Sabit Adanur
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sabit Adanur has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Ajay Jayswal
Chemical Sciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Rd, Oak Ridge, Tennessee 37830, United States
8 shared publications - Ashok Sapkota
Department of Mechanical Engineering Auburn University Auburn Alabama USA
3 shared publications - Shree Kaji Ghimire
Auburn University
3 shared publications Wei Liu
Intertek Consumer Goods NA, Arlington Heights, IL UNITED STATES
3 shared publications- Yang Shen
Key Laboratory of Geomechanics and Embankment Engineering of Ministry of Education, Hohai University, Nanjing, 210024, PR China
3 shared publications Birgul Ascioglu
Polymer and Fiber Engineering Department, Auburn University, Auburn, AL 36849, USA
2 shared publications
Latest Publications
- Open Access
- 30 November 2025
- Published by Tresearch in Textile Science & Research Journal
- Vol. 1 (1) , 01-21
Optimization of design and FDM Process Parameters for Enhanced Mechanical Performance of 3D Printed Woven Fabric Structures
Fused Deposition Modeling (FDM) is a widely used additive manufacturing technique capable of producing textile-like structures using thermoplastic polymers. This study focuses on optimizing 3D printed woven fabrics using PLA filament. Mechanical characterization through tensile and flexural testing was conducted in both warp and weft directions. A Taguchi L9 orthogonal array was employed for efficient experimental design. The results were analyzed using response table and main effect plots, and the mechanical properties were optimized using regression modeling in MINITAB. Findings reveal that different properties are governed by different parameters. Layer height significantly influenced strength while design played a key role in modulus. Directional anisotropy was observed with notable differences in mechanical behavior between warp and weft orientations. Optimal parameter combinations were identified for individual properties. Twill design with higher layer height and temperature showed enhanced flexibility, while basket weaves with moderate settings favored strength. The study provides valuable insights for tailoring FDM-printed textile structures, paving the way for high-performance, customizable, and scalable fabric applications.
- 30 November 2025
- Published by Tresearch in Textile Science & Research Journal
- Vol. 1 (1) , 01-21
Open AccessOptimization of design and FDM Process Parameters for Enhanced Mechanical Performance of 3D Printed Woven Fabric Structures
Fused Deposition Modeling (FDM) is a widely used additive manufacturing technique capable of producing textile-like structures using thermoplastic polymers. This study focuses on optimizing 3D printed woven fabrics using PLA filament. Mechanical characterization through tensile and flexural testing was conducted in both warp and weft directions. A Taguchi L9 orthogonal array was employed for efficient experimental design. The results were analyzed using response table and main effect plots, and the mechanical properties were optimized using regression modeling in MINITAB. Findings reveal that different properties are governed by different parameters. Layer height significantly influenced strength while design played a key role in modulus. Directional anisotropy was observed with notable differences in mechanical behavior between warp and weft orientations. Optimal parameter combinations were identified for individual properties. Twill design with higher layer height and temperature showed enhanced flexibility, while basket weaves with moderate settings favored strength. The study provides valuable insights for tailoring FDM-printed textile structures, paving the way for high-performance, customizable, and scalable fabric applications.
- Open Access
- 29 April 2025
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 55
Fused deposition modeling (FDM) process parameter optimization for mechanical properties of 3D-printed woven fabric structures using Taguchi method
Fused deposition modeling (FDM) process parameters influence the mechanical behavior of the printed parts. Optimization of parameters like extrusion temperature, layer height, print speed and infill density enhances the performance of the product. The ability to process a variety of thermoplastic materials and quick and personalized design makes FDM a desirable alternative process to manufacture fabric structures. However, the mechanical properties are often compromised. This research attempts to optimize extrusion temperature, layer height and print speed for manufacturing of 2/1 twill woven fabric structure for desired properties. In this work, Taguchi robust design is used for experimental design. Samples from Polylactic acid (PLA) are subjected to tensile and flexural loading. Tensile strength, tensile modulus, flexural strength and flexural modulus are recorded and optimized using commercial software MINITAB. The order of influence of process parameters on fabric is varied for different properties evaluated. Either extrusion temperature or layer height is reported to be the most influential process parameter for the fabric sample. In contrast, print speed does not have significant effect on most of the properties studied. The mechanical properties and nature of influence by process parameters are found to be dissimilar in warp and weft direction.
