AYAdam Yuile

Adam Yuile

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Adam Yuile has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    2D Computational Fluid Dynamics Simulation Analysis of the Assembly of Low‐Temperature Cofired Ceramics/Low‐Temperature Cofired Ceramics and Si/Si Sandwiches by Reactive Bonding

    by Adam Yuile, Alexander Schulz, Erik Wiss, Jens Müller, Steffen Wiese

    Numerical computational fluid dynamics simulations have been performed on 2D sandwich models to compare the performance of low‐temperature cofired ceramics (LTCC)/LTCC and Si/Si sandwiches used in reactive bonding. In the sandwich model layers of solder, silver and a reactive multilayer used to bond the substrates are modeled. Additional to this, the surrounding air environment is also modeled. For simulating the heat released by the multilayer system, a user‐defined function in the form of a square wave is written for the heat source with a defined width, corresponding to the reaction width, and this propagates at a fixed speed. Two sandwiches, one with LTCC/LTCC, and the other with Si/Si, are simulated and their response analyzed in terms of the solidification/melting of the solder and their respective time–temperature histories.

  • Open Access

    Simulation of Mechanical Stresses in BaTiO3 Multilayer Ceramic Capacitors during Desoldering in the Rework of Electronic Assemblies Using a Framework of Computational Fluid Dynamics and Thermomechanical Models

    by Adam Yuile, Erik Wiss, David Barth, Steffen Wiese

    Multilayer ceramic capacitors (MLCCs) are critical components when thermal processes such as reflow desoldering are used during rework of electronic assemblies. The capacitor’s ferroelectric BaTiO3 body is very brittle. Therefore, thermomechanical stresses can cause crack formation and create conductive paths that may short the capacitor. In order to assess the thermally induced mechanical stresses onto an MLCC during reflow desoldering, simulations were carried out, which make use of a framework of computational fluid dynamics and thermomechanical models within the ANSYS software package. In the first step, CFD simulations were conducted to calculate the transient temperature field in the surrounding of the MLCC component, which was then used as an input for FEM simulations to compute the arising mechanical stresses inside the MLCC. The results of the simulations show that the major contribution to mechanical stresses within the MLCC component comes from the mismatch in thermal expansion between the printed circuit board and the MLCC. The temperature gradients along the MLCC component are rather small and account only for moderate internal stresses within the brittle BaTiO3 body.


  • LTCC With Temperature Sensor Array for Monitoring of Reactive Die Bond Processes–Design Optimization Using CFD

    by Adam Yuile, Steffen Wiese

    This paper discusses a design optimisation for the integration of a temperature sensor array for monitoring the spatially distributed course of process temperature during a reactive die-bond process. Since reactive multilayer systems produce the entire fusion heat in a millisecond time frame, it is very difficult to get information about the dynamics of a joining process that they are employed for. Most of the monitoring methods for reactive multilayers are based on high-speed cameras, which cannot be employed in case of a die-bond process. Therefore, this paper studies the influence on temperature measurements in a LTCC (Low Temperature Cofired Ceramics) substrate for different propagation speeds of reactive foils used during bonding processes by CFD (Computational Fluid Dynamics) simulation methods. The assumed reactive multilayer foil thickness is 40 μm. Different speeds of 1, 10 and 100 m/s were studied and temperature probes in the substrate were analysed to try and ascertain the potential limitations of temperature measurements made through probes embedded in an LTCC substrate. It was found that the temperature probes would tend to underestimate the reaction speed, particularly at increased depth, but this can be recovered relatively successfully with judicious selection of criteria for experimentally determining the reaction speed. The results of the simulation study give valuable information for the LTCC layout process with regard to the lateral and the z-axes position of multiple temperature probes forming a 3-dimensional sensor array in the multilayer LTCC substrate. Moreover, the simulation can provide a calibration factor to estimate the real course of process temperature during a reactive die bond process from the lagged temperature responses of the temperature probes inside the LTCC substrate.


