Hossam Youssef Hegazy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hossam Youssef Hegazy has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Elwy E. El-Kholy
Faculty of Engineering, Menoufia University, Shebin El-Kom 32511, Egypt
2 shared publications - Moayed Mohamed
Faculty of Technology and Education, Sohag University, Sohag 82524, Egypt
2 shared publications - Mohamed E. Ibrahim
High Voltage and Dielectric Materials Laboratory, Faculty of Engineering, Menoufia University, Shebin El-Kom, Egypt
2 shared publications - Mohamed S. Elrefaey
Faculty of Technological Industry and Energy, Delta Technological University (DTU), Quwaysna 32631, Egypt
2 shared publications - Saad A. Mohamed Abdelwahab
Department of Electrical, Faculty of Technology and Education, Suez University, Suez, Egypt
2 shared publications - Samia Abdalfatah
Faculty of Industrial Education, Helwan University, Cairo 11835, Egypt
2 shared publications
Latest Publications
- Open Access
Performance Comparison of Intelligent Energy Management Strategies for Hybrid Electric Vehicles with Photovoltaic Fuel Cell and Battery Integration
This study presents an optimized and comparative investigation of four intelligent energy management strategies—Proportional–Integral–Derivative (PID), Fuzzy Logic Control (FLC), Equivalent Consumption Minimization Strategy (ECMS), and Artificial Neural Network (ANN)—applied to a photovoltaic–fuel cell–battery hybrid electric vehicle (PV–FC–HEV). A high-fidelity MATLAB/Simulink model integrates a 6 kW proton-exchange membrane fuel cell (PEMFC), a 500 W photovoltaic subsystem with MPPT, and a lithium-ion battery (LiB) pack. While 1000 W/m2 represents Standard Test Conditions (STC), the level of 400 W/m2 was specifically selected to simulate average cloudy conditions common in urban driving environments, rather than standard NOCT (800 W/m2), to test the EMS’s robustness under significantly reduced PV support and stressed battery conditions (initial SOC = 30%). While surface contamination and the resulting performance degradation significantly impact real-world results, this study assumes a clean surface to establish an idealized performance baseline for the control algorithms. However, the authors acknowledge that contaminant accumulation is a key factor; future work will incorporate a degradation factor (e.g., a 10–15% efficiency penalty) to evaluate the reliability of these EMS strategies under actual operating conditions. ECMS achieved the lowest hydrogen consumption, saving up to 10 L compared with PID, while ANN maintained the most stable state of charge (SOC > 80%), minimizing deep discharge cycles and improving operational stability. FLC provided balanced operation under fluctuating irradiance. Overall, ANN offered the most harmonized energy flow and dynamic stability, whereas ECMS maximized fuel economy. The findings provide practical guidance for designing sustainable and intelligent control systems in next-generation hybrid electric vehicles.
Open AccessPerformance Comparison of Intelligent Energy Management Strategies for Hybrid Electric Vehicles with Photovoltaic Fuel Cell and Battery Integration
This study presents an optimized and comparative investigation of four intelligent energy management strategies—Proportional–Integral–Derivative (PID), Fuzzy Logic Control (FLC), Equivalent Consumption Minimization Strategy (ECMS), and Artificial Neural Network (ANN)—applied to a photovoltaic–fuel cell–battery hybrid electric vehicle (PV–FC–HEV). A high-fidelity MATLAB/Simulink model integrates a 6 kW proton-exchange membrane fuel cell (PEMFC), a 500 W photovoltaic subsystem with MPPT, and a lithium-ion battery (LiB) pack. While 1000 W/m2 represents Standard Test Conditions (STC), the level of 400 W/m2 was specifically selected to simulate average cloudy conditions common in urban driving environments, rather than standard NOCT (800 W/m2), to test the EMS’s robustness under significantly reduced PV support and stressed battery conditions (initial SOC = 30%). While surface contamination and the resulting performance degradation significantly impact real-world results, this study assumes a clean surface to establish an idealized performance baseline for the control algorithms. However, the authors acknowledge that contaminant accumulation is a key factor; future work will incorporate a degradation factor (e.g., a 10–15% efficiency penalty) to evaluate the reliability of these EMS strategies under actual operating conditions. ECMS achieved the lowest hydrogen consumption, saving up to 10 L compared with PID, while ANN maintained the most stable state of charge (SOC > 80%), minimizing deep discharge cycles and improving operational stability. FLC provided balanced operation under fluctuating irradiance. Overall, ANN offered the most harmonized energy flow and dynamic stability, whereas ECMS maximized fuel economy. The findings provide practical guidance for designing sustainable and intelligent control systems in next-generation hybrid electric vehicles.
