Samia Abdalfatah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Samia Abdalfatah has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Elwy E. El-Kholy
Faculty of Engineering, Menoufia University, Shebin El-Kom 32511, Egypt
2 shared publications - Hossam Youssef Hegazy
Electrical Department, Faculty of Technology and Education, Helwan University, Helwan 11795, Egypt
2 shared publications - Mohamed E. Ibrahim
High Voltage and Dielectric Materials Laboratory, Faculty of Engineering, Menoufia University, Shebin El-Kom, Egypt
2 shared publications - Mohamed S. Elrefaey
Faculty of Technological Industry and Energy, Delta Technological University (DTU), Quwaysna 32631, Egypt
2 shared publications - Elsayed Mohamed Tag Eldin
Center of Research, Faculty of Engineering, Future University in Egypt, New Cairo 11835, Egypt
1 shared publication
Latest Publications
- Open Access
Multiple-Source Single-Output Buck-Boost DC–DC Converter with Increased Reliability for Photovoltaic (PV) Applications
This paper presents an improved topology for a DC–DC converter suitable for PV applications. The proposed converter has the ability to be energized from multiple DC sources. Hence, it can be energized from two, three or a higher number of sources according to the number of modules adopted in its design. The proposed converter can supply a single load with DC power at a voltage lower or higher than the summation of all excitation DC voltages with a non-reversed voltage polarity at its output. Moreover, it provides a more reliable operation compared to other DC–DC converters due to its ability for operation with partial failures in its exciting sources. In this paper, the theoretical discussion of the proposed converter is presented considering its construction and its principle of operation. The performance of the proposed converter is theoretically evaluated using simulation based on power simulation (PSIM) software at different conditions. The performance of the converter is theoretically evaluated using PSIM considering photovoltaic (PV) sources as input sources for the proposed converter to show its validity for renewable energy applications. For more evaluation, experimental work is carried out by building a prototype and testing it at different operating conditions.
Open AccessMultiple-Source Single-Output Buck-Boost DC–DC Converter with Increased Reliability for Photovoltaic (PV) Applications
This paper presents an improved topology for a DC–DC converter suitable for PV applications. The proposed converter has the ability to be energized from multiple DC sources. Hence, it can be energized from two, three or a higher number of sources according to the number of modules adopted in its design. The proposed converter can supply a single load with DC power at a voltage lower or higher than the summation of all excitation DC voltages with a non-reversed voltage polarity at its output. Moreover, it provides a more reliable operation compared to other DC–DC converters due to its ability for operation with partial failures in its exciting sources. In this paper, the theoretical discussion of the proposed converter is presented considering its construction and its principle of operation. The performance of the proposed converter is theoretically evaluated using simulation based on power simulation (PSIM) software at different conditions. The performance of the converter is theoretically evaluated using PSIM considering photovoltaic (PV) sources as input sources for the proposed converter to show its validity for renewable energy applications. For more evaluation, experimental work is carried out by building a prototype and testing it at different operating conditions.
- Open Access
A Proposed Three-Phase Induction Motor Drive System Suitable for Golf Cars
In this paper, a proposed electric drive system for a three-phase induction motor is presented. The proposed drive system is suggested for a golf car as one type of electric vehicle. The suggested system consists of three similar single-phase buck–boost converters. Hence, each single-phase buck–boost converter is used as a buck–boost inverter and is used to energize only one phase of the induction motor. The suggested system has the advantage of high reliability, as it can deal with different fault conditions such as battery and motor winding faults. The suggested electric drive system depends on a buck–boost converter which gives variable voltages as well as variable frequencies. Thus, variable speeds of the electric vehicles can be easily achieved. A variable DC voltage (positive or negative) can be achieved at the output of the adopted buck–boost converter, which is considered another advantage of the proposed drive system. This DC voltage can be used to achieve braking of the induction motor used to drive the electric vehicle. Therefore, this advantage can be used instead of ordinary mechanical braking to increase vehicle reliability. To demonstrate our proposed idea, a simulation study is presented. The simulation is carried out using Power Simulation Program (PSIM) software. The simulation study takes into consideration the performance of the adopted buck–boost converter under different conditions to present its advantages. Furthermore, a performance study of the suggested induction motor drive system is carried out under different conditions ranging from healthy to faulty conditions to test system reliability. For more illustration, an experimental prototype of the adopted buck–boost converter is built, and its performance is studied. From all the obtained results, the efficacy of the proposed system is demonstrated.
Open AccessA Proposed Three-Phase Induction Motor Drive System Suitable for Golf Cars
In this paper, a proposed electric drive system for a three-phase induction motor is presented. The proposed drive system is suggested for a golf car as one type of electric vehicle. The suggested system consists of three similar single-phase buck–boost converters. Hence, each single-phase buck–boost converter is used as a buck–boost inverter and is used to energize only one phase of the induction motor. The suggested system has the advantage of high reliability, as it can deal with different fault conditions such as battery and motor winding faults. The suggested electric drive system depends on a buck–boost converter which gives variable voltages as well as variable frequencies. Thus, variable speeds of the electric vehicles can be easily achieved. A variable DC voltage (positive or negative) can be achieved at the output of the adopted buck–boost converter, which is considered another advantage of the proposed drive system. This DC voltage can be used to achieve braking of the induction motor used to drive the electric vehicle. Therefore, this advantage can be used instead of ordinary mechanical braking to increase vehicle reliability. To demonstrate our proposed idea, a simulation study is presented. The simulation is carried out using Power Simulation Program (PSIM) software. The simulation study takes into consideration the performance of the adopted buck–boost converter under different conditions to present its advantages. Furthermore, a performance study of the suggested induction motor drive system is carried out under different conditions ranging from healthy to faulty conditions to test system reliability. For more illustration, an experimental prototype of the adopted buck–boost converter is built, and its performance is studied. From all the obtained results, the efficacy of the proposed system is demonstrated.