  • Application of Reactive Bonding Methods on LTCC Substrates

    by Erik Wiss, Alexander Schulz, Adam Yuile, Jens Mæller, Steffen Wiese

    This paper discusses the application of reactive bonding for the area of L ow Temperature Cofired Ceramics (LTCC) assemblies. The goal is to reduce the thermal-mechanical stresses during soldering by transferring heat only locally to the solder joints without heating the entire component. Such a reactive multilayer system (R MS) consists of alternating nanolayers (10 - 300 nm) of at least two metal components which produce an exothermal reaction after ignition. Although the deposition of an RMS is established on silicon substrates for the use in micro-electromechanical systems (MEMS), it is very challenging to create them on LTCC substrates. One of the main obstacles is to over come all issues connected with the significant roughness, because it is not an optimum territory to deposit nanolayers. In this paper, different methods like chemical mechanical polishing (CMP) and laser ablation, to modify the surface morphology, are presented. A direct relation between the morphology and the exothermal reaction can be observed. In addition, 3-D Computational Fluid Dynamics (CFD) simulations were conducted to analyze the process in more detail. These simulations make use of a shoebox model with different layers and an adjustable user-defined function for the heat release of the RMS to adapt the reaction front velocity and the combustion temperature to the experimental values.


  • Open Access

    Analysis of selective bonding processes using reactive multi-layers for system integration on LTCC based SiPs

    by A. Yuile, A. Schulz, J. Müller, S. Wiese

    This paper discusses the use of reactive multi-layers for selective assembly of ICs (Integrated Circuits) in an LTCC (Low Temperature Co-fired Ceramics) based SiP (System-in-Package). To understand the requirements for the use of self-propagating reactive multilayers in die bonding, CFD (Computational Fluid Dynamics) simulations have been carried out to simulate the die bonding process of a silicon chip onto a ceramic LTCC substrate. Reactive foils of 40 and 80 µm thicknesses and a simulated reaction propagation speed of 1 m/s were studied and used to melt a solder preform underneath a silicon chip. The results of the CFD simulations were analysed, particularly with respect to temperature and liquid fraction contours, as well as time–temperature histories obtained from temperature probes which were included in the model, such as to approximate the real behaviour of Pt-100 temperature probes, when a real bonding process is being tracked. The CFD method, in this instance realised with ANSYS Fluent software, can track the melting and solidification of the solder as well as model the influence of latent heat, which is crucial to ascertaining the true evolution of the bonding process.


  • Open Access

    The Simulated Effect of Adding Solder Layers on Reactive Multilayer Films Used for Joining Processes

    by Adam Yuile, Alexander Schulz, Erik Wiss, Jens Müller, Steffen Wiese

    In order to introduce new bonding methods in the area of electronic packaging a theoretical analysis was conducted, which should give substantial information about the potential of reactive multilayer systems (rms) to create sufficient local heat for joining processes between silicon chips and ceramic substrates. For this purpose, thermal CFD (computational fluid dynamics) simulations have been carried out to simulate the temperature profile of the bonding zone during and after the reaction of the rms. This thermal analysis considers two different configurations. The first configuration consists of a silicon chip that is bonded to an LTCC-substrate (Low Temperature Co-fired Ceramics) using a bonding layer that contains an rms and a solder preform. The reaction propagation speed of the reactive multilayer was set to a value of 1 m/s, in order to partially melt a solder preform underneath a silicon chip. The second configuration, which consists only of the LTCC-substrate and the rms, was chosen to study the differences between the thermal outputs of the two arrangements. The analysis of the CFD simulations was particularly focused on interpretations of the temperature and liquid fraction contours. The CFD thermal simulation analysis conducted contains a melting/solidification model which can track the molten/solid state of the solder in addition to modelling the influence of latent heat. To provide information for the design of a test-substrate for experimental investigations, the real behaviour of Pt-100 temperature probes on the LTCC-substrate was simulated, in order to monitor an actual bonding in the experiment. All simulations were carried out using the ANSYS Fluent software.