Lenka Nevřivová
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lenka Nevřivová has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- David Zemánek
Brno University of Technology
6 shared publications - Matěj Lédl
Brno University of Technology
3 shared publications Nikol Žižková
Brno University of Technology
3 shared publicationsVít Petranek
Brno University of Technology
3 shared publicationsDorothea Sklenářová
Brno University of Technology
2 shared publicationsJana Majerová
Brno University of Technology
2 shared publications
Latest Publications
- 30 October 2023
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 352, 109-114
Lightweight Refractory Materials in Al-Si Binary System Produced by Sol-Gel Method
Lightweight refractory materials are most used as a second layer in the lining. Many techniques can be used to their production depending on their final application. This manuscript is focused on utilization of sol-gel method as the replacement of hydraulic or ceramic bond in the manufacturing process of grog and castable preparation. The results show possible ways to produce high quality lightweight refractory grog with very high purity and also lightweight refractory castable, which performs good results in terms of bulk density, apparent porosity, cold crushing strength, cold modulus of rupture and permanent linear changes.
- 30 October 2023
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 352, 109-114
Lightweight Refractory Materials in Al-Si Binary System Produced by Sol-Gel Method
Lightweight refractory materials are most used as a second layer in the lining. Many techniques can be used to their production depending on their final application. This manuscript is focused on utilization of sol-gel method as the replacement of hydraulic or ceramic bond in the manufacturing process of grog and castable preparation. The results show possible ways to produce high quality lightweight refractory grog with very high purity and also lightweight refractory castable, which performs good results in terms of bulk density, apparent porosity, cold crushing strength, cold modulus of rupture and permanent linear changes.
- 27 October 2023
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 351, 47-52
The Effect of the Type of Gelling Agent on the Speed of Gelation of Sol-Gels
This article deals with the selection of a suitable gelling agent for refractory castable with a sol-gel binder system. The goal is to find the optimal ratio between gelation time, content, and concentration of the solution. Various salts (NaCl, NH4Cl, Ca(NO3)2) are investigated as gelling agents. Gelation curves are constructed from gelation time observations. For the design of the formula of refractory castable with a sol-gel bond, it is important to know the behavior of the sol after mixing with the gelling agent. This is the goal of the experiment. In the end, we will obtain initial data for further proposals for the composition of refractory castable with a sol-gel bond.
- 27 October 2023
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 351, 47-52
The Effect of the Type of Gelling Agent on the Speed of Gelation of Sol-Gels
This article deals with the selection of a suitable gelling agent for refractory castable with a sol-gel binder system. The goal is to find the optimal ratio between gelation time, content, and concentration of the solution. Various salts (NaCl, NH4Cl, Ca(NO3)2) are investigated as gelling agents. Gelation curves are constructed from gelation time observations. For the design of the formula of refractory castable with a sol-gel bond, it is important to know the behavior of the sol after mixing with the gelling agent. This is the goal of the experiment. In the end, we will obtain initial data for further proposals for the composition of refractory castable with a sol-gel bond.
- 27 October 2023
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 351, 61-66
The Effect of the Gelling Agent on the Gelation Rate and the Formed Sol-Gel Structure
In this paper a combination of colloidal silica and different gelling agents are studied in order to observe the effect of gelation rate on the formed sol-gel structure. Proper ratios of sol matrix materials and gelation agents were determined. Sets of samples based on these recipes were prepared with added filling material and tested for mechanical properties. Samples with added solution of NaCl gelling agent showed the highest flexural strength observed and also lower doses of this gelling agent are required for one of the studied sols which can positively effect the final price of product.
- 27 October 2023
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 351, 61-66
The Effect of the Gelling Agent on the Gelation Rate and the Formed Sol-Gel Structure
In this paper a combination of colloidal silica and different gelling agents are studied in order to observe the effect of gelation rate on the formed sol-gel structure. Proper ratios of sol matrix materials and gelation agents were determined. Sets of samples based on these recipes were prepared with added filling material and tested for mechanical properties. Samples with added solution of NaCl gelling agent showed the highest flexural strength observed and also lower doses of this gelling agent are required for one of the studied sols which can positively effect the final price of product.