- 29 April 2025
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 55
Open AccessFused deposition modeling (FDM) process parameter optimization for mechanical properties of 3D-printed woven fabric structures using Taguchi method
Fused deposition modeling (FDM) process parameters influence the mechanical behavior of the printed parts. Optimization of parameters like extrusion temperature, layer height, print speed and infill density enhances the performance of the product. The ability to process a variety of thermoplastic materials and quick and personalized design makes FDM a desirable alternative process to manufacture fabric structures. However, the mechanical properties are often compromised. This research attempts to optimize extrusion temperature, layer height and print speed for manufacturing of 2/1 twill woven fabric structure for desired properties. In this work, Taguchi robust design is used for experimental design. Samples from Polylactic acid (PLA) are subjected to tensile and flexural loading. Tensile strength, tensile modulus, flexural strength and flexural modulus are recorded and optimized using commercial software MINITAB. The order of influence of process parameters on fabric is varied for different properties evaluated. Either extrusion temperature or layer height is reported to be the most influential process parameter for the fabric sample. In contrast, print speed does not have significant effect on most of the properties studied. The mechanical properties and nature of influence by process parameters are found to be dissimilar in warp and weft direction.
- 4 February 2025
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 31 (5) , 934-949
Effect of FDM process parameters on mechanical properties of 3D-printed fabrics and yarns from polyethylene terephthalate glycol, nylon and thermoplastic polyurethane
Purpose: Optimization of FDM process parameters has emerged as a major step toward mitigating the issue of reduced mechanical strength of fused deposition modeling (FDM) products. This study aims to evaluate the impact of process parameters on the mechanical properties of 3D-printed fabric yarns of three different materials, namely, polyethylene terephthalate glycol (PETG), nylon and thermoplastic polyurethane (TPU). Design/methodology/approach: 2/1 Twill fabric samples with variations of extrusion temperatures and printing profiles are produced, and the individual yarns, manually separated from the fabric samples, are tested for tensile strength, modulus, strain and energy at maximum force. The tensile test results are further subjected to statistical analysis with MINITAB software to detect the standard level of influence of each parameter and evaluate their significance. Findings: Both extrusion temperature and printing profile, along with their interaction, are significantly important parameters for the mechanical behavior of PETG. However, for nylon and TPU, the influence of a few parameters is found to be insignificant. For all variations of fabric yarns, relatively lower extrusion temperature is concluded to be preferable for better mechanical properties. Originality/value: This research is new and original. It provides knowledge about how FDM process parameters influence the mechanical behavior of fabrics. It also identifies the optimum process parameters for the best performance of the final product. This article can be a foundation for further parametric analysis of 3D-printed fabric. No artificial intelligence or similar software was used in the preparation of this manuscript.
- 4 February 2025
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 31 (5) , 934-949
Effect of FDM process parameters on mechanical properties of 3D-printed fabrics and yarns from polyethylene terephthalate glycol, nylon and thermoplastic polyurethane
Purpose: Optimization of FDM process parameters has emerged as a major step toward mitigating the issue of reduced mechanical strength of fused deposition modeling (FDM) products. This study aims to evaluate the impact of process parameters on the mechanical properties of 3D-printed fabric yarns of three different materials, namely, polyethylene terephthalate glycol (PETG), nylon and thermoplastic polyurethane (TPU). Design/methodology/approach: 2/1 Twill fabric samples with variations of extrusion temperatures and printing profiles are produced, and the individual yarns, manually separated from the fabric samples, are tested for tensile strength, modulus, strain and energy at maximum force. The tensile test results are further subjected to statistical analysis with MINITAB software to detect the standard level of influence of each parameter and evaluate their significance. Findings: Both extrusion temperature and printing profile, along with their interaction, are significantly important parameters for the mechanical behavior of PETG. However, for nylon and TPU, the influence of a few parameters is found to be insignificant. For all variations of fabric yarns, relatively lower extrusion temperature is concluded to be preferable for better mechanical properties. Originality/value: This research is new and original. It provides knowledge about how FDM process parameters influence the mechanical behavior of fabrics. It also identifies the optimum process parameters for the best performance of the final product. This article can be a foundation for further parametric analysis of 3D-printed fabric. No artificial intelligence or similar software was used in the preparation of this manuscript.
