Zhibo Dong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zhibo Dong has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Hongyuan Fang
State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China
4 shared publications - Chengcheng Wang
State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Chengkun Li
State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Fang Han
State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Junli Guo
State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China
2 shared publications Kang Yang
College of Aerospace Engineering, Shenyang Aerospace University, Shenyang, China
2 shared publications
Latest Publications
- Open Access
- 1 October 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (10) , 394
Angle-Dependent Inherent Strain in LPBF Overhang Structures: Modeling and Residual Stress Validation
Low-angle overhang structures in laser powder bed fusion (LPBF) experience strongly geometry-dependent thermal conditions because the underlying material progressively changes from consolidated solid to low-conductivity powder, which raises a fundamental question regarding the conventional use of a uniform inherent strain for efficient residual stress and distortion prediction. In this study, the dynamic inherent strain (DIS) method is employed to investigate the inherent strain behavior of LPBF overhang structures with different tilt-angles. The results reveal that after excluding the boundary-affected stages of the build, the representative inherent strain exhibits a systematic dependence on tilt-angle in both magnitude and tensor characteristics. Based on this angle dependence, compact angle-dependent expressions are established using trigonometric basis functions for engineering implementation. Comparisons with residual stress measurements at the experimentally investigated 30° and 90° geometries further indicate that angle-specific inherent strain assignment has a greater influence on the mechanical response toward the lower bound of the investigated angular range.
- 1 October 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (10) , 394
Open AccessAngle-Dependent Inherent Strain in LPBF Overhang Structures: Modeling and Residual Stress Validation
Low-angle overhang structures in laser powder bed fusion (LPBF) experience strongly geometry-dependent thermal conditions because the underlying material progressively changes from consolidated solid to low-conductivity powder, which raises a fundamental question regarding the conventional use of a uniform inherent strain for efficient residual stress and distortion prediction. In this study, the dynamic inherent strain (DIS) method is employed to investigate the inherent strain behavior of LPBF overhang structures with different tilt-angles. The results reveal that after excluding the boundary-affected stages of the build, the representative inherent strain exhibits a systematic dependence on tilt-angle in both magnitude and tensor characteristics. Based on this angle dependence, compact angle-dependent expressions are established using trigonometric basis functions for engineering implementation. Comparisons with residual stress measurements at the experimentally investigated 30° and 90° geometries further indicate that angle-specific inherent strain assignment has a greater influence on the mechanical response toward the lower bound of the investigated angular range.
- Open Access
Heat Transfer and Thermo-Mechanical Analysis of Plastic-Strain Evolution in Laser-Welded Thin-Walled Laminated Cooling Plates with Non-Uniform Stiffness
Thin-walled laminated cooling plates integrate internal channels and pin-fin cores, producing reduced and spatially non-uniform stiffness that changes welding restraint and distortion. This study investigates stiffness-controlled plastic-strain evolution in laser butt welding of GH3230 laminated plates, with geometrically identical solid plates as reference. A coupled heat-transfer and thermo-mechanical finite element model was developed in MSC Marc using a composite Gaussian surface–volumetric moving heat source and temperature-dependent properties. The thermal solution was validated against near-weld thermal cycles and fusion geometry; mechanical predictions were evaluated by CMM distortion and residual-stress measurements. Both structures show comparable residual-stress magnitudes and spatial trends, indicating that residual stress is governed mainly by the local weld thermal gradient. In contrast, the laminated plate exhibits larger angular/bending distortion. Simulations show that, although the plastic-strain pattern is similar, the laminated plate develops higher peak plastic strain confined to a narrower band near the weld, with the transverse plastic strain dominating. Plastic strain–temperature paths reveal continued transverse plastic-strain accumulation during cooling with limited recovery, consistent with restraint redistribution induced by stiffness non-uniformity. An equivalent restraint–stiffness spring model explains this “narrower-but-stronger” plastic zone and links stiffness to yielding and residual plastic-strain magnitude, supporting distortion prediction and stiffness-informed control of welded laminated cooling plates.
