Chenchen Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Chenchen Zhao has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Ming Cheng
Southeast University
5 shared publications - Yubin Wang
College of New Energy, China University of Petroleum, QingDao, China
4 shared publications - Wei Hua
Southeast University
3 shared publications - Jiawei Zhou
School of Electrical Engineering, Southeast University, Nanjing, China
2 shared publications - Wenfei Yu
School of Electrical Engineering, Southeast University, Nanjing 210096, China
2 shared publications - Xianglin Li
Qingdao University
2 shared publications
Latest Publications
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (1) , 264-278
Exploration of Rotor Topology Evolution Mechanism in the Stator-PM Machines
During the optimization of rotor configurations in the flux-switching permanent magnet (FSPM) machine, the contradiction between the pulsating torque suppression and the average torque improvement is a challenging aspect to be addressed. Accompanied by it is the absence of theoretical guidance on rotor design according to torque performance requirements. To address them, by virtue of general airgap field modulation theory (GAFMT), this paper focuses on investigating rotor topology evolution mechanisms that is not only applicable to FSPM machine, but also to flux-reversal PM (FRPM) machine and doubly-salient PM (DSPM) machine. The study proceeds with an analysis of impacts of PM placements on the rotor configurations in 12-stator-slot/10-rotor-pole stator-PM machines. Subsequently, a two-dimensional fast Fourier transformation (2D FFT) is employed to elucidate the trade-off between the increase of average torque and the decrease of pulsating torque. Thirdly, the concept of amplitude modulation is introduced, and under its guidance, two rotor configurations are designed according to their respective objective functions. Multiobjective optimization (MOP) is then applied to enhance the torque performance and evaluate the effectiveness of rotor topologies. Finally, the rotor topology evaluation mechanism of stator-PM machines is verified through finite element analysis (FEA) and experimental results, specifically in the case of FSPM machines.
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (1) , 264-278
Exploration of Rotor Topology Evolution Mechanism in the Stator-PM Machines
During the optimization of rotor configurations in the flux-switching permanent magnet (FSPM) machine, the contradiction between the pulsating torque suppression and the average torque improvement is a challenging aspect to be addressed. Accompanied by it is the absence of theoretical guidance on rotor design according to torque performance requirements. To address them, by virtue of general airgap field modulation theory (GAFMT), this paper focuses on investigating rotor topology evolution mechanisms that is not only applicable to FSPM machine, but also to flux-reversal PM (FRPM) machine and doubly-salient PM (DSPM) machine. The study proceeds with an analysis of impacts of PM placements on the rotor configurations in 12-stator-slot/10-rotor-pole stator-PM machines. Subsequently, a two-dimensional fast Fourier transformation (2D FFT) is employed to elucidate the trade-off between the increase of average torque and the decrease of pulsating torque. Thirdly, the concept of amplitude modulation is introduced, and under its guidance, two rotor configurations are designed according to their respective objective functions. Multiobjective optimization (MOP) is then applied to enhance the torque performance and evaluate the effectiveness of rotor topologies. Finally, the rotor topology evaluation mechanism of stator-PM machines is verified through finite element analysis (FEA) and experimental results, specifically in the case of FSPM machines.
- 18 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 2088-2096
Analytical Method of Stator Modal Analysis for Stator-Permanent Magnet Machines
This paper investigates the stator modal modes in stator-permanent magnet (PM) machines. Flux-reversal PM (FRPM) machine and flux-switching PM (FSPM) machine are taken as examples to investigate the different influences of PMs on the stator modal modes. Lagrange’s equations and Rayleigh-Ritz method are combined in the proposed analytical modal analysis method. Based on the different influences brought by the PMs, the stators in stator-PM machines are analyzed correspondingly. Meanwhile, composite material theory is also introduced to the teeth remodeling and the subsequent modification of isotropic material properties. The modal experiments of stators in different stator-PM machines are carried out and validate the feasibility of the proposed analytical modal analysis method of stator modal modes. The analytical modal analysis of the whole prototype is also carried out and compared to the experimental results, which proves the credibility of the proposed model.
- 18 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 2088-2096
Analytical Method of Stator Modal Analysis for Stator-Permanent Magnet Machines
This paper investigates the stator modal modes in stator-permanent magnet (PM) machines. Flux-reversal PM (FRPM) machine and flux-switching PM (FSPM) machine are taken as examples to investigate the different influences of PMs on the stator modal modes. Lagrange’s equations and Rayleigh-Ritz method are combined in the proposed analytical modal analysis method. Based on the different influences brought by the PMs, the stators in stator-PM machines are analyzed correspondingly. Meanwhile, composite material theory is also introduced to the teeth remodeling and the subsequent modification of isotropic material properties. The modal experiments of stators in different stator-PM machines are carried out and validate the feasibility of the proposed analytical modal analysis method of stator modal modes. The analytical modal analysis of the whole prototype is also carried out and compared to the experimental results, which proves the credibility of the proposed model.
