Peiyu Yan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Peiyu Yan has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Qiang Wang
Department of Civil Engineering, Tsinghua University, Beijing, 100084, China
7 shared publications - Fanghui Han
School of Future Cities, University of Science and Technology Beijing, Beijing, China
3 shared publications - Jinbo Yang
Beijing University of Technology
3 shared publications Song Han
Tsinghua University
3 shared publicationsYu Liu
China Construction First Group Construction and Development Co., Ltd, Beijing, China
3 shared publications- Zengqi Zhang
State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing 100083, China
3 shared publications
Latest Publications
- Open Access
Effects of Mineral Admixtures on the Evolution of Static Yield Stress of Different Composite Pastes
The effects of different mineral admixtures on the evolution of static yield stress of common composite cementitious material paste and ultra-high-performance concrete (UHPC)-based paste were investigated. The results show that there are obvious differences in the role of mineral admixtures in the common paste and the UHPC-based paste. Adding mineral admixtures can change the initial static yield stress of the paste by affecting the particle size, particle shape and the charged particles. The addition of mineral admixtures with small particle size such as silica fume and ultrafine slag can increase the initial static yield stress of common paste but reduce that of UHPC-based paste. Adding mineral admixtures changes the evolution of static yield stress of the paste by affecting the particle spacing and the formation and growth rate of hydration products. In turn, the addition of ultrafine slag or silica fume increases the growth of the static yield stress of common paste. Adding slag, fly ash or fly ash microbeads successively reduces the static yield stress of common paste at the later stage. Affected by the content of PCE, the static yield stress of UHPC-based paste containing fly ash microbeads, slag, ultrafine slag and fly ash increases sequentially compared with the blank group at the later stage. The effect of silica fume with different dosages on the evolution of static yield stress of UHPC-based paste is significantly different.
Open AccessEffects of Mineral Admixtures on the Evolution of Static Yield Stress of Different Composite Pastes
The effects of different mineral admixtures on the evolution of static yield stress of common composite cementitious material paste and ultra-high-performance concrete (UHPC)-based paste were investigated. The results show that there are obvious differences in the role of mineral admixtures in the common paste and the UHPC-based paste. Adding mineral admixtures can change the initial static yield stress of the paste by affecting the particle size, particle shape and the charged particles. The addition of mineral admixtures with small particle size such as silica fume and ultrafine slag can increase the initial static yield stress of common paste but reduce that of UHPC-based paste. Adding mineral admixtures changes the evolution of static yield stress of the paste by affecting the particle spacing and the formation and growth rate of hydration products. In turn, the addition of ultrafine slag or silica fume increases the growth of the static yield stress of common paste. Adding slag, fly ash or fly ash microbeads successively reduces the static yield stress of common paste at the later stage. Affected by the content of PCE, the static yield stress of UHPC-based paste containing fly ash microbeads, slag, ultrafine slag and fly ash increases sequentially compared with the blank group at the later stage. The effect of silica fume with different dosages on the evolution of static yield stress of UHPC-based paste is significantly different.
- Open Access
Which Is an Appropriate Quadratic Rheological Model of Fresh Paste, the Modified Bingham Model or the Parabolic Model?
The physical meaning and calculating process of the rheological parameters of two nonlinear rheological models, the parabolic model and the modified Bingham model, were compared. The fluidity test and a rheological experiment on cementitious materials were performed. The Couette inverse problem is a key issue in measuring and solving the rheological parameters of fresh cementitious materials. The solution of the Couette inverse problem based on the modified Bingham model is discontinuous when the coefficient of the quadratic term is equal to zero, resulting in a large deviation between the fitting curve and the rheological experimental data. The credibility of the rheological parameters of the pastes calculated based on the modified Bingham model is low. The formulas for calculating yield stress, fiducial differential viscosity and the degree of shear thickening or shear thinning of the parabolic model have been developed. The credibility of the rheological parameters of the pastes calculated based on the parabolic model is high. The flow performance of the paste can be clearly characterized by the rheological parameters calculated with the parabolic model.