Open AccessHeat Transfer and Thermo-Mechanical Analysis of Plastic-Strain Evolution in Laser-Welded Thin-Walled Laminated Cooling Plates with Non-Uniform Stiffness
Thin-walled laminated cooling plates integrate internal channels and pin-fin cores, producing reduced and spatially non-uniform stiffness that changes welding restraint and distortion. This study investigates stiffness-controlled plastic-strain evolution in laser butt welding of GH3230 laminated plates, with geometrically identical solid plates as reference. A coupled heat-transfer and thermo-mechanical finite element model was developed in MSC Marc using a composite Gaussian surface–volumetric moving heat source and temperature-dependent properties. The thermal solution was validated against near-weld thermal cycles and fusion geometry; mechanical predictions were evaluated by CMM distortion and residual-stress measurements. Both structures show comparable residual-stress magnitudes and spatial trends, indicating that residual stress is governed mainly by the local weld thermal gradient. In contrast, the laminated plate exhibits larger angular/bending distortion. Simulations show that, although the plastic-strain pattern is similar, the laminated plate develops higher peak plastic strain confined to a narrower band near the weld, with the transverse plastic strain dominating. Plastic strain–temperature paths reveal continued transverse plastic-strain accumulation during cooling with limited recovery, consistent with restraint redistribution induced by stiffness non-uniformity. An equivalent restraint–stiffness spring model explains this “narrower-but-stronger” plastic zone and links stiffness to yielding and residual plastic-strain magnitude, supporting distortion prediction and stiffness-informed control of welded laminated cooling plates.
- Open Access
Integrated Prediction of Gas Metal Arc Welding Multi-Layer Welding Heat Cycle, Ferrite Fraction, and Joint Hardness of X80 Pipeline Steel
X80 pipeline steel is widely used in oil and gas pipelines because of its excellent strength, toughness, and corrosion resistance. It is welded via gas metal arc welding (GMAW), risking high cold crack sensitivities. There is a certain relationship between the joint hardness and cold crack sensitivity of welded joints; thus, predicting the joint hardness is necessary. Considering the inefficiency of welding experiments and the complexity of welding parameters, we designed a set of processes from temperature field analysis to microstructure prediction and finally hardness prediction. Firstly, we calculated the thermal cycle curve during welding through multi-layer welding numerical simulation using the finite element method (FEM). Afterwards, BP neural networks were used to predict the cooling rates in the temperature interval that ferrite nuclears and grows. Introducing the cooling rates to the Leblond function, the ferrite fraction of the joint was given. Based on the predicted ferrite fraction, mapping relationships between joint hardness and the joint ferrite fraction were built using BP neural networks. The results shows that the error during phase fraction prediction is less than 8%, and during joint hardness prediction, it is less than 5%.
Open AccessIntegrated Prediction of Gas Metal Arc Welding Multi-Layer Welding Heat Cycle, Ferrite Fraction, and Joint Hardness of X80 Pipeline Steel
X80 pipeline steel is widely used in oil and gas pipelines because of its excellent strength, toughness, and corrosion resistance. It is welded via gas metal arc welding (GMAW), risking high cold crack sensitivities. There is a certain relationship between the joint hardness and cold crack sensitivity of welded joints; thus, predicting the joint hardness is necessary. Considering the inefficiency of welding experiments and the complexity of welding parameters, we designed a set of processes from temperature field analysis to microstructure prediction and finally hardness prediction. Firstly, we calculated the thermal cycle curve during welding through multi-layer welding numerical simulation using the finite element method (FEM). Afterwards, BP neural networks were used to predict the cooling rates in the temperature interval that ferrite nuclears and grows. Introducing the cooling rates to the Leblond function, the ferrite fraction of the joint was given. Based on the predicted ferrite fraction, mapping relationships between joint hardness and the joint ferrite fraction were built using BP neural networks. The results shows that the error during phase fraction prediction is less than 8%, and during joint hardness prediction, it is less than 5%.