- 23 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (10) , 11888-11897
Mechanism and Characteristics of Cogging Torque in Surface-Mounted PMSM: A General Airgap Field Modulation Theory Approach
In this article, the surface-mounted permanent magnet machine is regarded as a salient pole reluctance machine to take into account the effect of stator teeth. The field modulation behavior of the magnetizing field is firstly introduced, and the field model is then derived using the general airgap field modulation theory (GAFMT). The properties of the modulated field harmonics are explored based on the proposed field model. Subsequently, a general cogging torque model based on the virtual work method and the GAFMT is proposed to describe the relationship between the field harmonics and the cogging torque. On this basis, the mechanism of the cogging torque is studied, its frequency, effective field harmonics, and the contribution of each harmonic are revealed. The proposed model is then validated by comparing its results with those obtained from the Maxwell Stress Tensor method and the finite-element analysis, and a good agreement is observed, demonstrating the effectiveness of the proposed model. Furthermore, the experimental results also confirm the effectiveness of the proposed model.
- 23 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (10) , 11888-11897
Mechanism and Characteristics of Cogging Torque in Surface-Mounted PMSM: A General Airgap Field Modulation Theory Approach
In this article, the surface-mounted permanent magnet machine is regarded as a salient pole reluctance machine to take into account the effect of stator teeth. The field modulation behavior of the magnetizing field is firstly introduced, and the field model is then derived using the general airgap field modulation theory (GAFMT). The properties of the modulated field harmonics are explored based on the proposed field model. Subsequently, a general cogging torque model based on the virtual work method and the GAFMT is proposed to describe the relationship between the field harmonics and the cogging torque. On this basis, the mechanism of the cogging torque is studied, its frequency, effective field harmonics, and the contribution of each harmonic are revealed. The proposed model is then validated by comparing its results with those obtained from the Maxwell Stress Tensor method and the finite-element analysis, and a good agreement is observed, demonstrating the effectiveness of the proposed model. Furthermore, the experimental results also confirm the effectiveness of the proposed model.
- 3 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 38 (2) , 1433-1441
A Linear Hybrid Model for Analytical Magnetic Field Analysis in Flux-Switching Permanent-Magnet Machine
A hybrid model for the flux-switching permanent-magnet (FSPM) machine is proposed in this paper. In this hybrid model, the air-gap magnetic field in FSPM machine is investigated from the perspective of the stator modulation effect and rotor modulation effect. The stator modulation is discussed from the perspective of equivalent air-gap in the stator slots and permanent-magnets (PMs). The rotor modulation effect is divided to two aspects, namely the effect on the magnetomotive force (MMF) and the effect on stator modulation effect. Different from the conventional model where the stator modulation effect and the rotor modulation are independent of each other, stator modulation effect in the proposed model is coupled with the rotor modulation effect by the minimal reluctance principle. Therefore, MMF and the stator modulation effect in FSPM machine become susceptible to rotor positions with the influence of the rotor modulation effect. Air-gap flux density in FSPM machine is calculated by this hybrid model and compared with those by conventional model and finite element analysis (FEA). Finally, the effectiveness of the proposed hybrid model is validated by comparison of the electromotive force with FEA and experimental results.
- 3 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 38 (2) , 1433-1441
A Linear Hybrid Model for Analytical Magnetic Field Analysis in Flux-Switching Permanent-Magnet Machine
A hybrid model for the flux-switching permanent-magnet (FSPM) machine is proposed in this paper. In this hybrid model, the air-gap magnetic field in FSPM machine is investigated from the perspective of the stator modulation effect and rotor modulation effect. The stator modulation is discussed from the perspective of equivalent air-gap in the stator slots and permanent-magnets (PMs). The rotor modulation effect is divided to two aspects, namely the effect on the magnetomotive force (MMF) and the effect on stator modulation effect. Different from the conventional model where the stator modulation effect and the rotor modulation are independent of each other, stator modulation effect in the proposed model is coupled with the rotor modulation effect by the minimal reluctance principle. Therefore, MMF and the stator modulation effect in FSPM machine become susceptible to rotor positions with the influence of the rotor modulation effect. Air-gap flux density in FSPM machine is calculated by this hybrid model and compared with those by conventional model and finite element analysis (FEA). Finally, the effectiveness of the proposed hybrid model is validated by comparison of the electromotive force with FEA and experimental results.
- 14 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (7) , 6645-6656
Iterative Learning Based Torque Ripple Suppression of Flux-Modulation Double-Stator Machine
Due to the double-layer airgap configuration, the even-order harmonic components exist in the phase back electromotive force (EMF) of flux-modulation electrically excitation double-stator synchronous machine (FMEE-DSM), thus resulting in relatively high torque ripples. To promptly and effectively suppress these torque ripples, this article proposes and implements a second-order iterative learning control (ILC) strategy to minimize the main harmonic torque components based on the periodically repetitive characteristic of torque ripples in the FMEE-DSM. Via harmonic analysis on the torque ripples caused by the cogging torque and the nonsinusoidal induced EMFs, the dominative harmonic component, namely, the seventh-order component, can be precisely identified and then involved in the proposed ILC for torque ripple suppression. To verify the feasibility of proposed control strategy, a test bench of the FMEE-DSM control system was built based on dSPACE 1103. Accordingly, both the static and dynamic performances of the FMEE-DSM were investigated under the conditions of no-load and rated load. The theoretical analysis, computer simulation, and hardware experimentation are given to verify the proposed second-order ILC.