- Open Access
- 29 June 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (13) , 5590
Enhanced Adaptive Dynamic Surface Sliding Mode Control for Optimal Performance of Grid-Connected Photovoltaic Systems
This study presents an enhanced, adaptive, and dynamic surface sliding mode control (SMC), a cutting-edge method for improving grid-connected photovoltaic (PV) system performance. The suggested control approach uses dynamic SMC and adaptive approaches to enhance the robustness and efficiency of a system. Proportional–integral (PI) and SMC, two control systems for maximum power point tracking (MPPT) in PV systems, are compared in this paper. This study finds that the SMC system is a more effective and efficient MPPT approach for PV systems compared to the conventional PI control system. The SMC system’s unique feature is the capacity to stabilize grid voltage and attain a modulation index of less than one. An important component of power electronic system control is the index, which acts as a parameter representing the relationship between the output signal’s amplitude and the reference signal’s amplitude. The SMC method demonstrates improved robustness, efficiency, and stability, especially in dynamic operating settings with load and solar radiation changes. Compared to the PI control, the SMC exhibits a noteworthy 75% reduction in voltage fluctuations and an improvement in the power output of 5% to 10%. Regarding output power optimization, voltage stability, and accurate current tracking, the SMC system performs better than the PI control system. Furthermore, the SMC technique maintains a modulation index below one and guarantees grid voltage stability, both of which are essential for the efficiency and stability of power electrical systems.
- 29 June 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (13) , 5590
Open AccessEnhanced Adaptive Dynamic Surface Sliding Mode Control for Optimal Performance of Grid-Connected Photovoltaic Systems
This study presents an enhanced, adaptive, and dynamic surface sliding mode control (SMC), a cutting-edge method for improving grid-connected photovoltaic (PV) system performance. The suggested control approach uses dynamic SMC and adaptive approaches to enhance the robustness and efficiency of a system. Proportional–integral (PI) and SMC, two control systems for maximum power point tracking (MPPT) in PV systems, are compared in this paper. This study finds that the SMC system is a more effective and efficient MPPT approach for PV systems compared to the conventional PI control system. The SMC system’s unique feature is the capacity to stabilize grid voltage and attain a modulation index of less than one. An important component of power electronic system control is the index, which acts as a parameter representing the relationship between the output signal’s amplitude and the reference signal’s amplitude. The SMC method demonstrates improved robustness, efficiency, and stability, especially in dynamic operating settings with load and solar radiation changes. Compared to the PI control, the SMC exhibits a noteworthy 75% reduction in voltage fluctuations and an improvement in the power output of 5% to 10%. Regarding output power optimization, voltage stability, and accurate current tracking, the SMC system performs better than the PI control system. Furthermore, the SMC technique maintains a modulation index below one and guarantees grid voltage stability, both of which are essential for the efficiency and stability of power electrical systems.
- Open Access
Optimal Control and Optimization of Grid-Connected PV and Wind Turbine Hybrid Systems Using Electric Eel Foraging Optimization Algorithms
This paper presents a comprehensive exploration of a hybrid energy system that integrates wind turbines with photovoltaics (PVs) to address the intermittent nature of electricity production from these sources. The necessity for such technology arises from the sporadic nature of electricity generated by PV cells and wind turbines. The envisioned outcome is an emissions-free, more efficient alternative to traditional energy sources. A variety of optimization techniques are utilized, specifically the Particle Swarm Optimization (PSO) algorithm and Electric Eel Foraging Optimization (EEFO), to achieve optimal power regulation and seamless integration with the public grid, as well as to mitigate anticipated loading issues. The employed mathematical modeling and simulation techniques are used to assess the effectiveness of EEFO in optimizing the operation of grid-connected PV and wind turbine hybrid systems. In this paper, the optimization methods applied to the system’s architecture are described in detail, providing a clear understanding of the intricate nature of the approach. The efficacy of these optimization strategies is rigorously evaluated through simulations of diverse operating scenarios using MATLAB/SIMULINK. The results demonstrate that the proposed optimization strategies are not only capable of precisely and swiftly compensating for linked loads, but also effectively controlling the energy supply to maintain the load’s power at the desired level. The findings underscore the potential of this hybrid energy system to offer a sustainable and reliable solution for meeting power demands, contributing to the advancement of clean and efficient energy technologies. The results demonstrate the capability of the proposed approach to improve system performance, maximize energy yield, and enhance grid integration, thereby contributing to the advancement of renewable energy technologies and sustainable energy systems.