- Top Cited PapersOpen Access
- 1 January 2024
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 54
A review on fused deposition modeling (FDM)-based additive manufacturing (AM) methods, materials and applications for flexible fabric structures
Fused Deposition Modeling (FDM) is an extrusion type additive manufacturing (AM) method in which a molten polymer is selectively extruded in layer-by-layer manner. Although there are several other AM techniques, FDM is a suitable method to produce fabric structures as it is capable of processing polymers and is widely used in various engineering applications. This article summarizes the current research works in characterization of FDM parts, advancements in materials used in FDM and latest works related to making fabric samples using FDM. The results show that the mechanical properties and surface quality are compromised in FDM parts. Strength and flexibility with better surface finishing are essential parameters in fabric structures. There are mainly two techniques that are explored by researchers to enhance the quality of the parts. The first is optimizing process parameters and the second is improving material quality. FDM process parameters like extrusion temperature, layer height, print speed and built orientation can significantly influence the quality of the parts. Optimizing these parameters can significantly enhance the strength of the fabric produced. Moreover, a great amount of impetus is given to improve material by reinforcing it and making polymer blends with specific qualities. There has been studies related to the development of fabric structures and deposition of polymers on fabrics with FDM. It is concluded that the major concern with such structures is strength and processability. To address these issues, optimizing process parameters and developing new filaments for exclusively making fabrics can be the future work in this area.
- 1 January 2024
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 54
Top Cited PapersOpen AccessA review on fused deposition modeling (FDM)-based additive manufacturing (AM) methods, materials and applications for flexible fabric structures
Fused Deposition Modeling (FDM) is an extrusion type additive manufacturing (AM) method in which a molten polymer is selectively extruded in layer-by-layer manner. Although there are several other AM techniques, FDM is a suitable method to produce fabric structures as it is capable of processing polymers and is widely used in various engineering applications. This article summarizes the current research works in characterization of FDM parts, advancements in materials used in FDM and latest works related to making fabric samples using FDM. The results show that the mechanical properties and surface quality are compromised in FDM parts. Strength and flexibility with better surface finishing are essential parameters in fabric structures. There are mainly two techniques that are explored by researchers to enhance the quality of the parts. The first is optimizing process parameters and the second is improving material quality. FDM process parameters like extrusion temperature, layer height, print speed and built orientation can significantly influence the quality of the parts. Optimizing these parameters can significantly enhance the strength of the fabric produced. Moreover, a great amount of impetus is given to improve material by reinforcing it and making polymer blends with specific qualities. There has been studies related to the development of fabric structures and deposition of polymers on fabrics with FDM. It is concluded that the major concern with such structures is strength and processability. To address these issues, optimizing process parameters and developing new filaments for exclusively making fabrics can be the future work in this area.
- 31 August 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 63 (11) , 3809-3818
Creep behavior of 3D printed polymer composites
The creep behavior of polymer composites containing different weight percentages of poly(lactic) acid (PLA), thermoplastic polyurethane (TPU), and poly(ethylene) glycol (PEG) is experimentally characterized and computationally modeled using finite element analysis (FEA). The composite filaments are manufactured with melt extrusion method by using twin‐screw extruders, and then are employed in the 3D printing of creep samples. The samples are tested under a constant tensile load of 100 N. In this study, the computational model is developed by using the Generalized Voigt‐Kelvin solid model and three terms in Prony series. The equations of Prony series were obtained by the Laplace transformation of Kelvin model. The experimental creep displacements and strains are compared with computational results, and a good agreement between them is observed. The maximum error percentage in computational result is approximately 6% as compared to the experimental result. Hence, it can be said that the relatively simple computational models developed are reliable and can be used to study the creep behavior of similar polymers. The error percentages can still be reduced by considering a higher number of terms of Prony series in the model.Highlights: Studied creep behavior for additively manufactured thermoplastic polymer composites. Developed computational model using three terms of relaxation modulus. The experimental results correlate very well with the computational model. Computational models can be used for other polymers.