- 4 September 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 915
Investigation on the moderately high-temperature tensile behavior of the laser powder bed fusion-fabricated 17-4 PH steel
- 4 September 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 915
Investigation on the moderately high-temperature tensile behavior of the laser powder bed fusion-fabricated 17-4 PH steel
- 8 July 2021
- Published by Wiley in Physica Status Solidi (b)
- Vol. 258 (10) , 2100123
Effects of Welding Parameter on Atom‐Scale Interfacial Diffusion Behavior of Al/Cu Dissimilar Friction Stir Welding
The partial weak bonding phenomenon induced by an unsuitable welding parameter often occurs at the joint interface of Al/Cu dissimilar friction stir welding (FSW). Diffusion time, temperature, and pressure are the main factors that affect the diffusion behavior at the interface. Therefore, molecular dynamics (MD) simulation is used to investigate the influence mechanism of these factors from the perspectives of diffusion thickness, total energy, and volume. The diffusion time and the temperature affect the diffusion thickness significantly, whereas external pressure has little impact. The variations of total energy and volume consist of two stages, which are caused by the combined effects of lattice transformation and atomic diffusion. The variation processes of total energy and volume are accelerated with the increase in temperature due to a higher diffusion velocity, and it is delayed by external pressure at a higher temperature because the lattice transformation is inhibited. These findings are beneficial to the choice of welding parameters in actual production.
- 8 July 2021
- Published by Wiley in Physica Status Solidi (b)
- Vol. 258 (10) , 2100123
Effects of Welding Parameter on Atom‐Scale Interfacial Diffusion Behavior of Al/Cu Dissimilar Friction Stir Welding
The partial weak bonding phenomenon induced by an unsuitable welding parameter often occurs at the joint interface of Al/Cu dissimilar friction stir welding (FSW). Diffusion time, temperature, and pressure are the main factors that affect the diffusion behavior at the interface. Therefore, molecular dynamics (MD) simulation is used to investigate the influence mechanism of these factors from the perspectives of diffusion thickness, total energy, and volume. The diffusion time and the temperature affect the diffusion thickness significantly, whereas external pressure has little impact. The variations of total energy and volume consist of two stages, which are caused by the combined effects of lattice transformation and atomic diffusion. The variation processes of total energy and volume are accelerated with the increase in temperature due to a higher diffusion velocity, and it is delayed by external pressure at a higher temperature because the lattice transformation is inhibited. These findings are beneficial to the choice of welding parameters in actual production.
- Open Access
Strength Calculation and Equal Load-Carrying-Capacity Design of an Undermatched HSLA Lap Joint under Out-of-Plane Bending
This work aimed to design an undermatched lap joint that has an equal load-carrying capacity (ELCC) with a traditional equalmatched joint under out-of-plane bending. A weld strength calculation method was proposed based on the similarity of a lap joint and a T joint, as shown using linear elastic finite element (FE) analysis, and then applied in the analysis of a lap joint and the design of an ELCC lap joint. A single lap joint of HQ785 steel was chosen for experimental verification. The bending force limit of the ELCC joint was 93.35% of the theoretical prediction and 96.90% of the traditional equalmatched joint. The results show that the weld strength calculation method and the ELCC design method are reasonable and feasible.
Open AccessStrength Calculation and Equal Load-Carrying-Capacity Design of an Undermatched HSLA Lap Joint under Out-of-Plane Bending
This work aimed to design an undermatched lap joint that has an equal load-carrying capacity (ELCC) with a traditional equalmatched joint under out-of-plane bending. A weld strength calculation method was proposed based on the similarity of a lap joint and a T joint, as shown using linear elastic finite element (FE) analysis, and then applied in the analysis of a lap joint and the design of an ELCC lap joint. A single lap joint of HQ785 steel was chosen for experimental verification. The bending force limit of the ELCC joint was 93.35% of the theoretical prediction and 96.90% of the traditional equalmatched joint. The results show that the weld strength calculation method and the ELCC design method are reasonable and feasible.