Open AccessWhich Is an Appropriate Quadratic Rheological Model of Fresh Paste, the Modified Bingham Model or the Parabolic Model?
The physical meaning and calculating process of the rheological parameters of two nonlinear rheological models, the parabolic model and the modified Bingham model, were compared. The fluidity test and a rheological experiment on cementitious materials were performed. The Couette inverse problem is a key issue in measuring and solving the rheological parameters of fresh cementitious materials. The solution of the Couette inverse problem based on the modified Bingham model is discontinuous when the coefficient of the quadratic term is equal to zero, resulting in a large deviation between the fitting curve and the rheological experimental data. The credibility of the rheological parameters of the pastes calculated based on the modified Bingham model is low. The formulas for calculating yield stress, fiducial differential viscosity and the degree of shear thickening or shear thinning of the parabolic model have been developed. The credibility of the rheological parameters of the pastes calculated based on the parabolic model is high. The flow performance of the paste can be clearly characterized by the rheological parameters calculated with the parabolic model.
- Open Access
- 9 November 2022
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 20 (11) , 653-662
Investigation on the Unusual Hydration and Hardening Process of a Portland Cement with Low Alkali Sulfate Content
The infrequent setting behavior and hydration process of a Portland cement with very low alkali content were concerned. Gypsum and K2SO4 with different quantities and ratios were added into cement to adjust its sulfate and alkali content. The setting time and compressive strength of cements were tested, the hydration process and hydrates of cements were investigated by isothermal calorimetry, non-evaporable water content and XRD. The results show that gypsum addition is incapable of delaying the quick initial setting of the cement clinker. A moderate substitution of gypsum by K2SO4 in same reasonable sulfate content can promote the dissolution of gypsum, suppress the formation of h-AFm, and therefore prolong the initial setting time of the cement. Moreover, the Portland cement clinker shows a very hysteretic hydration exothermic process, accompanying with a hysteretic finial setting and a weak mechanical property in early age. An appropriate dosage of gypsum can promote the hydration of the cement and result in a reasonable final setting behavior and satisfactory strength development. The modification of gypsum on the properties of cement is influenced by its alkali content. The measures which could accelerate the sulfate-supply in cement is necessary to acquire a favorable hardening property when the cement with low alkali content is used in projects.
- 9 November 2022
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 20 (11) , 653-662
Open AccessInvestigation on the Unusual Hydration and Hardening Process of a Portland Cement with Low Alkali Sulfate Content
The infrequent setting behavior and hydration process of a Portland cement with very low alkali content were concerned. Gypsum and K2SO4 with different quantities and ratios were added into cement to adjust its sulfate and alkali content. The setting time and compressive strength of cements were tested, the hydration process and hydrates of cements were investigated by isothermal calorimetry, non-evaporable water content and XRD. The results show that gypsum addition is incapable of delaying the quick initial setting of the cement clinker. A moderate substitution of gypsum by K2SO4 in same reasonable sulfate content can promote the dissolution of gypsum, suppress the formation of h-AFm, and therefore prolong the initial setting time of the cement. Moreover, the Portland cement clinker shows a very hysteretic hydration exothermic process, accompanying with a hysteretic finial setting and a weak mechanical property in early age. An appropriate dosage of gypsum can promote the hydration of the cement and result in a reasonable final setting behavior and satisfactory strength development. The modification of gypsum on the properties of cement is influenced by its alkali content. The measures which could accelerate the sulfate-supply in cement is necessary to acquire a favorable hardening property when the cement with low alkali content is used in projects.