- 31 August 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 63 (11) , 3809-3818
Creep behavior of 3D printed polymer composites
The creep behavior of polymer composites containing different weight percentages of poly(lactic) acid (PLA), thermoplastic polyurethane (TPU), and poly(ethylene) glycol (PEG) is experimentally characterized and computationally modeled using finite element analysis (FEA). The composite filaments are manufactured with melt extrusion method by using twin‐screw extruders, and then are employed in the 3D printing of creep samples. The samples are tested under a constant tensile load of 100 N. In this study, the computational model is developed by using the Generalized Voigt‐Kelvin solid model and three terms in Prony series. The equations of Prony series were obtained by the Laplace transformation of Kelvin model. The experimental creep displacements and strains are compared with computational results, and a good agreement between them is observed. The maximum error percentage in computational result is approximately 6% as compared to the experimental result. Hence, it can be said that the relatively simple computational models developed are reliable and can be used to study the creep behavior of similar polymers. The error percentages can still be reduced by considering a higher number of terms of Prony series in the model.Highlights: Studied creep behavior for additively manufactured thermoplastic polymer composites. Developed computational model using three terms of relaxation modulus. The experimental results correlate very well with the computational model. Computational models can be used for other polymers.
- 25 April 2023
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 115 (6) , 893-903
Additive manufacturing of weft knitted and braided fabric structures with fused deposition modeling
Additive manufacturing (AM), also commonly called three-dimensional (3D) printing, allows fabrication of complex objects within a limited time frame with minimal waste production. The purpose of this research is to design, 3D print, and analyze the mechanical properties of fabric structures. Two different fabric types are considered for this work: weft knit fabric and braided fabric structures. A single yarn and weft knitted fabric structure were designed, fabricated and weft knitted fabrics are tested. Different designs of braided structures such as diamond braid, regular braid, Hercules braid, triaxial braid, and bi-furcated braid are designed, fabricated, and tested. Poly(lactic) acid (PLA) filaments were used to print the fabric structures. Mechanical properties and morphological structures were studied using the printed structures. The results showed that weft knitted fabrics possess a good ductile response before failure showing a tensile displacement in the range of 12–15 mm, and the peak force exhibited is nearly 250 N. On the other hand, the maximum flexural displacement is approximately 10 mm, and the load is in the range of 15–22 N in the wale direction, and 85–95 N in the course direction. Braided structures showed that they can bear significant amount of compressive load having displacement at failure of more than 25 mm. Optical microscope (OM) analysis showed that the yarns contain voids and cracks that contributed to the failure of the samples. The additively manufactured weft knitted fabric structures can be used in wearable, filtration, and geotextiles applications whereas the circular braided structures can be used in shock absorption applications.
- 25 April 2023
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 115 (6) , 893-903
Additive manufacturing of weft knitted and braided fabric structures with fused deposition modeling
Additive manufacturing (AM), also commonly called three-dimensional (3D) printing, allows fabrication of complex objects within a limited time frame with minimal waste production. The purpose of this research is to design, 3D print, and analyze the mechanical properties of fabric structures. Two different fabric types are considered for this work: weft knit fabric and braided fabric structures. A single yarn and weft knitted fabric structure were designed, fabricated and weft knitted fabrics are tested. Different designs of braided structures such as diamond braid, regular braid, Hercules braid, triaxial braid, and bi-furcated braid are designed, fabricated, and tested. Poly(lactic) acid (PLA) filaments were used to print the fabric structures. Mechanical properties and morphological structures were studied using the printed structures. The results showed that weft knitted fabrics possess a good ductile response before failure showing a tensile displacement in the range of 12–15 mm, and the peak force exhibited is nearly 250 N. On the other hand, the maximum flexural displacement is approximately 10 mm, and the load is in the range of 15–22 N in the wale direction, and 85–95 N in the course direction. Braided structures showed that they can bear significant amount of compressive load having displacement at failure of more than 25 mm. Optical microscope (OM) analysis showed that the yarns contain voids and cracks that contributed to the failure of the samples. The additively manufactured weft knitted fabric structures can be used in wearable, filtration, and geotextiles applications whereas the circular braided structures can be used in shock absorption applications.