Open AccessOptimal Control and Optimization of Grid-Connected PV and Wind Turbine Hybrid Systems Using Electric Eel Foraging Optimization Algorithms
This paper presents a comprehensive exploration of a hybrid energy system that integrates wind turbines with photovoltaics (PVs) to address the intermittent nature of electricity production from these sources. The necessity for such technology arises from the sporadic nature of electricity generated by PV cells and wind turbines. The envisioned outcome is an emissions-free, more efficient alternative to traditional energy sources. A variety of optimization techniques are utilized, specifically the Particle Swarm Optimization (PSO) algorithm and Electric Eel Foraging Optimization (EEFO), to achieve optimal power regulation and seamless integration with the public grid, as well as to mitigate anticipated loading issues. The employed mathematical modeling and simulation techniques are used to assess the effectiveness of EEFO in optimizing the operation of grid-connected PV and wind turbine hybrid systems. In this paper, the optimization methods applied to the system’s architecture are described in detail, providing a clear understanding of the intricate nature of the approach. The efficacy of these optimization strategies is rigorously evaluated through simulations of diverse operating scenarios using MATLAB/SIMULINK. The results demonstrate that the proposed optimization strategies are not only capable of precisely and swiftly compensating for linked loads, but also effectively controlling the energy supply to maintain the load’s power at the desired level. The findings underscore the potential of this hybrid energy system to offer a sustainable and reliable solution for meeting power demands, contributing to the advancement of clean and efficient energy technologies. The results demonstrate the capability of the proposed approach to improve system performance, maximize energy yield, and enhance grid integration, thereby contributing to the advancement of renewable energy technologies and sustainable energy systems.
- Open Access
Wind Energy Conversion Systems Based on a Synchronous Generator: Comparative Review of Control Methods and Performance
Recently, controlling a wind energy conversion system (WECS) under fluctuating wind speed and enhancing the quality of power delivered to the grid has been a demanding challenge for many researchers. This paper provides a comprehensive review of synchronous generator-based WECSs. This paper will investigate the growth of wind energy in Egypt and throughout the world, as well as the technological and financial significance of wind energy. The block diagram of a typical grid-connected WECS, power control techniques, characteristic power curve-based maximum power point tracking (MPPT), and MPPT techniques are also presented in this study. Moreover, this study compares different power converter topologies for grid-connected and independent WECSs that use a permanent magnet synchronous generator (PMSG).
Open AccessWind Energy Conversion Systems Based on a Synchronous Generator: Comparative Review of Control Methods and Performance
Recently, controlling a wind energy conversion system (WECS) under fluctuating wind speed and enhancing the quality of power delivered to the grid has been a demanding challenge for many researchers. This paper provides a comprehensive review of synchronous generator-based WECSs. This paper will investigate the growth of wind energy in Egypt and throughout the world, as well as the technological and financial significance of wind energy. The block diagram of a typical grid-connected WECS, power control techniques, characteristic power curve-based maximum power point tracking (MPPT), and MPPT techniques are also presented in this study. Moreover, this study compares different power converter topologies for grid-connected and independent WECSs that use a permanent magnet synchronous generator (PMSG).
- Open Access
Multiple-Source Single-Output Buck-Boost DC–DC Converter with Increased Reliability for Photovoltaic (PV) Applications
This paper presents an improved topology for a DC–DC converter suitable for PV applications. The proposed converter has the ability to be energized from multiple DC sources. Hence, it can be energized from two, three or a higher number of sources according to the number of modules adopted in its design. The proposed converter can supply a single load with DC power at a voltage lower or higher than the summation of all excitation DC voltages with a non-reversed voltage polarity at its output. Moreover, it provides a more reliable operation compared to other DC–DC converters due to its ability for operation with partial failures in its exciting sources. In this paper, the theoretical discussion of the proposed converter is presented considering its construction and its principle of operation. The performance of the proposed converter is theoretically evaluated using simulation based on power simulation (PSIM) software at different conditions. The performance of the converter is theoretically evaluated using PSIM considering photovoltaic (PV) sources as input sources for the proposed converter to show its validity for renewable energy applications. For more evaluation, experimental work is carried out by building a prototype and testing it at different operating conditions.
