete to enhance its durability. Thus, it is possible to use fly ash functionally and efficiently in polymer cement systems as a substitute for the cement together with the crystallization admixture.
- 23 August 2018
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 776, 70-75
Use of Computed Tomography for the Evaluation of Autoclaved Aerated Concrete Structure
This paper deals with the use of computed tomography (CT) images and analytical software for the nondestructive evaluation of the texture of autoclaved aerated concrete (AAC) with 20% fluidized bed combustion fly ash as a substitute for quartz sand. The samples of AAC, made in the laboratory with the same composition but different ways of curing in the fresh stage (before autoclaving), were subjected to observation of the differences in the texture of the silicate matrix, such as inhomogenity, defects, and pore size distribution. The curing conditions with limited drying resulted in formation of larger, locally-connected pores and additional cracking after autoclaving, which led to a decrease in compressive strength up to 1.32 MPa, compared to samples cured in conditions that allowed complete drying reaching 1.95-1.96 MPa. Also there were problems identified related to imperfect laboratory preparation of the samples, such as agglomeration of individual mixture compounds and larger air void formation, due to the absence of vibrating, cracking and weak spots formation. CT provided sufficient contrasting images for consequent software evaluation of pore size distribution, however a higher resolution of the images is needed for determination of pores smaller than 0,125 mm.
- 23 August 2018
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 776, 70-75
Use of Computed Tomography for the Evaluation of Autoclaved Aerated Concrete Structure
This paper deals with the use of computed tomography (CT) images and analytical software for the nondestructive evaluation of the texture of autoclaved aerated concrete (AAC) with 20% fluidized bed combustion fly ash as a substitute for quartz sand. The samples of AAC, made in the laboratory with the same composition but different ways of curing in the fresh stage (before autoclaving), were subjected to observation of the differences in the texture of the silicate matrix, such as inhomogenity, defects, and pore size distribution. The curing conditions with limited drying resulted in formation of larger, locally-connected pores and additional cracking after autoclaving, which led to a decrease in compressive strength up to 1.32 MPa, compared to samples cured in conditions that allowed complete drying reaching 1.95-1.96 MPa. Also there were problems identified related to imperfect laboratory preparation of the samples, such as agglomeration of individual mixture compounds and larger air void formation, due to the absence of vibrating, cracking and weak spots formation. CT provided sufficient contrasting images for consequent software evaluation of pore size distribution, however a higher resolution of the images is needed for determination of pores smaller than 0,125 mm.
- Open Access
- 16 July 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 385 (1) , 012066
Mortars with crystalline additive in aggressive environments
The paper describes how a crystalline additive influences the properties of cement- based composites. The investigation was focused on the degradation of mortars with crystalline additive exposed to selected aggressive environments. The specimens were tested for compressive and flexural strength. The influence on the microstructure is also discussed (high pressure mercury intrusion porosimetry, SEM, DTA). The results confirmed the positive influence of a crystalline additive on the values of compressive strength after exposure to all aggressive environments.
- 16 July 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 385 (1) , 012066
Open AccessMortars with crystalline additive in aggressive environments
The paper describes how a crystalline additive influences the properties of cement- based composites. The investigation was focused on the degradation of mortars with crystalline additive exposed to selected aggressive environments. The specimens were tested for compressive and flexural strength. The influence on the microstructure is also discussed (high pressure mercury intrusion porosimetry, SEM, DTA). The results confirmed the positive influence of a crystalline additive on the values of compressive strength after exposure to all aggressive environments.
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 167-172
Influence of Ammonia Content in SNCR Fly Ash on Phase Composition and Morphology of Autoclaved Aerated Concrete (AAC)
In production of AAC the fly ash was used as a source of SiO2 for many years. Now, after introducing a selective non-catalytic reduction (SNCR) technology to coal combustion process, the fly ash contain ammonia in a form of soluble salts, such as NH4HSO4 and (NH4)2SO4, which causes problems during manufacturing the AAC. Among all the influence of ammonia ions to the phase composition of the final product was not fully described. The main aim of this contribution is to describe the influence of ammonia to phase composition and morphology of autoclaved aerated concrete (AAC). For preparing AAC in laboratory conditions, the fly ash with various content of ammonia was used. The amount of ammonia before and after the hydrothermal reaction was measured by VIS spectrofotometry. The phase composition of prepared samples was determined by means of X-ray diffractometry and confirmed by TG-DTA analysis. The influence of the ammonia to the morphology of final products was studied by scanning electron microscopy.