- 6 April 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 63 (6) , 1725-1736
Thermomechanical behavior of three dimensionally printed fabric structures
Additive manufacturing of fabrics is an emerging research topic with potential applications in several industries including high performance wearable products and high‐temperature textiles. Therefore, thermal, mechanical, and viscoelastic properties of such fabrics need to be determined. In this research, the thermomechanical behavior of additively manufactured plain weave fabrics at and above glass transition temperature ( is studied. The time‐dependent mechanical response using a viscoelastic material model is represented by a Prony series as a function of frequency (f). Unit cells of plain weave fabrics are additively manufactured using poly(lactic) acid (PLA). Tensile and compression tests were performed on unit cells in a thermal environment using dynamic mechanical analysis (DMA). A multiphysics finite element model is implemented to duplicate the experimental setup. The experimental results are compared with that of computational results. The relative error percentages in the peak forces at each temperature are 23.60% at 60°C, −8.85% at 65°C, and −6.25% at 70°C. A better agreement in peak forces is seen for unit cells above Tg. The computational model developed for unit cells is used to predict the thermomechanical‐viscoelastic response of large additively manufactured fabric structures which is difficult to evaluate experimentally.
- 6 April 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 63 (6) , 1725-1736
Thermomechanical behavior of three dimensionally printed fabric structures
Additive manufacturing of fabrics is an emerging research topic with potential applications in several industries including high performance wearable products and high‐temperature textiles. Therefore, thermal, mechanical, and viscoelastic properties of such fabrics need to be determined. In this research, the thermomechanical behavior of additively manufactured plain weave fabrics at and above glass transition temperature ( is studied. The time‐dependent mechanical response using a viscoelastic material model is represented by a Prony series as a function of frequency (f). Unit cells of plain weave fabrics are additively manufactured using poly(lactic) acid (PLA). Tensile and compression tests were performed on unit cells in a thermal environment using dynamic mechanical analysis (DMA). A multiphysics finite element model is implemented to duplicate the experimental setup. The experimental results are compared with that of computational results. The relative error percentages in the peak forces at each temperature are 23.60% at 60°C, −8.85% at 65°C, and −6.25% at 70°C. A better agreement in peak forces is seen for unit cells above Tg. The computational model developed for unit cells is used to predict the thermomechanical‐viscoelastic response of large additively manufactured fabric structures which is difficult to evaluate experimentally.
- 13 March 2023
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (12) , 4800-4825
Thermo-mechanical properties of composite filaments for 3D printing of fabrics
The objective of this study is to manufacture composite filaments to be used in three-dimensional (3D) printing of fabrics using fused deposition modeling (FDM) method. The primary properties of a fabric are flexibility and strength which are lacking in the available 3D printed materials. Polylactic acid (PLA), thermoplastic polyurethane (TPU) and poly(ethylene) glycol (PEG) were blended in different proportions and extruded using twin-screw extruder to obtain composite filaments. The properties of the filaments were studied using various material characterization methods such as uniaxial tensile test, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscope (SEM). With the addition of PEG in the PLA/TPU composition, it was found that the yield stress and Young’s modulus of the composite filaments have significantly decreased compared to that of pure PLA filament. It was also noted that there was no significant difference in ultimate tensile strength whereas the elongation at break was increased by more than 500%. Using the composite filament, a plain weave fabric structure was 3D printed to investigate the printing ability of a complex structure. It is concluded that the composite filaments developed are suitable for 3D printing but non-uniformity in diameter affects the print quality and hence the overall properties of fabrics.
- 13 March 2023
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (12) , 4800-4825
Thermo-mechanical properties of composite filaments for 3D printing of fabrics
The objective of this study is to manufacture composite filaments to be used in three-dimensional (3D) printing of fabrics using fused deposition modeling (FDM) method. The primary properties of a fabric are flexibility and strength which are lacking in the available 3D printed materials. Polylactic acid (PLA), thermoplastic polyurethane (TPU) and poly(ethylene) glycol (PEG) were blended in different proportions and extruded using twin-screw extruder to obtain composite filaments. The properties of the filaments were studied using various material characterization methods such as uniaxial tensile test, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscope (SEM). With the addition of PEG in the PLA/TPU composition, it was found that the yield stress and Young’s modulus of the composite filaments have significantly decreased compared to that of pure PLA filament. It was also noted that there was no significant difference in ultimate tensile strength whereas the elongation at break was increased by more than 500%. Using the composite filament, a plain weave fabric structure was 3D printed to investigate the printing ability of a complex structure. It is concluded that the composite filaments developed are suitable for 3D printing but non-uniformity in diameter affects the print quality and hence the overall properties of fabrics.
