RARasha Al-Saedi

Rasha Al-Saedi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Rasha Al-Saedi has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Microaerobic Moving-Bed Biofilm Reactors for Nitrogen and Organic Removal from Wastewater: Effect of Initial Inoculum

    by Firdous Mothehir Awad, Rasha Al-Saedi, Nadia Matter Almhana

    Development of novel approaches that achieve high nitrogen and organic compound removal performance has gained much attention technically and scientifically. This study was carried out to assess the nutrient and organic removal from synthetic wastewater using two lab-scale moving bed biofilm reactors (MBBRs) and plastic carriers as the main media at influent nitrogen, organic, and hydraulic loading rates of 888 g N/m 3 .d, 5,022 g chemical oxygen demand (COD)/m 3 .d, and 1.8 m 3 /(m 2 .d), respectively. Two different biofilm compositions were inoculated into the reactors—whereby the concentration of Pseudomonadota and Acidobacteriota in the first inoculated biofilm was twice as high as in the second one, but the level of Actinomycetota in the first biofilm was only one-fifth of those in the second biofilm. Results showed that the treatment process was successfully accomplished in the MBBR under controlled environmental regimes (temperature = 32–36°C, dissolved oxygen = 0.4 ± 0.02 mg/L, and pH = 7.4 ± 0.3). The average removal efficiencies of NH 4 -N, NO 2 -N, and COD were 91%, 91%, and 89% in the first reactor, while they were 92%, 91%, and 88% in the second reactor, achieving nitrogen removal rate of 810 g N/m 3 ⋅d and organic removal rates of 4,440 g COD/m 3 ⋅d. Scanning electron microscopy observations and 16S rRNA gene amplicon sequencing showed that phylum Bacillota was dominant in the final cultivated biofilms, accounting for 99.98% and 100% of total bacteria in the first and second reactors, respectively. The entrapment of biomass within the media supports bacterial development and enhances the retention of biomass in moving bed biofilm reactors.

  • Open Access

    Adsorption of Lead and Cobalt from Aqueous Solution Using Unmodified Date Palm Seeds: Kinetics and Isotherms

    by Nadia Almhana, Rasha Al-Saedi, Ishraq Abaas, Israa M. Al-Tameemi

    The ongoing pollution of water with heavy metals and the costly treatment methods have raised the need to search for an alternative treatment approach. In this work, a batch adsorption experiment using unmodified date palm seeds (UDPS) was conducted to investigate the effects of contact time, pH, adsorbent dose, and initial concentration on the removal rates of cobalt and lead from aqueous solution. Freundlich and Langmuir isotherms, as well as the kinetics of Pseudo-First- and second-order adsorption models, were also assessed. The results showed that equilibrium was reached at a 90-minute contact time, achieving the highest removal efficiencies of Co+2 and Pb+2 at pH 6, an adsorbent dose of 0.5 g, and initial Co+2 and Pb+2 concentrations of 10 mg/L, with maximum uptake potentials of 0.9 and 0.89 mg/g, respectively. Lead adsorption fitted slightly better to the Freundlich isotherm than to the Langmuir isotherm, whereas Co adsorption over the Langmuir isotherm. Regarding the kinetics of adsorption, the Pseudo-second order model better represented Co+2 and Pb+2 than the Pseudo-first-order model. FTIR results illustrate peaks at 3250 cm-1 and 3413 cm-1 for Co and Pb, respectively, corresponding to O=H stretching mode on the adsorbent surfaces.


  • Open Access

    Agricultural Wastes Derived Activated Carbon for the Removal of Iron from Car-Wash Wastewater

    by Tasnim Fahim Chyad, Zaman Ageel Hammood, Rasha Al-Saedi

    Over the past few decades, car-washing centres have increased due to the increase in the number of vehicles. Car-wash effluents are highly polluted with non-biodegradable, toxic, and carcinogenic heavy metals, including iron, lead, chrome, cadmium, and zinc. The focus in this study is on iron removal from car-wash wastewater due to its toxicity to the food chain, health, and environment. In comparison with the costly wastewater treatment technologies, adsorption is a widespread, simple, and cheap method that has been applied for the metal removal from car-wash wastewater. Since the conversion of agricultural waste into valuable sorbents is a renewable and eco-friendly approach, activated carbon was used in this research to assess iron removal performance from car-wash wastewater applying the adsorption technique. The impact of the following parameters: contact time (0 min to 120 min), iron concentration (8 mg/L to 14 mg/L), dose of adsorbent (0.2 g to 1 g per 25 mL wastewater), and pH (4 to 10) on the adsorption efficiency of activated carbon was studied. Fe was efficiently removed (98 %) at the optimum values of contact time 120 min, concentration 12 mg/L, dose 1 g, and pH 8, respectively. The investigated parameters (particularly dose of adsorbent and pH) need to be studied in a broader range as they did not show a potential difference in terms of iron removal efficiencies. Turbidity, TDS, and TSS were removed from car-wash wastewater after 2 hours of contact time, with removal efficiencies of 88 %, 75 %, and 55 % respectively. Effluent characteristics of car-wash stations are usually variable due to the differences in the amount of dirt from vehicles, size and number of washed vehicles, and type of used detergents.