- 18 October 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1071, 241-246
Corrosion Properties of Castables with Various Calcium Oxide Content
This article is focused to investigate the corrosion resistance of LCC, ULCC and NCC. Castables microstructure is one of the key factors influencing corrosion resistance, therefore new fine matrix was designed. Potassium carbonate was used as a corrosive medium using static crucible method for tested castables. The corrosion mechanism was evaluated by Scanning Electron Microscopy (SEM) with EDX probe. The experimental results disclosed that corrosion resistance was improved with decreasing calcium oxide content of tested castables.
- 18 October 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1071, 241-246
Corrosion Properties of Castables with Various Calcium Oxide Content
This article is focused to investigate the corrosion resistance of LCC, ULCC and NCC. Castables microstructure is one of the key factors influencing corrosion resistance, therefore new fine matrix was designed. Potassium carbonate was used as a corrosive medium using static crucible method for tested castables. The corrosion mechanism was evaluated by Scanning Electron Microscopy (SEM) with EDX probe. The experimental results disclosed that corrosion resistance was improved with decreasing calcium oxide content of tested castables.
- 11 October 2021
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 325, 188-193
Analysis of Alkali Oxides Influence on the Microstructure of Refractory Grog
The development and subsequent production of these special kind of grog from raw materials available in the Czech Republic is one of the possibilities how to reduce income costs for the production of refractory materials with specific properties. The experimental work is focused on verifying the possibility of producing grog with increased alumina content from available raw materials. The raw materials are kaolins and claystones. To achieve a higher content of alumina in the grog, waste mullite dust is used. In order to improve the physical and mechanical properties of the grog, modifiers are used. Selected modifiers are expected to affect positively on the resulting density while maintaining the heat properties.
- 11 October 2021
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 325, 188-193
Analysis of Alkali Oxides Influence on the Microstructure of Refractory Grog
The development and subsequent production of these special kind of grog from raw materials available in the Czech Republic is one of the possibilities how to reduce income costs for the production of refractory materials with specific properties. The experimental work is focused on verifying the possibility of producing grog with increased alumina content from available raw materials. The raw materials are kaolins and claystones. To achieve a higher content of alumina in the grog, waste mullite dust is used. In order to improve the physical and mechanical properties of the grog, modifiers are used. Selected modifiers are expected to affect positively on the resulting density while maintaining the heat properties.
- 26 July 2021
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 321, 125-130
Influence of Colloidal Silica on Final Properties of no Cement Castables
This paper deals with sol-gel process and application in no cement castables based on andalusite. The use of calcium free binder increases the refractory parameters of material and allows its faster drying. Six colloidal sols from CWK Bad Köstritz based on SiO2 were tested, which differed not only in concentration and particle size, but also in pH. The influence of silica sols on the consistency of fresh castable, initial setting and final setting times were investigated. Furthermore, basic parameters after firing, such as bulk density, apparent porosity, flexural and compressive strength, were tested.
- 26 July 2021
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 321, 125-130
Influence of Colloidal Silica on Final Properties of no Cement Castables
This paper deals with sol-gel process and application in no cement castables based on andalusite. The use of calcium free binder increases the refractory parameters of material and allows its faster drying. Six colloidal sols from CWK Bad Köstritz based on SiO2 were tested, which differed not only in concentration and particle size, but also in pH. The influence of silica sols on the consistency of fresh castable, initial setting and final setting times were investigated. Furthermore, basic parameters after firing, such as bulk density, apparent porosity, flexural and compressive strength, were tested.
