Fang Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fang Han has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Chengcheng Wang
State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Chengkun Li
State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Xiaoqing Zhu
State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Zhibo Dong
State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Zhihang Zhang
State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2 shared publications - Han Wang
National Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
1 shared publication
Latest Publications
- Open Access
- 1 October 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (10) , 394
Angle-Dependent Inherent Strain in LPBF Overhang Structures: Modeling and Residual Stress Validation
Low-angle overhang structures in laser powder bed fusion (LPBF) experience strongly geometry-dependent thermal conditions because the underlying material progressively changes from consolidated solid to low-conductivity powder, which raises a fundamental question regarding the conventional use of a uniform inherent strain for efficient residual stress and distortion prediction. In this study, the dynamic inherent strain (DIS) method is employed to investigate the inherent strain behavior of LPBF overhang structures with different tilt-angles. The results reveal that after excluding the boundary-affected stages of the build, the representative inherent strain exhibits a systematic dependence on tilt-angle in both magnitude and tensor characteristics. Based on this angle dependence, compact angle-dependent expressions are established using trigonometric basis functions for engineering implementation. Comparisons with residual stress measurements at the experimentally investigated 30° and 90° geometries further indicate that angle-specific inherent strain assignment has a greater influence on the mechanical response toward the lower bound of the investigated angular range.
- 1 October 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (10) , 394
Open AccessAngle-Dependent Inherent Strain in LPBF Overhang Structures: Modeling and Residual Stress Validation
Low-angle overhang structures in laser powder bed fusion (LPBF) experience strongly geometry-dependent thermal conditions because the underlying material progressively changes from consolidated solid to low-conductivity powder, which raises a fundamental question regarding the conventional use of a uniform inherent strain for efficient residual stress and distortion prediction. In this study, the dynamic inherent strain (DIS) method is employed to investigate the inherent strain behavior of LPBF overhang structures with different tilt-angles. The results reveal that after excluding the boundary-affected stages of the build, the representative inherent strain exhibits a systematic dependence on tilt-angle in both magnitude and tensor characteristics. Based on this angle dependence, compact angle-dependent expressions are established using trigonometric basis functions for engineering implementation. Comparisons with residual stress measurements at the experimentally investigated 30° and 90° geometries further indicate that angle-specific inherent strain assignment has a greater influence on the mechanical response toward the lower bound of the investigated angular range.
- Open Access
Heat Transfer and Thermo-Mechanical Analysis of Plastic-Strain Evolution in Laser-Welded Thin-Walled Laminated Cooling Plates with Non-Uniform Stiffness
Thin-walled laminated cooling plates integrate internal channels and pin-fin cores, producing reduced and spatially non-uniform stiffness that changes welding restraint and distortion. This study investigates stiffness-controlled plastic-strain evolution in laser butt welding of GH3230 laminated plates, with geometrically identical solid plates as reference. A coupled heat-transfer and thermo-mechanical finite element model was developed in MSC Marc using a composite Gaussian surface–volumetric moving heat source and temperature-dependent properties. The thermal solution was validated against near-weld thermal cycles and fusion geometry; mechanical predictions were evaluated by CMM distortion and residual-stress measurements. Both structures show comparable residual-stress magnitudes and spatial trends, indicating that residual stress is governed mainly by the local weld thermal gradient. In contrast, the laminated plate exhibits larger angular/bending distortion. Simulations show that, although the plastic-strain pattern is similar, the laminated plate develops higher peak plastic strain confined to a narrower band near the weld, with the transverse plastic strain dominating. Plastic strain–temperature paths reveal continued transverse plastic-strain accumulation during cooling with limited recovery, consistent with restraint redistribution induced by stiffness non-uniformity. An equivalent restraint–stiffness spring model explains this “narrower-but-stronger” plastic zone and links stiffness to yielding and residual plastic-strain magnitude, supporting distortion prediction and stiffness-informed control of welded laminated cooling plates.
Open AccessHeat Transfer and Thermo-Mechanical Analysis of Plastic-Strain Evolution in Laser-Welded Thin-Walled Laminated Cooling Plates with Non-Uniform Stiffness
Thin-walled laminated cooling plates integrate internal channels and pin-fin cores, producing reduced and spatially non-uniform stiffness that changes welding restraint and distortion. This study investigates stiffness-controlled plastic-strain evolution in laser butt welding of GH3230 laminated plates, with geometrically identical solid plates as reference. A coupled heat-transfer and thermo-mechanical finite element model was developed in MSC Marc using a composite Gaussian surface–volumetric moving heat source and temperature-dependent properties. The thermal solution was validated against near-weld thermal cycles and fusion geometry; mechanical predictions were evaluated by CMM distortion and residual-stress measurements. Both structures show comparable residual-stress magnitudes and spatial trends, indicating that residual stress is governed mainly by the local weld thermal gradient. In contrast, the laminated plate exhibits larger angular/bending distortion. Simulations show that, although the plastic-strain pattern is similar, the laminated plate develops higher peak plastic strain confined to a narrower band near the weld, with the transverse plastic strain dominating. Plastic strain–temperature paths reveal continued transverse plastic-strain accumulation during cooling with limited recovery, consistent with restraint redistribution induced by stiffness non-uniformity. An equivalent restraint–stiffness spring model explains this “narrower-but-stronger” plastic zone and links stiffness to yielding and residual plastic-strain magnitude, supporting distortion prediction and stiffness-informed control of welded laminated cooling plates.