- 14 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (7) , 6645-6656
Iterative Learning Based Torque Ripple Suppression of Flux-Modulation Double-Stator Machine
Due to the double-layer airgap configuration, the even-order harmonic components exist in the phase back electromotive force (EMF) of flux-modulation electrically excitation double-stator synchronous machine (FMEE-DSM), thus resulting in relatively high torque ripples. To promptly and effectively suppress these torque ripples, this article proposes and implements a second-order iterative learning control (ILC) strategy to minimize the main harmonic torque components based on the periodically repetitive characteristic of torque ripples in the FMEE-DSM. Via harmonic analysis on the torque ripples caused by the cogging torque and the nonsinusoidal induced EMFs, the dominative harmonic component, namely, the seventh-order component, can be precisely identified and then involved in the proposed ILC for torque ripple suppression. To verify the feasibility of proposed control strategy, a test bench of the FMEE-DSM control system was built based on dSPACE 1103. Accordingly, both the static and dynamic performances of the FMEE-DSM were investigated under the conditions of no-load and rated load. The theoretical analysis, computer simulation, and hardware experimentation are given to verify the proposed second-order ILC.
- 28 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 36 (4) , 3395-3404
Vibration and Noise Analysis of Flux-Modulation Double Stator Electrical-Excitation Synchronous Machine
This paper studies the vibration and noise analysis of flux-modulation double-stator electrical-excitation synchronous machine (FM-DSEESM) in both no-load mode and on-load mode by using the mode superposition method. First, the theoretical excitations of vibration and noise, namely the radial electromagnetic force harmonics, are deduced and classified by their sources. Second, the finite element analyses (FEA) of these radial electromagnetic force harmonics are analyzed via Fourier decomposition and compared to their theoretical results for validation. Third, to perform the vibration and noise analysis, the modal test is conducted, and the modal FEA model is established based on the tested modal results. Also, the radial electromagnetic forces are coupled with the modal FEA model to conduct the vibration and noise analysis, and the responses of sound power levels in A-weighting are calculated. By using the modal participating factors, the main contributing modes are determined in the vibration and noise responses.
- 28 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 36 (4) , 3395-3404
Vibration and Noise Analysis of Flux-Modulation Double Stator Electrical-Excitation Synchronous Machine
This paper studies the vibration and noise analysis of flux-modulation double-stator electrical-excitation synchronous machine (FM-DSEESM) in both no-load mode and on-load mode by using the mode superposition method. First, the theoretical excitations of vibration and noise, namely the radial electromagnetic force harmonics, are deduced and classified by their sources. Second, the finite element analyses (FEA) of these radial electromagnetic force harmonics are analyzed via Fourier decomposition and compared to their theoretical results for validation. Third, to perform the vibration and noise analysis, the modal test is conducted, and the modal FEA model is established based on the tested modal results. Also, the radial electromagnetic forces are coupled with the modal FEA model to conduct the vibration and noise analysis, and the responses of sound power levels in A-weighting are calculated. By using the modal participating factors, the main contributing modes are determined in the vibration and noise responses.
- Open Access
Vibroacoustic Prediction of a High-Temperature Superconducting Field-Modulation Double-Stator Machine with Stationary Seal
This paper predicted the vibroacoustic regularity of a high temperature superconducting (HTS) field-modulation double-stator (HTS-FMDS) machine with stationary seal for low-speed and direct-drive applications. The originality of this paper lies in that the spatial order and angular velocity of electromagnetic-force density of the HTS-FMDS machine were derived by using the analytical method. Moreover, the validity of the analytical solutions was verified by the finite element analysis (FEA) results. Then, the modal shapes and frequencies of the outer stator were obtained by using multiphysics coupling simulation. By transferring the electromagnetic force to the stator structural model, the regularity of electromagnetic vibration and noise of the HTS-FMDS machine were revealed.
Open AccessVibroacoustic Prediction of a High-Temperature Superconducting Field-Modulation Double-Stator Machine with Stationary Seal
This paper predicted the vibroacoustic regularity of a high temperature superconducting (HTS) field-modulation double-stator (HTS-FMDS) machine with stationary seal for low-speed and direct-drive applications. The originality of this paper lies in that the spatial order and angular velocity of electromagnetic-force density of the HTS-FMDS machine were derived by using the analytical method. Moreover, the validity of the analytical solutions was verified by the finite element analysis (FEA) results. Then, the modal shapes and frequencies of the outer stator were obtained by using multiphysics coupling simulation. By transferring the electromagnetic force to the stator structural model, the regularity of electromagnetic vibration and noise of the HTS-FMDS machine were revealed.