  • Open Access

    Copper(II) Removal from Wastewater Using Pine Cone Derived Activated Carbon

    by Tasnim Fahim Chyad, Rasha Al-Saedi, Zaman Ageel Hammood

    Inappropriate disposal of wastewater including heavy metals may lead to serious public health problems. Among conventional wastewater treatment methods, adsorption is the preferred treatment technique, due to its advantages such as cheapness, simplicity, and flexibility in design and operation. In recent years, there has been an urgent need toward the production of low-cost alternatives to the commercial activated carbon which has a greater adsorption capacity with high porous and large surface area. In this experiment, activated carbon that derived from pine cone (PCAC) has been investigated as a new adsorbent to remove copper(II) ion from wastewater. The adsorption process of copper(II) ion from aqueous solution was carried out in a batch mode to study the effects of adsorbent dose (0.5 g/50 mL - 2 g/50 mL), initial pH (2-8), and initial concentrations (5 mg/L - 20 mg/L). The results indicated that activated carbon obtained from pine cone was an efficient adsorbent for the copper removal from the aqueous solution. Removal of copper ion from aqueous solution was dependent on the adsorbent dosage, pH, and initial Cu concentration, achieving maximum adsorption efficiency (99 %) at 2 g/50 mL, 6, and 20 mg/L, respectively.


  • Metal (Fe, Mn, and Cu) Removal from Synthetic Wastewater Using Modified Rice Husk in Fixed-Bed Columns

    by Rasha Al-Saedi, Zaman Ageel Hammood, Tasnim Fahim Chyad

    Laboratory-scale fixed bed columns were designed and monitored to compare the mobility and removal of copper (Cu), manganese (Mn), and iron (Fe) from industrial wastewater using chemically modified rice husk (main filter medium). The first and third beds (A and C) were treated with sodium carbonates and phosphates, respectively, while the second bed (B) was rice husk ash. During the study, changes in the concentrations of these metals were monitored and measured for all treatments under an influent flow rate and hydraulic loading rate of 0.00288 m3/d and 0.508 m3/m2 d, respectively. Parameters that may influence the mobilization and removal rate of metals, including Redox and pH, were also monitored and measured. The experiment was conducted under ambient temperatures with redox potentials and pH ranging from −50 to 200 mV and 6.5 to 12, respectively. An accumulation in the Fe and Mn concentrations occurred during the first 6 weeks of system operation; a decline thereafter was noticed with Fe and Mn effluents of 28, 20, 15 mg/L and 29, 16, and 139 mg/L for treatments A, B, and C, respectively. There was however a stable decline in the Cu concentrations over time with a final effluent of 14 mg/L for all treatments. Under redox and pH ranging from slight reduction to oxidation and strong alkaline to acidic conditions, respectively, satisfactory Fe removal was accomplished through both A and C treatments, while a better Mn removal was achieved with A rather than C treatment. A greater removal of Cu was observed in A rather than B and C beds. It can be concluded that A was the best treatment among different modifications for Fe, Mn, and Cu removal from industrial wastewater. Furthermore, Redox potentials and pH were found to be imperative parameters controlling the mobilization and removal dynamics of Fe, Mn, and Cu.


  • Open Access

    Adsorption Performance of Dyes Over Zeolite for Textile Wastewater Treatment

    by Zaman Ageel Hammood, Tasnim Fahim Chyad, Rasha Al-Saedi

    Removal of textile dyes from wastewater have recently attracted much attention, due to the toxicity, difficult visibility, and thereby the negative consequences on the aqueous environment. Therefore, there have been diverse promising new techniques such as adsorption for dyes removal from industrial wastewater. Compared to the highly cost treatment techniques, removal of dyes using the adsorption process is relatively simple and requires less cost. Synthetic zeolite was used in this research as a high capacity nano-adsorbent for the removal of reactive dyes from coloured wastewater. The impact of main parameters: dose of adsorbent (0.0025 to 0.02 g), pollutant concentration (25 to 200 mg/L), contact time (10 to 120 minutes), degree of agitation (25 and 300 rpm), and solution pH (2 to 8) on adsorption performance of the synthesised zeolite was investigated. The optimum values of these parameters to remove dyes efficiently at 90 % removal were 0.02 g, 200 mg/L, 80 min, 300 rpm, and 6-7 respectively. Also, two models were evaluated, the Langmuir and Freundlich isotherms. Langmuir isotherm was more efficient for representing the data than the Freundlich. The results of the Langmuir isotherm gave K L = 0.08 L/mg, q m = 6.02 mg/g, and R 2 = 0.98, which fitted to the adsorption data of zeolite. Reactive dye adsorption by synthetic zeolite is a vital tool in identifying the fate of dye removal from industrial wastewater treatment plants.


  • Open Access

    Ammonium Adsorption onto a Contaminated Soil-Water Environment Amended with Organic Matter

    by Rasha Al-Saedi, Zaman Ageel Hammood, Tasnim Fahim Chyad

    In this research, the ability of calcareous soil to absorb ammonium was investigated and the effect of compost amendment as a natural organic source on ammonium adsorption was also studied. pH, dissolved ammonium concentrations, ammonium adsorption capacity, and cation exchangeable capacity for...