RJRichard C. Jaeger

Richard C. Jaeger

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Richard C. Jaeger has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Measurement of the Temperature Dependence of the Piezoresistive Coefficients of 4H Silicon Carbide

    by Jun Chen, Jeffrey C. Suhling, Richard C. Jaeger

    Piezoresistive stress sensors on silicon were developed for measuring in-situ stresses in electronic packages, but due to its relatively low bandgap energy, the upper temperature range of silicon is limited. Stress sensors made with wide bandgap semiconductors such as 4H silicon carbide (4H-SiC) offer the advantage of much higher temperature operation [1] and can be utilized to monitor stresses in high-voltage, high-power SiC devices. The piezoresistive behavior of such sensors is characterized by piezoresistive (pi) coefficients, which must be calibrated before the stress measurement. In the prior study [2], the piezoresistive coefficients of 4H-SiC were calibrated only at room temperature, but 4H-SiC tends to be operated at high temperature. Thus, the piezoresistive coefficients under different temperatures are required.This work focuses on experimental study of the piezoresistive coefficients at different temperatures, from 300k to 450k. Calibration has been performed using four-point bending method with strip on flex circuit [3] specimen. A special four-point bending apparatus integrated into an environmental chamber is utilized.


  • Corrections to “First-Order Piezoresistive Coefficients of Lateral NMOS FETs on 4H Silicon Carbide” [Aug 19 6037-6045]

    by Richard C. Jaeger, Jun Chen, Jeffrey C. Suhling, Leonid Fursin

    We recently realized that the basic piezoresistivity matrix for 4H-SiC in the original paper [1] was not correct [2, 3]. The matrix and subsequent results are corrected here.


  • First- and Second-Order Piezoresistive Coefficients of CMOS FETs From Strong Into Weak Inversion

    by Richard C. Jaeger, Jeffrey C. Suhling

    For many years, researchers have noted that the stress response of MOS transistors exhibits strong deviations from a pure mobility behavior as the devices exit strong inversion, but there has been no easily accessible stress model that sensor designers can use in the design of their devices. In this work, generalized piezoresistance coefficients are presented that provide continuous modeling of the stress dependencies of CMOS FETs from weak into strong inversion. The models presented here incorporate both standard mobility variations plus the additional impact of threshold voltage changes on the stress responses in all regions of operation. The theory predicts both first-and second-order longitudinal and traverse piezoresistive coefficients for PMOS and NMOS devices that are verified with experimental results. The threshold voltage variations represent common-mode terms, so orthogonal differential pairs of MOSFETs can still be utilized to directly measure the important mobility components of the overall stress response, and the impact of the threshold voltage terms on sensor circuits may be reduced with differential design.


  • Piezoresistive Theory for 4H Silicon Carbide Stress Sensors on Four-Degree Off-Axis Wafers

    by Jun Chen, R. C. Jaeger, J. C. Suhling

    Piezoresistive stress sensors have been shown to be a powerful tool for experimental evaluation of die stress distributions. Silicon Carbide (SiC) wide bandgap semiconductors are promising materials for development of high temperature power electronics. In the past, the analysis and design of stress sensors on silicon carbide have assumed that the wafer surface is aligned with the crystallographic axes. However, 4H silicon carbide wafers are produced with a four-degree off-axis cut to ensure high-quality homoepitaxial growth, so that the tilted wafer surface does not perfectly coincide with the fundamental crystallographic axis. Thus, the prior “on-axis” theory is an approximation, and errors in piezoresistive theory caused by such tilted wafer plane need to be discussed. These errors can affect both the results from calibration experiments as well as the stresses extracted during application of sensor rosettes. This paper discusses the theory and extraction of piezoresistive coefficients for 4H-SiC silicon carbide materials in the presence of off-axis starting wafers. Coordinate transformations for the piezoresistive coefficients are reviewed, the required direction cosines between the new rotated axes and the ideal axes are discussed, and the 6 × 6 matrix of piezoresistive coefficients (π-matrix) for the on-axis and off-axis cases are calculated. Many of the elements of the ideal on-axis π-matrixes are zero. In contrast, the off-axis is completely filled with non-zero values indicating additional coupling, particularly among the shear coefficients. Examples of the overall impact of these new terms on calibration and stress measurement are discussed.