- 28 August 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (9) , 5886-5893
Solid-State Repair of Casting Defects in ZL210 Aluminum Alloy
- 28 August 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (9) , 5886-5893
Solid-State Repair of Casting Defects in ZL210 Aluminum Alloy
- 18 May 2020
- Published by Science China Press., Co. Ltd. in SCIENTIA SINICA Technologica
- Vol. 50 (7) , 957-963
Reconstructing a 3D map of longitudinal residual stress by combining the inherent strain theory and contour method
A new method for measuring three-dimensional (3D) residual stress by combining the contour method and the inherent strain theory is proposed. After measuring the fluctuation data of the cut planes caused by the release of stress, the inherent strain is obtained. The inherent strain is used to derive the 3D internal residual stresses. Comparing the results to numerical simulation and the small-hole method results proves the reliability of the method, the reliability of the contour method, and the inherent strain theory. Therefore, this new method can be widely applied to measure the 3D residual stress of materials in the future.
- 18 May 2020
- Published by Science China Press., Co. Ltd. in SCIENTIA SINICA Technologica
- Vol. 50 (7) , 957-963
Reconstructing a 3D map of longitudinal residual stress by combining the inherent strain theory and contour method
A new method for measuring three-dimensional (3D) residual stress by combining the contour method and the inherent strain theory is proposed. After measuring the fluctuation data of the cut planes caused by the release of stress, the inherent strain is obtained. The inherent strain is used to derive the 3D internal residual stresses. Comparing the results to numerical simulation and the small-hole method results proves the reliability of the method, the reliability of the contour method, and the inherent strain theory. Therefore, this new method can be widely applied to measure the 3D residual stress of materials in the future.
- Open Access
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 774 (1)
Equal Load Carrying Capacity Design of Butt Joints Based on Plastic Limit Loads
In order to reduce the weld size of weld joints designed based on equal load carrying capacity (ELCC) further, the shape of under-matching butt joints is designed with the parameter of plastic limit loads. The realization condition of ELCC is that the plastic limit loads of the weld equals to that of the base metal. Through analysing the tensile/bending load carrying capacity of weld zone, the weld shape was determined, and the method of tensile/bending ELCC design for butt joints is given. The ELCC joints are designed and their elastoplastic finite element analyses are carried out to verify their load carrying capacities. The tensile ELCC joint fractures at the base metal in the mode of overall yield fracture and its load carrying capacity reaches the tensile strength of the base metal. The load carrying capacity, deformability and stiffness of the bending ELCC joint are better than that of the base metal. The results indicate that the joints with acceptable size meet the requirements of ELCC, which is of great significance to the application of ELCC joints.
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 774 (1)
Open AccessEqual Load Carrying Capacity Design of Butt Joints Based on Plastic Limit Loads
In order to reduce the weld size of weld joints designed based on equal load carrying capacity (ELCC) further, the shape of under-matching butt joints is designed with the parameter of plastic limit loads. The realization condition of ELCC is that the plastic limit loads of the weld equals to that of the base metal. Through analysing the tensile/bending load carrying capacity of weld zone, the weld shape was determined, and the method of tensile/bending ELCC design for butt joints is given. The ELCC joints are designed and their elastoplastic finite element analyses are carried out to verify their load carrying capacities. The tensile ELCC joint fractures at the base metal in the mode of overall yield fracture and its load carrying capacity reaches the tensile strength of the base metal. The load carrying capacity, deformability and stiffness of the bending ELCC joint are better than that of the base metal. The results indicate that the joints with acceptable size meet the requirements of ELCC, which is of great significance to the application of ELCC joints.
- 6 February 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (11-12) , 5307-5315
Active-passive filling friction stir repairing of casting defects in ZL210 aluminum alloys
- 6 February 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (11-12) , 5307-5315
Active-passive filling friction stir repairing of casting defects in ZL210 aluminum alloys