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 167-172
Influence of Ammonia Content in SNCR Fly Ash on Phase Composition and Morphology of Autoclaved Aerated Concrete (AAC)
In production of AAC the fly ash was used as a source of SiO2 for many years. Now, after introducing a selective non-catalytic reduction (SNCR) technology to coal combustion process, the fly ash contain ammonia in a form of soluble salts, such as NH4HSO4 and (NH4)2SO4, which causes problems during manufacturing the AAC. Among all the influence of ammonia ions to the phase composition of the final product was not fully described. The main aim of this contribution is to describe the influence of ammonia to phase composition and morphology of autoclaved aerated concrete (AAC). For preparing AAC in laboratory conditions, the fly ash with various content of ammonia was used. The amount of ammonia before and after the hydrothermal reaction was measured by VIS spectrofotometry. The phase composition of prepared samples was determined by means of X-ray diffractometry and confirmed by TG-DTA analysis. The influence of the ammonia to the morphology of final products was studied by scanning electron microscopy.
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 148-153
Effect of Ammonium Ion Content in Fly Ash after Selective Non-Catalytic Reduction (SNCR) on Physical and Mechanical Properties of Autoclaved Aerated Concrete (AAC)
After introducing SNCR in coal combustion process in power plants, the valuable by-product such as fly ash remains contaminated with amount of ammonia in form of NH4HSO4, (NH4)2SO4 respectively, which became undesirable in AAC technology because the toxic ammonia is released in the air during the mixing process. This paper deals with the effect of varying ammonia content in fly ash after selective non-catalytic reduction (SNCR) on the physical-mechanical properties of the fly ash based autoclaved aerated concrete (AAC) with the main focus on determination of the impact of the various content of ammonium ion in fly ash on the initial consistency of fresh slurry, the residual content of ammonium ion in hardened aerated matrix and also the impact on the bulk density, compressive strength and tobermorite formation after hydrothermal treatment. Seven batches of AAC, made out of fly ash with rising content of ammonium ion from 0 ppm to 250 ppm, were tested and based on the results obtained it was found out that ammonia is released during the mixing process entirely and doesn‘t remain in AAC after autoclaving, moreover it doesn‘t affect the properties of both fresh slurry (no apparent foaming effect noticed) and thermally treated samples of AAC. Formation of tobermorite wasn’t negatively affected.
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 148-153
Effect of Ammonium Ion Content in Fly Ash after Selective Non-Catalytic Reduction (SNCR) on Physical and Mechanical Properties of Autoclaved Aerated Concrete (AAC)
After introducing SNCR in coal combustion process in power plants, the valuable by-product such as fly ash remains contaminated with amount of ammonia in form of NH4HSO4, (NH4)2SO4 respectively, which became undesirable in AAC technology because the toxic ammonia is released in the air during the mixing process. This paper deals with the effect of varying ammonia content in fly ash after selective non-catalytic reduction (SNCR) on the physical-mechanical properties of the fly ash based autoclaved aerated concrete (AAC) with the main focus on determination of the impact of the various content of ammonium ion in fly ash on the initial consistency of fresh slurry, the residual content of ammonium ion in hardened aerated matrix and also the impact on the bulk density, compressive strength and tobermorite formation after hydrothermal treatment. Seven batches of AAC, made out of fly ash with rising content of ammonium ion from 0 ppm to 250 ppm, were tested and based on the results obtained it was found out that ammonia is released during the mixing process entirely and doesn‘t remain in AAC after autoclaving, moreover it doesn‘t affect the properties of both fresh slurry (no apparent foaming effect noticed) and thermally treated samples of AAC. Formation of tobermorite wasn’t negatively affected.