- 2 November 2022
- Published by Taylor & Francis in Journal of Sustainable Cement-Based Materials
- Vol. 12 (8) , 941-950
Improving environmental efficiency of ultra-high-performance concrete (UHPC) through appropriate application of ultrafine quartz powder
Ultrafine quartz powder (UQP) can be considered as a kind of physical fillers in concrete production. To improve the environmental efficiency of optimized ultra-high-performance concrete (UHPC), based on Modified Andreason and Andersen packing model (MAA), the UQP was utilized to replace ordinary Portland cement and optimize packing system of UHPC. Subsequently, the physical and hydrated characteristics of UHPC were studied. The results indicate that when UQP is a substitute for Portland cement in the production of UHPC, the influence of its variation content on later age compressive strength of UHPC is difficult to be distinguished. Corresponding to that, the prominent microstructure of the optimized UHPC is developed with high packing density when an optimum addition content of UQP is about 30%. Furthermore, the comprehensive evaluation which is quantified into five indexes (carbon footprint, energy emission, unhydrated clinker, binder and clinker index) demonstrates that the optimized UHPC has a much lower ecological effect in comparison with the majority of UHPC reported in published references, which provides a broad prospect for engineering application of the sustainable UHPC.
- 2 November 2022
- Published by Taylor & Francis in Journal of Sustainable Cement-Based Materials
- Vol. 12 (8) , 941-950
Improving environmental efficiency of ultra-high-performance concrete (UHPC) through appropriate application of ultrafine quartz powder
Ultrafine quartz powder (UQP) can be considered as a kind of physical fillers in concrete production. To improve the environmental efficiency of optimized ultra-high-performance concrete (UHPC), based on Modified Andreason and Andersen packing model (MAA), the UQP was utilized to replace ordinary Portland cement and optimize packing system of UHPC. Subsequently, the physical and hydrated characteristics of UHPC were studied. The results indicate that when UQP is a substitute for Portland cement in the production of UHPC, the influence of its variation content on later age compressive strength of UHPC is difficult to be distinguished. Corresponding to that, the prominent microstructure of the optimized UHPC is developed with high packing density when an optimum addition content of UQP is about 30%. Furthermore, the comprehensive evaluation which is quantified into five indexes (carbon footprint, energy emission, unhydrated clinker, binder and clinker index) demonstrates that the optimized UHPC has a much lower ecological effect in comparison with the majority of UHPC reported in published references, which provides a broad prospect for engineering application of the sustainable UHPC.
- Open Access
Comparative Study of Different Measurement Methods for Characterizing Rheological Properties of Lubrication Layer
The lubrication layer plays a governing role in predicting the pumpability of fresh concrete. To determine the effect of measurement methods on the characterization of the rheological properties of the lubrication layer, different measurement systems, including Sliper, tribometer, and the utilization of a mortar rheometer, were employed. The rheological properties and workability of bulk concrete were measured in parallel to investigate the correlation between them and the rheological properties of the lubrication layer. The results show that the measured values of the rheological parameters of the lubrication layer differ due to the systematic deviation between different measurement methods. The results obtained by both tribometer and mortar rheometer were well-correlated, having a linear relationship with the rheological parameters of bulk concrete. The correlation coefficient between results gained with Sliper and rheological parameters of concrete or lubrication layer determined with other methods was not high enough. Addition friction led to the large accidental error and overestimated yield stress obtained with Sliper. The workability of concrete is only suitable for characterizing the rheological properties of bulk concrete.
Open AccessComparative Study of Different Measurement Methods for Characterizing Rheological Properties of Lubrication Layer
The lubrication layer plays a governing role in predicting the pumpability of fresh concrete. To determine the effect of measurement methods on the characterization of the rheological properties of the lubrication layer, different measurement systems, including Sliper, tribometer, and the utilization of a mortar rheometer, were employed. The rheological properties and workability of bulk concrete were measured in parallel to investigate the correlation between them and the rheological properties of the lubrication layer. The results show that the measured values of the rheological parameters of the lubrication layer differ due to the systematic deviation between different measurement methods. The results obtained by both tribometer and mortar rheometer were well-correlated, having a linear relationship with the rheological parameters of bulk concrete. The correlation coefficient between results gained with Sliper and rheological parameters of concrete or lubrication layer determined with other methods was not high enough. Addition friction led to the large accidental error and overestimated yield stress obtained with Sliper. The workability of concrete is only suitable for characterizing the rheological properties of bulk concrete.