- 26 July 2021
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 321, 149-155
Factors Influencing Mullite Formation in Refractory Grog
The mineral mullite has many outstanding refractory properties. The content of aluminum oxide in the raw material is the basic factor influencing the content of mullite in the final product. Depending on Al2O3 content, silica-alumina materials can be divided into fireclay and high-alumina with the Al2O3 content of 45 % and more. The study describes the influence of raw material, the influence of homogenization of raw material and influence of firing temperature on the mullite formation in fireclay refractory material. Three kinds of refractory clay with different chemical composition were used as raw material for fireclay grog production. Three kinds of homogenization and three different temperatures were studied as factors influencing mullite formation. Powder X-ray diffraction was used to determine mullite content in material. Quantitative phase analysis was conducted by the Rietveld method. Mullite crystals morphology was observed by scanning electron microscopy.
- 26 July 2021
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 321, 149-155
Factors Influencing Mullite Formation in Refractory Grog
The mineral mullite has many outstanding refractory properties. The content of aluminum oxide in the raw material is the basic factor influencing the content of mullite in the final product. Depending on Al2O3 content, silica-alumina materials can be divided into fireclay and high-alumina with the Al2O3 content of 45 % and more. The study describes the influence of raw material, the influence of homogenization of raw material and influence of firing temperature on the mullite formation in fireclay refractory material. Three kinds of refractory clay with different chemical composition were used as raw material for fireclay grog production. Three kinds of homogenization and three different temperatures were studied as factors influencing mullite formation. Powder X-ray diffraction was used to determine mullite content in material. Quantitative phase analysis was conducted by the Rietveld method. Mullite crystals morphology was observed by scanning electron microscopy.
- 17 March 2020
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 834, 75-81
Pore Structure Regulation in Refractory Grog with Alumina Content over 45 %
Increased alumina content in refractory grog is a product of the grog’s firing and, at the same time, it is a raw material used for the production of dense or insulating, shaped or monolithic refractories. Grog characteristics determine the properties of the final product. The specific characteristics of the grog are therefore optimized to suit the refractory product as close as possible. The basic characteristics determining the nature of the grog include its mineralogical composition, chemical composition, and apparent porosity. The present study focuses on ways of reducing the porosity of a high-alumina grog and thus obtaining a raw material suitable for the production of dense refractory materials. The experiments have shown that it is possible to regulate porosity by using clay with better sinterability and phosphoric acid in the production of grog from claystone with alumina content over 40 %, a minimal Fe2O3 content, a minimal content of CaO and alkali oxides.
- 17 March 2020
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 834, 75-81
Pore Structure Regulation in Refractory Grog with Alumina Content over 45 %
Increased alumina content in refractory grog is a product of the grog’s firing and, at the same time, it is a raw material used for the production of dense or insulating, shaped or monolithic refractories. Grog characteristics determine the properties of the final product. The specific characteristics of the grog are therefore optimized to suit the refractory product as close as possible. The basic characteristics determining the nature of the grog include its mineralogical composition, chemical composition, and apparent porosity. The present study focuses on ways of reducing the porosity of a high-alumina grog and thus obtaining a raw material suitable for the production of dense refractory materials. The experiments have shown that it is possible to regulate porosity by using clay with better sinterability and phosphoric acid in the production of grog from claystone with alumina content over 40 %, a minimal Fe2O3 content, a minimal content of CaO and alkali oxides.