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 53-59
Effect of Humidity on the Properties of Cement Mortars with a Crystalline Additive
The paper focuses on examining the properties of mortars in which secondary crystallization (crystalline additive) was used. Laboratory tests have found that the effect of secondary crystallization is influenced by conditions in which specimens have been stored during the first 28 days. The investigation focused on the physical-mechanical properties and microstructure of mortar specimens containing a crystalline additive and polypropylene fibres stored at different levels of humidity for 28 days. The influence of crystalline additive on strength was studied as well and the results show that crystalline additives improves the 28-day strength of the mortars.
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 53-59
Effect of Humidity on the Properties of Cement Mortars with a Crystalline Additive
The paper focuses on examining the properties of mortars in which secondary crystallization (crystalline additive) was used. Laboratory tests have found that the effect of secondary crystallization is influenced by conditions in which specimens have been stored during the first 28 days. The investigation focused on the physical-mechanical properties and microstructure of mortar specimens containing a crystalline additive and polypropylene fibres stored at different levels of humidity for 28 days. The influence of crystalline additive on strength was studied as well and the results show that crystalline additives improves the 28-day strength of the mortars.
- 10 January 2018
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 382, 254-260
Influence of a Crystalline Additive on the Porosity of Cement Mortars
The pore structure of a material radically infuences its properties, such as strength, freeze-thaw resistance, capillarity or resistance to elevated temperatures. The character of the pore structure is also limiting for the intrusion of aggressive oxides into the material, which affects its service life. The paper describes how a crystalline additive influences the pore structure of cement mortars. It describes the effect of secondary crystallisation and the influence of the additon of PP fibers on the apparent porosity and the internal structure of the mortar. It also discusses the influence of aggressive conditions on the mortar’s pore structure.
- 10 January 2018
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 382, 254-260
Influence of a Crystalline Additive on the Porosity of Cement Mortars
The pore structure of a material radically infuences its properties, such as strength, freeze-thaw resistance, capillarity or resistance to elevated temperatures. The character of the pore structure is also limiting for the intrusion of aggressive oxides into the material, which affects its service life. The paper describes how a crystalline additive influences the pore structure of cement mortars. It describes the effect of secondary crystallisation and the influence of the additon of PP fibers on the apparent porosity and the internal structure of the mortar. It also discusses the influence of aggressive conditions on the mortar’s pore structure.
- 10 January 2018
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 382, 246-253
Durability of Cement Based Mortars Containing Crystalline Additives
The paper focuses on the study of the durability of cement mortars made with secondary crystallization additives. It investigates the influence of the crystalline additives on the degradation process of cement mortars exposed to gaseous CO2 and freezing cycles. The specimens with were tested for compressive and flexural strength at the following ages and after being treated by the following curing techniques: 28 days, 180 days and 25 freezing cycles, 28 days and 180 days in gaseous CO2. In order to explain the obtained results and to gain new information about the microstructure of the cement mortars being studied, the SEM sampling and RDA analysis were performed. The research results confirm an improvement in the resistance of cement based mortars using crystalline additives against cyclic freezing as well as gaseous CO2. An important parameter that influences the effectiveness of the crystalline additive is the curing conditions during the first 28 days of ageing.
- 10 January 2018
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 382, 246-253
Durability of Cement Based Mortars Containing Crystalline Additives
The paper focuses on the study of the durability of cement mortars made with secondary crystallization additives. It investigates the influence of the crystalline additives on the degradation process of cement mortars exposed to gaseous CO2 and freezing cycles. The specimens with were tested for compressive and flexural strength at the following ages and after being treated by the following curing techniques: 28 days, 180 days and 25 freezing cycles, 28 days and 180 days in gaseous CO2. In order to explain the obtained results and to gain new information about the microstructure of the cement mortars being studied, the SEM sampling and RDA analysis were performed. The research results confirm an improvement in the resistance of cement based mortars using crystalline additives against cyclic freezing as well as gaseous CO2. An important parameter that influences the effectiveness of the crystalline additive is the curing conditions during the first 28 days of ageing.