C. L. Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
C. L. Wu has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Song Zhang
School of Materials Science and Engineering, Shenyang University of Technology, Shenyang, China
7 shared publications C. H. Zhang
School of Materials Science and Engineering, Shenyang University of Technology, Shenyang, PR China
4 shared publications- Chun Hua Zhang
School of Materials Science and Engineering, Shenyang University of Technology, Shenyang, People’s Republic of China
4 shared publications J. Chen
Shenyang Dalu Laser Technology CO., LTD, Shenyang, People’s Republic of China
3 shared publicationsX. L. Bai
Shenyang Donfon Titanium Industry CO., LTD, Shenyang, People’s Republic of China
3 shared publicationsX. Y. Sun
Shenyang Dalu Laser Technology CO., LTD, Shenyang, People’s Republic of China
3 shared publications
Latest Publications
- Open Access
Modulating Heat Input to Optimize Corrosion Resistance of Nickel–Aluminum Bronze Manufactured by Cold Metal Transfer Additive Manufacturing
The influence of heat input (HI) on the microstructure, microhardness, electrochemical corrosion performance of cold metal transfer additively manufactured (CMTAM) nickel–aluminum bronze alloys was investigated. The nickel–aluminum bronze exhibited an α-Cu austenite matrix with minor γ2-Cu9Al4 and κ phases. As HI increased, the microstructure coarsened progressively. Electron backscatter diffraction (EBSD) analysis revealed that with increasing HI, the grain size gradually increased and the Schmid factor increased. Consequently, the microhardness declined from 198.3 HV to 171.7 HV. The decrease in microhardness with increasing heat input is primarily attributed to the grain coarsening and the coarsening and uneven distribution of the κ phase. As the heat input (HI) increased from 243.8 J/mm to 644.7 J/mm, the corrosion current density rose significantly from 2.56 ± 0.04 μA/cm2 to 7.52 ± 0.07 μA/cm2. This result indicates a marked deterioration in the material’s corrosion resistance. This phenomenon can be attributed to the grain coarsening and the distribution of Al solute within the microstructure. The CMTAM nickel–aluminum bronze alloys hold significant potential for enhancing the reliability and long-term protection of marine engineering equipment.
Open AccessModulating Heat Input to Optimize Corrosion Resistance of Nickel–Aluminum Bronze Manufactured by Cold Metal Transfer Additive Manufacturing
The influence of heat input (HI) on the microstructure, microhardness, electrochemical corrosion performance of cold metal transfer additively manufactured (CMTAM) nickel–aluminum bronze alloys was investigated. The nickel–aluminum bronze exhibited an α-Cu austenite matrix with minor γ2-Cu9Al4 and κ phases. As HI increased, the microstructure coarsened progressively. Electron backscatter diffraction (EBSD) analysis revealed that with increasing HI, the grain size gradually increased and the Schmid factor increased. Consequently, the microhardness declined from 198.3 HV to 171.7 HV. The decrease in microhardness with increasing heat input is primarily attributed to the grain coarsening and the coarsening and uneven distribution of the κ phase. As the heat input (HI) increased from 243.8 J/mm to 644.7 J/mm, the corrosion current density rose significantly from 2.56 ± 0.04 μA/cm2 to 7.52 ± 0.07 μA/cm2. This result indicates a marked deterioration in the material’s corrosion resistance. This phenomenon can be attributed to the grain coarsening and the distribution of Al solute within the microstructure. The CMTAM nickel–aluminum bronze alloys hold significant potential for enhancing the reliability and long-term protection of marine engineering equipment.
- 10 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (18) , 19881-19894
Study on Microstructure and Cavitation Resistance of Fe-Based and Ni-Based Alloy Coatings by Plasma Transfer Arc Welding
- 10 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (18) , 19881-19894
Study on Microstructure and Cavitation Resistance of Fe-Based and Ni-Based Alloy Coatings by Plasma Transfer Arc Welding
- 24 January 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (18) , 20102-20116
Microstructure, Wear and Corrosion Performance of Cold Metal Transfer Additive Manufactured (Ni, Ti)-Modified Nickel Aluminum Bronze Alloy
- 24 January 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (18) , 20102-20116
Microstructure, Wear and Corrosion Performance of Cold Metal Transfer Additive Manufactured (Ni, Ti)-Modified Nickel Aluminum Bronze Alloy
- 16 October 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (22) , 12398-12412
Comparative Study on the Microstructure, Wear Behavior, and Corrosion Performance of Iron-Based and Cobalt-Based Coatings Fabricated by Laser Cladding
- 16 October 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (22) , 12398-12412
Comparative Study on the Microstructure, Wear Behavior, and Corrosion Performance of Iron-Based and Cobalt-Based Coatings Fabricated by Laser Cladding
- 1 September 2023
- Published by SAGE Publications in Materials Science and Technology
- Vol. 39 (13) , 1555-1565
Microstructure and corrosion behaviour of WC-Co coating fabricated by plasma arc welding
The WC-Co composite coating was prepared on SS 316L by plasma arc welding technology. The microstructure, phase composition, and microhardness of the WC-Co composite coating were thoroughly studied. The corrosion behaviour including electrochemical corrosion, cavitation erosion, and erosion corrosion was tested. The results showed that the WC-Co coating exhibited a good metallurgical bond with the substrate. The average microhardness of the WC-Co coating reached 1785 HV, which was 9.4 times that of the SS 316L. The corrosion current density of the WC-Co composite coating was one order of magnitude lower than that of the substrate. Meanwhile, the cumulative mass loss of cavitation erosion and erosion corrosion of the WC-Co composite coating was much lower than that of the SS 316L.