- 16 August 2019
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 296, 197-202
The Influence of Al2O3 Microparticles on the Pore Structure of Fired Clay
Contemporary demand after high-quality ceramics leads to the depletion of raw material deposits. The industry also produces waste secondary materials that cannot be used directly for the desired purposes. It is therefore necessary to find other uses for these materials. It is common practice in the ceramics industry to stockpile fine fractions of refractory clays prior to their firing in a shaft kiln. These fractions have the size of 35 mm and less and when stored in a mound are facing a risk of weathering. Finding a purpose for these unused materials will markedly slow down fresh clay mining and make the production more eco-friendly and cost-effective. This paper seeks a suitable technology of treating fine fractions of BC (Brezina Clay), sometimes called FBC (Fine Brezina Clay), prior to its being fired into grog. The stockpiles hold tens of thousands of tons of these fractions. The properties of the fired clay are determined by the length of time for which the material has been stockpiled, moisture content, of the clay, as well as the briquetting pressure before firing in a shaft kiln. FBC contains approx. 41 % of aluminium oxide. This amount is not high enough for certain applications. The aluminium oxide content can be increased by the addition of bauxite, corundum, mullite, kaolin, clays rich in Al2O3, or technical Al2O3. The experiment described in this paper tested how the addition of technical Al2O3 affects the pore structure of fired FBC, which is later used as a grog in both shaped and non-shaped refractory products. The influence of firing temperature on the material's mineralogy was examined as well
- 16 August 2019
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 296, 197-202
The Influence of Al2O3 Microparticles on the Pore Structure of Fired Clay
Contemporary demand after high-quality ceramics leads to the depletion of raw material deposits. The industry also produces waste secondary materials that cannot be used directly for the desired purposes. It is therefore necessary to find other uses for these materials. It is common practice in the ceramics industry to stockpile fine fractions of refractory clays prior to their firing in a shaft kiln. These fractions have the size of 35 mm and less and when stored in a mound are facing a risk of weathering. Finding a purpose for these unused materials will markedly slow down fresh clay mining and make the production more eco-friendly and cost-effective. This paper seeks a suitable technology of treating fine fractions of BC (Brezina Clay), sometimes called FBC (Fine Brezina Clay), prior to its being fired into grog. The stockpiles hold tens of thousands of tons of these fractions. The properties of the fired clay are determined by the length of time for which the material has been stockpiled, moisture content, of the clay, as well as the briquetting pressure before firing in a shaft kiln. FBC contains approx. 41 % of aluminium oxide. This amount is not high enough for certain applications. The aluminium oxide content can be increased by the addition of bauxite, corundum, mullite, kaolin, clays rich in Al2O3, or technical Al2O3. The experiment described in this paper tested how the addition of technical Al2O3 affects the pore structure of fired FBC, which is later used as a grog in both shaped and non-shaped refractory products. The influence of firing temperature on the material's mineralogy was examined as well
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 242-247
Use of Undersize Fractions of Refractory Claystone for Grog Manufacturing in Shaft Kilns
Refractory aluminosilicate grogs are made by firing refractory clays and claystones. They are fired predominantly in rotary or shaft kilns. Prior to firing in shaft kilns, particles of claystone smaller than 35 mm are separated These fine fractions cannot be processed in a shaft kiln, since they lower the quality and homogeneity of firing. However, these claystones can be briquetted into larger pieces (5 – 6 cm), which can be easily fired in shaft kilns. It is possible to modify the raw material by adding correcting materials or other types of clay. This method can then be used for making special grogs. The paper discusses the possibilities of manufacturing grog with an increased Al2O3 content with undersize fractions of claystone mined in Březinka. The research focused on the influence of raw material water content and compacting pressure on the final properties of fireclay grog, and determining the influence of firing temperature on the properties of the grog.
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 242-247
Use of Undersize Fractions of Refractory Claystone for Grog Manufacturing in Shaft Kilns
Refractory aluminosilicate grogs are made by firing refractory clays and claystones. They are fired predominantly in rotary or shaft kilns. Prior to firing in shaft kilns, particles of claystone smaller than 35 mm are separated These fine fractions cannot be processed in a shaft kiln, since they lower the quality and homogeneity of firing. However, these claystones can be briquetted into larger pieces (5 – 6 cm), which can be easily fired in shaft kilns. It is possible to modify the raw material by adding correcting materials or other types of clay. This method can then be used for making special grogs. The paper discusses the possibilities of manufacturing grog with an increased Al2O3 content with undersize fractions of claystone mined in Březinka. The research focused on the influence of raw material water content and compacting pressure on the final properties of fireclay grog, and determining the influence of firing temperature on the properties of the grog.