- 5 January 2023
- Published by SAGE Publications in Textile Research Journal
- Vol. 93 (11-12) , 2754-2764
A novel face mask design with improved properties for COVID-19 prevention
Novel cloth face masks to mitigate the spread of COVID-19 have been developed and tested for particle (0.1 μm in size) filtration efficiency, bacterial filtration efficiency, breathability, leakage, heart rate, and blood oxygen level, and then compared with the available N95 masks and surgical masks. It was found that this novel mask had better filtration efficiency than that of surgical masks and was very close to that of N95 masks. The breathability was also improved and was in the range of the designated levels for barrier face coverings. The flow visualization technique was utilized to study the leakage of the mask and it was found to have significantly lower leakage as compared to surgical masks. Heart rate and blood oxygen level tests were performed by wearing the mask during 10-minute walking sessions and it was found that wearing the mask did not adversely affect heart rate or blood oxygen levels or add any other strain on the wearer. It is believed that this novel face mask would reduce the spread of COVID-19 as well as provide an environmentally and economically conscious alternative to the N95 respirators for the public. The mask developed in this study can be washed, reused, and therefore worn for longer periods of time.
- 5 January 2023
- Published by SAGE Publications in Textile Research Journal
- Vol. 93 (11-12) , 2754-2764
A novel face mask design with improved properties for COVID-19 prevention
Novel cloth face masks to mitigate the spread of COVID-19 have been developed and tested for particle (0.1 μm in size) filtration efficiency, bacterial filtration efficiency, breathability, leakage, heart rate, and blood oxygen level, and then compared with the available N95 masks and surgical masks. It was found that this novel mask had better filtration efficiency than that of surgical masks and was very close to that of N95 masks. The breathability was also improved and was in the range of the designated levels for barrier face coverings. The flow visualization technique was utilized to study the leakage of the mask and it was found to have significantly lower leakage as compared to surgical masks. Heart rate and blood oxygen level tests were performed by wearing the mask during 10-minute walking sessions and it was found that wearing the mask did not adversely affect heart rate or blood oxygen levels or add any other strain on the wearer. It is believed that this novel face mask would reduce the spread of COVID-19 as well as provide an environmentally and economically conscious alternative to the N95 respirators for the public. The mask developed in this study can be washed, reused, and therefore worn for longer periods of time.
- Open Access
- 1 June 2022
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 52
An overview of additive manufacturing methods, materials, and applications for flexible structures
Various types of additive manufacturing (AM) methods (also called 3D printing), and materials have been increasingly studied in the field of additive manufacturing of flexible structures such as fabrics, and flexible electronics. Polymer-based AM processes allow the flexibility, rapid, and low-cost fabrication of complex geometries depending on the types of materials used. The purpose of this review article is to summarize the major AM methods, materials, and their emerging applications to additively manufacture the flexible structures. In the AM methods section, Fused Deposition Modeling (FDM), and Selective Laser Sintering (SLS) are reviewed for fabrics, and Direct Ink Writing (DIW) for electronics. In the Materials section, the manufacturing methods, chemical structures, properties, advantages, and limitations of some of the widely used materials in three-dimensional (3D) printing of polymers are reviewed. Third, the applications of these methods and materials for fabrics, and electronics are covered. Finally, the associated opportunities and challenges in 3D printing process of flexible structures are described. The future research should be related to the exploration of combinations and development of innovative materials, printing process parameters, detail study on improving the properties, and hybrid 3D printing process.
- 1 June 2022
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 52
Open AccessAn overview of additive manufacturing methods, materials, and applications for flexible structures
Various types of additive manufacturing (AM) methods (also called 3D printing), and materials have been increasingly studied in the field of additive manufacturing of flexible structures such as fabrics, and flexible electronics. Polymer-based AM processes allow the flexibility, rapid, and low-cost fabrication of complex geometries depending on the types of materials used. The purpose of this review article is to summarize the major AM methods, materials, and their emerging applications to additively manufacture the flexible structures. In the AM methods section, Fused Deposition Modeling (FDM), and Selective Laser Sintering (SLS) are reviewed for fabrics, and Direct Ink Writing (DIW) for electronics. In the Materials section, the manufacturing methods, chemical structures, properties, advantages, and limitations of some of the widely used materials in three-dimensional (3D) printing of polymers are reviewed. Third, the applications of these methods and materials for fabrics, and electronics are covered. Finally, the associated opportunities and challenges in 3D printing process of flexible structures are described. The future research should be related to the exploration of combinations and development of innovative materials, printing process parameters, detail study on improving the properties, and hybrid 3D printing process.