- Open Access
A Rheological Model for Evaluating the Behavior of Shear Thickening of Highly Flowable Mortar
Neither the modified Bingham model nor the Herschel–Bulkley model can be used to characterize and calculate the performance of shear thickening of highly flowable mortar because of their incalculability of the rheological parameters. A new exponential rheological model was established to solve the characterization and calculation of shear thickening of the lubrication layer (highly flowable mortar) during the pumping of concrete in this paper. This new exponential rheological model has three rheological parameters, namely, yield stress, consistency coefficient, and consistency exponent. They can quantitatively describe the yield stress, differential viscosity, and shear thickening degree of highly flowable mortar. The calculating results of the rheological parameters of the newly established model for the mortars with different compositions showed that the consistency exponent of mortar decreased with the increase of its sand-binder ratio or the dosage of fly ash in the binder. This indicates that the shear thickening degree of mortar decreases. The consistency exponent of mortar initially decreases and subsequently increases with the increase in silica fume content or the dosage of the superplasticizer. It illustrates that the degree of the shear thickening of mortar initially decreased and subsequently increased. These varying patterns were confirmed by the rheological experiment of mortars.
Open AccessA Rheological Model for Evaluating the Behavior of Shear Thickening of Highly Flowable Mortar
Neither the modified Bingham model nor the Herschel–Bulkley model can be used to characterize and calculate the performance of shear thickening of highly flowable mortar because of their incalculability of the rheological parameters. A new exponential rheological model was established to solve the characterization and calculation of shear thickening of the lubrication layer (highly flowable mortar) during the pumping of concrete in this paper. This new exponential rheological model has three rheological parameters, namely, yield stress, consistency coefficient, and consistency exponent. They can quantitatively describe the yield stress, differential viscosity, and shear thickening degree of highly flowable mortar. The calculating results of the rheological parameters of the newly established model for the mortars with different compositions showed that the consistency exponent of mortar decreased with the increase of its sand-binder ratio or the dosage of fly ash in the binder. This indicates that the shear thickening degree of mortar decreases. The consistency exponent of mortar initially decreases and subsequently increases with the increase in silica fume content or the dosage of the superplasticizer. It illustrates that the degree of the shear thickening of mortar initially decreased and subsequently increased. These varying patterns were confirmed by the rheological experiment of mortars.
- 8 February 2020
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 103 (6) , 3880-3895
A new hydration kinetics model of composite cementitious materials, Part 2: Physical effect of SCMs
This paper is the second part of an overall research project that aims to model the hydration kinetics of composite cementitious materials. The new hydration kinetic model of Portland cement was constructed in the first part of this research project. The aim of this part is to characterize the physical effect of SCMs by modifying some kinetic parameters of the hydration kinetic model of cement. In this paper, the filler effect of SCMs is attributed to the “dilution effect”, “nucleation effect” and “accelerated dissolution effect”. The dilution effect is considered by introducing the actual water/cement ratio into the kinetic model. The nucleation surface area, nucleation and growth rates are modified to account for the nucleation effect and accelerated dissolution effect of fillers. The simulative fit results show that the extra contribution of SCMs due to their filler effect on hydration of cement at early ages has an upper limit: at most 20% extra nucleation surface area, 30% extra nucleation ratio and 40% extra growth ratio of calcium silicate hydrate (CSH). The new modified kinetic model and the value‐taking method of the newly introduced parameters are verified by simulative fitting to the kinetic data from reference. The apparent activation energies of the nucleation rate, growth rate, and diffusion rate are approximately 35 kJ/mol, 36 kJ/mol and 38.5 kJ/mol, which are slightly smaller than those of the pure Portland cement reported in the first part of this research project.