- 1 September 2023
- Published by SAGE Publications in Materials Science and Technology
- Vol. 39 (13) , 1555-1565
Microstructure and corrosion behaviour of WC-Co coating fabricated by plasma arc welding
The WC-Co composite coating was prepared on SS 316L by plasma arc welding technology. The microstructure, phase composition, and microhardness of the WC-Co composite coating were thoroughly studied. The corrosion behaviour including electrochemical corrosion, cavitation erosion, and erosion corrosion was tested. The results showed that the WC-Co coating exhibited a good metallurgical bond with the substrate. The average microhardness of the WC-Co coating reached 1785 HV, which was 9.4 times that of the SS 316L. The corrosion current density of the WC-Co composite coating was one order of magnitude lower than that of the substrate. Meanwhile, the cumulative mass loss of cavitation erosion and erosion corrosion of the WC-Co composite coating was much lower than that of the SS 316L.
- 20 June 2023
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 32 (7) , 2236-2249
Microstructural Evolution and Properties of Novel Ferritic Stainless Steel–Mox Prepared by Laser Melting Deposition
- 20 June 2023
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 32 (7) , 2236-2249
Microstructural Evolution and Properties of Novel Ferritic Stainless Steel–Mox Prepared by Laser Melting Deposition
- Open Access
Preparation and Characterization of In Situ Carbide Particle Reinforced Fe-Based Gradient Materials by Laser Melt Deposition
To obtain the wear-resistant camshaft with surface rigidity and core toughness and improve the service life of camshaft, wear-resistant Fe-based alloy gradient material was prepared by laser melt deposition. The traditional camshaft was forged by 12CrNi2V. In this paper, four types of wear-resistant Fe-based powders were designed by introducing various content of Cr3C2 and V-rich Fe-based alloy (FeV50) into stainless steel powder. The results showed that the gradient materials formed a satisfactory metallurgical bond. The composition of the phases was mainly composed of α-Fe, Cr23C6, and V2C phases. The increasing of Cr3C2 and FeV50 led to transform V2C into the V8C7. The microstructures were mainly cellular dendrite and intergranular structure. Due to the addition of Cr3C2 and FeV50, the average microhardness and wear resistance of gradient materials were significantly better than that of 12CrNi2V. The sample with 8% V had the highest microhardness of 853 ± 18 HV, which was 2.6 times higher than that of 12CrNi2V. The sample with 6% V had the best wear resistance, which was 21 times greater than that of 12CrNi2V.
Open AccessPreparation and Characterization of In Situ Carbide Particle Reinforced Fe-Based Gradient Materials by Laser Melt Deposition
To obtain the wear-resistant camshaft with surface rigidity and core toughness and improve the service life of camshaft, wear-resistant Fe-based alloy gradient material was prepared by laser melt deposition. The traditional camshaft was forged by 12CrNi2V. In this paper, four types of wear-resistant Fe-based powders were designed by introducing various content of Cr3C2 and V-rich Fe-based alloy (FeV50) into stainless steel powder. The results showed that the gradient materials formed a satisfactory metallurgical bond. The composition of the phases was mainly composed of α-Fe, Cr23C6, and V2C phases. The increasing of Cr3C2 and FeV50 led to transform V2C into the V8C7. The microstructures were mainly cellular dendrite and intergranular structure. Due to the addition of Cr3C2 and FeV50, the average microhardness and wear resistance of gradient materials were significantly better than that of 12CrNi2V. The sample with 8% V had the highest microhardness of 853 ± 18 HV, which was 2.6 times higher than that of 12CrNi2V. The sample with 6% V had the best wear resistance, which was 21 times greater than that of 12CrNi2V.
- Open Access
Effects of V and Cr on Laser Cladded Fe-Based Coatings
Fe-based coatings with high V and Cr content were obtained by laser cladding using Fe-based powder with different Cr3C2 and FeV50 content. The results showed that Fe-based coatings were uniform and dense. The constituent phases were mainly composed of α-Fe solid solution with the increase of Cr3C2 and FeV50, γ-Fe and V8C7 phases were achieved. The microstructure of the coatings exhibited a typical dendrite structure. The concentration of C, V and Cr were saturated in dendritic areas, and the other alloying elements were mainly dissolved in the interdendritic areas. The hardness and wear resistance of Fe-based coatings were enhanced with the Cr3C2 and FeV50 addition. The specimen with 15% Cr3C2 and 16% FeV50 had the highest hardness of 66.1 ± 0.6 HRC, which was 1.05 times higher than the sample with 4.5% Cr3C2 and 5% FeV50, and the wear resistance of the former was three times greater than the latter.
Open AccessEffects of V and Cr on Laser Cladded Fe-Based Coatings
Fe-based coatings with high V and Cr content were obtained by laser cladding using Fe-based powder with different Cr3C2 and FeV50 content. The results showed that Fe-based coatings were uniform and dense. The constituent phases were mainly composed of α-Fe solid solution with the increase of Cr3C2 and FeV50, γ-Fe and V8C7 phases were achieved. The microstructure of the coatings exhibited a typical dendrite structure. The concentration of C, V and Cr were saturated in dendritic areas, and the other alloying elements were mainly dissolved in the interdendritic areas. The hardness and wear resistance of Fe-based coatings were enhanced with the Cr3C2 and FeV50 addition. The specimen with 15% Cr3C2 and 16% FeV50 had the highest hardness of 66.1 ± 0.6 HRC, which was 1.05 times higher than the sample with 4.5% Cr3C2 and 5% FeV50, and the wear resistance of the former was three times greater than the latter.