  • First-Order Piezoresistive Coefficients of Lateral NMOS FETs on 4H Silicon Carbide

    by Richard C. Jaeger, Jun Chen, Jeffrey C. Suhling, Leonid Fursin

    Stress dependent properties and modeling of lateral enhancement-mode NMOS FETS on 4H silicon carbide (4H-SiC) are described in detail for a wide range of bias conditions. NFET stress response is shown to include a strong threshold voltage component in addition to the expected mobility component, and a theoretical model for the stress dependencies closely matches the measured data. Values of the longitudinal and transverse piezoresistive coefficients are extracted from linear region measurements of the MOS transistors as a function of gate drive for the both crystallographic and chip coordinate systems. At low gate drive, threshold variations become much more important than the classic mobility terms, whereas high gate drive is utilized to extract the mobility terms from the data. Design of a four-transistor temperature compensated stress sensor rosette that requires a value of only one combined piezoresistive coefficient is also presented.


  • Erratum: “Four-Wire Bridge Measurements of Silicon van der Pauw Stress Sensors” [ASME J. Electron. Packag., 2014, 136(4), p. 041014; DOI: 10.1115/1.4028333]

    by Richard C. Jaeger, Mohammad Motalab, Safina Hussain, Jeffrey C. Suhling

    The conjecture discussed in the referenced paper was backed up by measurements and simulation results, but not mathematically proven. A proof based on impedance parameter reciprocity is presented, and a sign error is corrected.


  • Four-Wire Bridge Measurements of Silicon van der Pauw Stress Sensors

    by Richard C. Jaeger, Mohammad Motalab, Safina Hussain, Jeffrey C. Suhling

    Under the proper orientations and excitations, the transverse output of rotationally symmetric four-contact van der Pauw (VDP) stress sensors depends upon only the in-plane shear stress or the difference of the in-plane normal stresses on (100) silicon. In bridge-mode, each sensor requires only one four-wire measurement and produces an output voltage with a sensitivity that is 3.16 times that of the equivalent resistor rosettes or bridges, just as in the normal VDP sensor mode that requires two separate measurements. Both numerical and experimental results are presented to validate the conjectured behavior of the sensor. Similar results apply to sensors on (111) silicon. The output voltage results provide a simple mathematical expression for the offset voltage in Hall effect devices or the response of pseudo Hall-effect sensors. Bridge operation facilitates use of the VDP structure in embedded stress sensors in integrated circuits.


  • An 8–18GHz 0.18W wideband recursive receiver MMIC with gain-reuse

    by Desheng Ma, Fa Foster Dai, Richard C. Jaeger, J. David Irwin

    This paper presents an 8-18 GHz wideband receiver with superheterodyne topology. In order to save power, both RF and IF signals share the tunable transconductance stage. The IF output of the first mixer is fed to its tunable input stage for IF amplification in a recursive manner, which significantly enhances the gain tuning without increasing the power. The wideband receiver MMIC is implemented in a 0.13 mum SiGe BiCMOS technology and achieves 6.7-7.8 dB noise figure (NF). The average voltage gain of the receiver is measured as 53 dB maximum with 20 dB continual tuning and 36 dB discrete tuning. The average output P1dB is measured as -10 dBm at maximum gain. The receiver dissipates 180 mW with 2.2 V power supply. To the authors' best knowledge, this is the first fully integrated single-chip receiver MMIC with the coverage of the entire X-band and Ku-band realized on a commercial SiGe process.

  • Delta-Sigma Modulation in Direct Digital Frequency Synthesis

    by Dayu Yang, Weining Ni, Foster F. Dai, Yin Shi, Richard C. Jaeger

    This paper presents comparisons of various DeltaSigma modulations in direct digital frequency synthesis. DeltaSigma modulators such as MASH, feedforward, feedback and error feedback have been implemented in both phase and frequency domains in a CMOS DDS. The DDS prototype is fabricated in a 0.35mum CMOS technology with core area of 1.7times2.1 mm and total 75 mA current. Measured DDS output demonstrates that frequency domain DeltaSigma modulation achieves better SFDR and SINAD than phase domain AE modulation