Open AccessMultiple-Source Single-Output Buck-Boost DC–DC Converter with Increased Reliability for Photovoltaic (PV) Applications
This paper presents an improved topology for a DC–DC converter suitable for PV applications. The proposed converter has the ability to be energized from multiple DC sources. Hence, it can be energized from two, three or a higher number of sources according to the number of modules adopted in its design. The proposed converter can supply a single load with DC power at a voltage lower or higher than the summation of all excitation DC voltages with a non-reversed voltage polarity at its output. Moreover, it provides a more reliable operation compared to other DC–DC converters due to its ability for operation with partial failures in its exciting sources. In this paper, the theoretical discussion of the proposed converter is presented considering its construction and its principle of operation. The performance of the proposed converter is theoretically evaluated using simulation based on power simulation (PSIM) software at different conditions. The performance of the converter is theoretically evaluated using PSIM considering photovoltaic (PV) sources as input sources for the proposed converter to show its validity for renewable energy applications. For more evaluation, experimental work is carried out by building a prototype and testing it at different operating conditions.
- Open Access
A Proposed Three-Phase Induction Motor Drive System Suitable for Golf Cars
In this paper, a proposed electric drive system for a three-phase induction motor is presented. The proposed drive system is suggested for a golf car as one type of electric vehicle. The suggested system consists of three similar single-phase buck–boost converters. Hence, each single-phase buck–boost converter is used as a buck–boost inverter and is used to energize only one phase of the induction motor. The suggested system has the advantage of high reliability, as it can deal with different fault conditions such as battery and motor winding faults. The suggested electric drive system depends on a buck–boost converter which gives variable voltages as well as variable frequencies. Thus, variable speeds of the electric vehicles can be easily achieved. A variable DC voltage (positive or negative) can be achieved at the output of the adopted buck–boost converter, which is considered another advantage of the proposed drive system. This DC voltage can be used to achieve braking of the induction motor used to drive the electric vehicle. Therefore, this advantage can be used instead of ordinary mechanical braking to increase vehicle reliability. To demonstrate our proposed idea, a simulation study is presented. The simulation is carried out using Power Simulation Program (PSIM) software. The simulation study takes into consideration the performance of the adopted buck–boost converter under different conditions to present its advantages. Furthermore, a performance study of the suggested induction motor drive system is carried out under different conditions ranging from healthy to faulty conditions to test system reliability. For more illustration, an experimental prototype of the adopted buck–boost converter is built, and its performance is studied. From all the obtained results, the efficacy of the proposed system is demonstrated.
Open AccessA Proposed Three-Phase Induction Motor Drive System Suitable for Golf Cars
In this paper, a proposed electric drive system for a three-phase induction motor is presented. The proposed drive system is suggested for a golf car as one type of electric vehicle. The suggested system consists of three similar single-phase buck–boost converters. Hence, each single-phase buck–boost converter is used as a buck–boost inverter and is used to energize only one phase of the induction motor. The suggested system has the advantage of high reliability, as it can deal with different fault conditions such as battery and motor winding faults. The suggested electric drive system depends on a buck–boost converter which gives variable voltages as well as variable frequencies. Thus, variable speeds of the electric vehicles can be easily achieved. A variable DC voltage (positive or negative) can be achieved at the output of the adopted buck–boost converter, which is considered another advantage of the proposed drive system. This DC voltage can be used to achieve braking of the induction motor used to drive the electric vehicle. Therefore, this advantage can be used instead of ordinary mechanical braking to increase vehicle reliability. To demonstrate our proposed idea, a simulation study is presented. The simulation is carried out using Power Simulation Program (PSIM) software. The simulation study takes into consideration the performance of the adopted buck–boost converter under different conditions to present its advantages. Furthermore, a performance study of the suggested induction motor drive system is carried out under different conditions ranging from healthy to faulty conditions to test system reliability. For more illustration, an experimental prototype of the adopted buck–boost converter is built, and its performance is studied. From all the obtained results, the efficacy of the proposed system is demonstrated.