Alba Valéria Brandão Canellas

Stepped spillways have been increasingly used to handle flood releases from large dams associated with hydropower plants, and it is important to evaluate the fluctuating pressure field on the steps. Hydraulic model investigations were conducted on three 53° (1V:0.75H) sloping and relatively large-stepped chutes to characterize the mean, fluctuating, and extreme pressures acting on the most critical regions of the step faces, near their outer edges. The pressure development along the chutes is presented, generally indicating an increase of the modulus of pressure coefficients up to the vicinity of the point of inception of air entrainment, and a decrease further downstream. The extreme pressure coefficients along the spillway are fitted by an empirical formula, and the critical conditions potentially leading to cavitation on prototypes are calculated. The correlation between the cavitation index and the friction factor is also applied for predicting the onset of cavitation on prototypes, and the results are compared with the pressure data-based method. Generally, the results obtained from those methods yield typical values for the cavitation index in the vicinity of the point of inception, varying approximately from 0.8 to 0.6, respectively. In light of these results, maximum unit discharges of about 15–20 m²/s are considered advisable on 53° sloping large-stepped spillways without artificial aeration, for step heights ranging from 0.6 to 1.2 m. For much higher unit discharges, a considerable reach of the spillway may potentially be prone to the risk of cavitation damage.

Stepped spillways aim to dissipate part of the upstream energy during the flow passage by the chute. However, the use of these structures is limited to a restrict range of specific discharges due to the risk of cavitation damage. As the air entrainment into the flow assists the concrete protection against the aforementioned damages, a possible solution by aerators installed along the chute, already disseminated to smooth chutes, is being studied to be used also in stepped spillways. The purpose of the present paper is to characterize a flow over a stepped chute with induced aeration by deflector and air supply by an airtight chamber trough tests conducted on a reduced scale physical model. The main regions observed during the tests are presented and were developed four equations that allow to approximately predict the location of the main regions for a given spillway.

The ski jump type spillway is present in large Brazilian dams. After the operation of this type of spillway, a scour hole is originated downstream of the spillway toe, complementing the energy dissipation system, because the jet is cushioned by the waterbed. As the excavation of the scour hole evolves, its shape changes, with the induction of different behaviors of the jet flow within the waterbed. The importance of this scientific study is due to the fact that scour holes downstream of ski jump spillways are in constant transformation, which can cause changes in the patterns of dynamic pressures caused on the bottom. Unexpected erosions can cause instability in the submerged slopes of the pit, jeopardizing the foundation of the dam. In this work it was proceeded physical experiments, by sectional modeling (2D), in two reduced models of 1:50 and 1:100 scales, considering two stages of erosion depths in solid bottom (fixed). It was analyzed the impact site of the jet flow on the bottom, which has the major mean dynamic pressure. As result, it was possible to identify the scale effect in the pressure coefficient between the two models tested, which allowed the adjustment of trend lines that aid to estimate the pressures that occur in prototypes, increasing safety in operation of ski jump spillways.

Stepped spillways have been widely used for flood runoff due to of their constructive advantages and in regards to energy dissipation during the drop, allowing downstream dissipation structures to be designed in smaller dimensions. Due to the need for further studies on the effect of runoff in the chute of the stepped spillway and the analysis of dimensionless numbers used to characterize the longitudinal distribution of the pressures acting on the faces of the steps of a spillway, this study aims to characterize the acting forces on the steps of said spillways. Analyses were performed on a physical model of spillway with a slope of 1V: 0.75H and steps with a height of 6 centimeters. The pressure fields on the steps were analyzed and compared with results found in literature. As a general finding concerning the pressure in the horizontal faces, it was ascertained that the traction and the compression loads have relatively similar magnitudes, the negative pressures being more intense. Regarding the maximum pressures at the horizontal faces of the steps, it should be emphasized that the maximum values of compression have occurred at the end of the chute and that the lower discharges yielded higher values of pressure coefficients.