- 8 February 2020
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 103 (6) , 3880-3895
A new hydration kinetics model of composite cementitious materials, Part 2: Physical effect of SCMs
This paper is the second part of an overall research project that aims to model the hydration kinetics of composite cementitious materials. The new hydration kinetic model of Portland cement was constructed in the first part of this research project. The aim of this part is to characterize the physical effect of SCMs by modifying some kinetic parameters of the hydration kinetic model of cement. In this paper, the filler effect of SCMs is attributed to the “dilution effect”, “nucleation effect” and “accelerated dissolution effect”. The dilution effect is considered by introducing the actual water/cement ratio into the kinetic model. The nucleation surface area, nucleation and growth rates are modified to account for the nucleation effect and accelerated dissolution effect of fillers. The simulative fit results show that the extra contribution of SCMs due to their filler effect on hydration of cement at early ages has an upper limit: at most 20% extra nucleation surface area, 30% extra nucleation ratio and 40% extra growth ratio of calcium silicate hydrate (CSH). The new modified kinetic model and the value‐taking method of the newly introduced parameters are verified by simulative fitting to the kinetic data from reference. The apparent activation energies of the nucleation rate, growth rate, and diffusion rate are approximately 35 kJ/mol, 36 kJ/mol and 38.5 kJ/mol, which are slightly smaller than those of the pure Portland cement reported in the first part of this research project.
- 10 October 2019
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 103 (3) , 1970-1991
A new hydration kinetics model of composite cementitious materials, part 1: Hydration kinetic model of Portland cement
This work is the first part of an overall research project that aims to model the hydration kinetics of modern composite cementitious materials. The aim of this part is to build a hydration kinetic model to characterize the hydration behavior of cement at all ages. In this paper, the nucleation and growth of CSH and the diffusion of water are described by a modified BNG model and a modified Jander's model. The kinetic parameters are obtained by simulative fitting of the model to the experimental data. The linear functions between the nucleation and growth rates and the W/C ratios are given in this paper. The apparent activation energy of the nucleation rate constant, growth rate constant, and generalized diffusion constant are approximately 36.0, 37.5, and 42.0 kJ/mol, respectively. Finally, the phase compositions of hardened cement paste are calculated according to the kinetic model and the reaction formula of cement.
- 10 October 2019
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 103 (3) , 1970-1991
A new hydration kinetics model of composite cementitious materials, part 1: Hydration kinetic model of Portland cement
This work is the first part of an overall research project that aims to model the hydration kinetics of modern composite cementitious materials. The aim of this part is to build a hydration kinetic model to characterize the hydration behavior of cement at all ages. In this paper, the nucleation and growth of CSH and the diffusion of water are described by a modified BNG model and a modified Jander's model. The kinetic parameters are obtained by simulative fitting of the model to the experimental data. The linear functions between the nucleation and growth rates and the W/C ratios are given in this paper. The apparent activation energy of the nucleation rate constant, growth rate constant, and generalized diffusion constant are approximately 36.0, 37.5, and 42.0 kJ/mol, respectively. Finally, the phase compositions of hardened cement paste are calculated according to the kinetic model and the reaction formula of cement.
- 25 August 2019
- Published by Springer Nature in RILEM Bookseries
- p. 346-352
Pumping Process of High Strength Self-consolidating Concrete in the Construction of Skyscraper
- 25 August 2019
- Published by Springer Nature in RILEM Bookseries
- p. 346-352
Pumping Process of High Strength Self-consolidating Concrete in the Construction of Skyscraper
- 6 March 2018
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 132 (3) , 1459-1470
Influence of mechanical grinding on pozzolanic characteristics of circulating fluidized bed fly ash (CFA) and resulting consequences on hydration and hardening properties of blended cement
- 6 March 2018
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 132 (3) , 1459-1470
Influence of mechanical grinding on pozzolanic characteristics of circulating fluidized bed fly ash (CFA) and resulting consequences on hydration and hardening properties of blended cement