Linlin Gu

Linlin Gu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Linlin Gu has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Exploration of the Chloride Binding Behavior of Anhydrous Calcium Sulfoaluminate Under Dual Chloride Ingress Modes

    by Zirui Cheng, Luyan Ji, Zhen Wang, Linlin Gu, Wenbin Tang

    This study explored the chloride binding characteristics and mechanisms of sulphoaluminate cement (SAC) by isolating its principal mineral component, anhydrous calcium sulphoaluminate (C4A3S-), as the research object. Chloride ingress was investigated under external penetration and internal incorporation conditions, with gypsum dosage varied at molar ratios of 1:0, 1:1, and 1:2 relative to  C4A3S-. Through chloride binding experiments and hydration product analysis performed by XRD and TG, the following findings were obtained: under external chloride exposure, the binding capacity increased with rising solution concentration and immersion time. External chloride binding was attributed to SO42−/Cl− ion exchange in AFm to generate Friedel’s salt and was complemented by physical adsorption of chloride in AH3 gel. Under internal chloride incorporation, binding capacity increased progressively with curing age. Internal chloride binding involved the direct participation of Cl− in hydration reactions to form Friedel’s salt in addition to the chemical reaction of AFm and the physical adsorption of AH3. Gypsum dosage critically regulates the AFm/AFt ratio, which in turn governs chloride binding efficiency under both external and internal chloride scenarios (e.g., after immersion in 1 mol/L NaCl solution, the bound chloride content for C4A3S-/gypsum ratios of 1:0, 1:1, and 1:2 was 50.94, 27.28, and 13.47 mg/g, respectively).


  • Open Access

    Response of a Coral Reef Sand Foundation Densified through the Dynamic Compaction Method

    by Linlin Gu, Weihao Yang, Zhen Wang, Jianping Wang, Guanlin Ye

    Dynamic compaction is a method of ground reinforcement that uses the huge impact energy of a free-falling hammer to compact the soil. This study presents a DC method for strengthening coral reef foundations in the reclamation area of remote sea islands. Pilot tests were performed to obtain the design parameters before official DC operation. The standard penetration test (SPT), shallow plate-load test (PLT), and deformation investigation were conducted in two improvement regions (A1 and A2) with varying tamping energies. During the deformation test, the depth of the tamping crater for the first two points’ tamping and the third full tamping was observed at two distinct sites. The allowable ground bearing capacity at two disparate field sites was at least 360 kPa. The reinforcement depths were 3.5 and 3.2 m in the A1 and A2 zones, respectively. The DC process was numerically analyzed by the two-dimensional particle flow code, PFC2D. It indicated that the reinforcement effect and effective reinforcement depth were consistent with the field data. The coral sand particles at the bottom of the crater were primarily broken down in the initial stage, and the particle-crushing zone gradually developed toward both sides of the crater. The force chain developed similarly at the three tamping energies (800, 1500, and 2000 kJ), and the impact stress wave propagated along the sand particles primarily in the vertical direction.


  • Open Access

    Response of coral reef sand foundation densified through dynamic compaction method

    by Zhen Wang, Linlin Gu, Xiao Wang, Weihao Yang, Yanyu Qiu, Jianping Wang

    As an effective ground reinforcement method, the dynamic compaction (DC) technique is widely applied for various soils and geotechnical conditions; however, its application in the regions with thick coral reef sand (CRS) is limited. This study presents a DC method for strengthening coral reef foundations in the reclamation area of the South China Sea. Pilot tests were performed to obtain the crucial design parameters before official DC operation. The field tests included a deformation test, standard penetration test (SPT), and shallow plate load test in two different improvement zones (A1 and A2) with different tamping energies. During the deformation test, the crater depth in three diverse passes (two-pass point tamping and one-pass full tamping) was observed in these two specific areas. The SPT and shallow plate load tests were carried out to estimate the final effect of DC. The allowable ground bearing capacity at the two disparate field sites was at least 360 kPa. The reinforcement depths were 3.5 and 3.2 m in the A1 and A2 zones, respectively. The DC process was numerically analyzed by the particle flow discrete element code, PFC2D. The computational results indicated that the reinforcement effect and effective reinforcement depth were consistent with the field data. During the DC process, the coral sand particles at the bottom of the crater were primarily broken down in the initial stage, and the particle-crushing zone gradually developed toward both sides of the tamping crater. The force chain developed similarly at the three different tamping energies (800, 1500, and 2000 KJ), and the impact stress wave propagated along the sand particles primarily in the vertical direction. This study provides relevant insights into the DC mechanism involving CRS as foundation for structures.

  • Open Access

    Experimental Study of Energy Evolution at a Discontinuity in Rock under Cyclic Loading and Unloading

    by Wei Zheng, Linlin Gu, Zhen Wang, Junnan Ma, Hujun Li, Hang Zhou

    Energy is often dissipated and released in the process of rock deformation and failure. To study the energy evolution of rock discontinuities under cyclic loading and unloading, cement mortar was used as rock material and a CSS-1950 rock biaxial rheological testing machine was used to conduct graded cyclic loading and unloading tests on Barton’s standard profile line discontinuities with different joint roughness coefficients (JRCs). According to the deformation characteristics of the rock discontinuity sample, the change of internal energy is calculated and analyzed. The experimental results show that under the same cyclic stress, the samples harden with the increase in the number of cycles. With the increase of cyclic stress, the dissipated energy density of each stage gradually exceeds the elastic energy density and occupies a dominant position and increases rapidly as failure becomes imminent. In the process of increasing the shear stress step-by-step, the elastic energy ratio shows a downward trend, but the dissipated energy is contrary to it. The energy dissipation ratio can be used to characterize the internal damage of the sample under load. In the initial stage of fractional loading, the sample is in the extrusion compaction stage, and the energy dissipation ratio remains quasi-constant; then the fracture develops steadily, the damage inside the sample intensifies, and the energy dissipation ratio increases linearly (albeit at a low rate). When the energy storage limit is reached, the growth rate of energy dissipation ratio increases and changes when the stress level reaches a certain threshold. The increase of the roughness of rock discontinuity samples will improve their energy storage capacity to a certain extent.


  • Pyrene-based sulfonated organic porous materials for rapid adsorption of cationic dyes in water

    by Xiaodong Zhu, Danxuan Xue, Linlin Gu, Wenxin Li, Aming Xie, Zhen Wang

    Porous organic polymers (POP) have gained attention because of their high specific surface area, porosity and their simplicity in synthesis, but for the most part they are hydrophobic because of their organic backbone, making it difficult to expand their applications. Here, we have obtained poly(pyrene) porous organic polymers (PyPOP) through the polymerization of pyrene monomers catalyzed by aluminium trichloride, which is a simple and inexpensive synthesis method. The sulfonated poly(pyrene) porous organic polymers (PyPOP-SO3H) obtained showed rapid adsorption of cationic dyes, especially malachite green (MG adsorption 1607 mg/g) and methylene blue (MB adsorption 1220 mg/g) in pH = 7 aqueous solution, room temperature. The results show that the Freundlich model is more in line with the adsorption process than the Langmuir model, whether for methylene blue or malachite green. In addition, the PSO kinetic model fits better than PFO kinetic model, whether it is for the adsorption of methylene blue or malachite green. The excellent adsorption performance of PyPOP-SO3H for cationic dyes may be due to the introduction of sulfonic acid groups, which not only increases the specific surface area, but also allows better dispersion in water, increasing contact points and adsorption efficiency. This research expands the scope of exploration and application of POP.