D. A. Sumskoy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
D. A. Sumskoy has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Lilia Kh. Zagorodnyuk
Belgorod State Technological University named after V.G. Shukhov
4 shared publications - D. S. Makhortov
Belgorod State Technological University named after V.G. Shukhov
2 shared publications - Vladislav Ryzhikh
Belgorod State Technological University named after V.G. Shukhov
2 shared publications - Daria Alexandrovna Sinebok
Department of theoretical and applied chemistry, Belgorod State Technological University Named after V.G. Shukhov, 308012 Belgorod, Russia
1 shared publication - Nikolay Shapovalov
Belgorod State Technological University named after V.G. Shukhov
1 shared publication - S. V. Zolotykh
Belgorod State Technological University named after V.G. Shukhov
1 shared publication
Latest Publications
- Open Access
- 15 September 2022
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 19 (4) , 584-596
Cement and claydite dust binding compositions
Introduction. The article presents the production results for binder compositions of the optimal proportion based on Portland cement and claydite waste – claydite dust. The granulometric composition studies have been conducted, test results for binder compositions of different proportions are presented: cement – claydite dust, jointly mechanically activated in a vibrating mill. The binder compositions with a wide range of use have been developed and determined. Using the electron microscopy method, microphotographs of cement stones chips made from Portland cement and different contents of claydite dust, which have been mechanically activated in a vibrating mill, were taken. There is active overgrowth of open pores in cement stones obtained from binder compositions by neoplasms of various sizes.After the use of claydite dust as a raw mix, the structure of the composite is compacted.Materials and methods. ЦЕМ0 52.5N Portland cement (GOST 31108-2020) produced by ZAO Belgorodskii Cement and claydite dust, the waste of claydite dust production, were used in the work. The mechanical activation was performed by grinding in a vibrating mill. The normal density was determined using the Vic’s device according to GOST. The granulometric composition was studied using the AnalyssetteNanoTecplus device. The microstructure was studied using a high-resolution scanning electronic TESCAN MIRA 3 LMU microscope. In order to construct diffractograms, the ARL X’TRA Thermo Fisher Scientific device was used.Results. The binding composition of the optimal proportion of claydite dust demonstrates an increase in strength characteristics, there is a compaction of the cement stone structure compared to ordinary Portland cement.Discussion and conclusions. The use of waste from the production of claydite – claydite dust as a mineral filler of the binder composition makes it possible to save expensive Portland cement, while increasing the strength characteristics of the binder composition.
- 15 September 2022
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 19 (4) , 584-596
Open AccessCement and claydite dust binding compositions
Introduction. The article presents the production results for binder compositions of the optimal proportion based on Portland cement and claydite waste – claydite dust. The granulometric composition studies have been conducted, test results for binder compositions of different proportions are presented: cement – claydite dust, jointly mechanically activated in a vibrating mill. The binder compositions with a wide range of use have been developed and determined. Using the electron microscopy method, microphotographs of cement stones chips made from Portland cement and different contents of claydite dust, which have been mechanically activated in a vibrating mill, were taken. There is active overgrowth of open pores in cement stones obtained from binder compositions by neoplasms of various sizes.After the use of claydite dust as a raw mix, the structure of the composite is compacted.Materials and methods. ЦЕМ0 52.5N Portland cement (GOST 31108-2020) produced by ZAO Belgorodskii Cement and claydite dust, the waste of claydite dust production, were used in the work. The mechanical activation was performed by grinding in a vibrating mill. The normal density was determined using the Vic’s device according to GOST. The granulometric composition was studied using the AnalyssetteNanoTecplus device. The microstructure was studied using a high-resolution scanning electronic TESCAN MIRA 3 LMU microscope. In order to construct diffractograms, the ARL X’TRA Thermo Fisher Scientific device was used.Results. The binding composition of the optimal proportion of claydite dust demonstrates an increase in strength characteristics, there is a compaction of the cement stone structure compared to ordinary Portland cement.Discussion and conclusions. The use of waste from the production of claydite – claydite dust as a mineral filler of the binder composition makes it possible to save expensive Portland cement, while increasing the strength characteristics of the binder composition.
- 29 March 2021
- Published by Springer Nature
- p. 22-28
Method of Extrusion Granulation of Aggregates for the Preparation of Filling Mixtures
- 29 March 2021
- Published by Springer Nature
- p. 22-28
Method of Extrusion Granulation of Aggregates for the Preparation of Filling Mixtures
- 31 July 2020
- Published by Springer Nature
- p. 253-259
Composite Binders Based on Dust of Electric Filters
- 31 July 2020
- Published by Springer Nature
- p. 253-259
Composite Binders Based on Dust of Electric Filters
- Open Access
- 4 July 2019
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 16 (3) , 323-333
EFFECTIVE HEAT-PROTECTIVE SYSTEM WITH THE USE OF THERMAL INSULATING SOLUTION OF REDUCED DENSITY
Introduction. The manuscript is devoted to the actual problem of thermal insulation of buildings and structures. The paper presents a developed low-density insulation solution with improved heatengineering characteristics. The aim of the work is to increase the efficiency of the heat-shielding system using a low-density heat-insulating solution.Methods and materials.The authors carried out tests at the site of heat engineering control of LLC «Intellect-service-ZBK-1» to determine the resistance to heat transfer of the enclosing structure.Results.The construction of the wall system consisting of the «Aerobel» D500 gas-silicate block (625×200×250 mm) and made on a low-density heat-insulating masonry mortar, as well as with the use of a heat-insulating mortar and a universal «Moutrical» energy-efficient coating allowed increasing actual reduced heat transfer resistance from 0.9 to 1.4 (m2 ·K) / W (by 36%).Discussion and conclusions.Laboratory research and field tests that meet the requirements of state standards and that develop low-density heat-insulating plaster demonstrate the low-density heatinsulating solution, which indicates the feasibility in thermal insulation of buildings and structures. The authors achieve special economic and ecological effect in connection with the use of local raw materials and waste production of expanded perlite sand.
- 4 July 2019
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 16 (3) , 323-333
Open AccessEFFECTIVE HEAT-PROTECTIVE SYSTEM WITH THE USE OF THERMAL INSULATING SOLUTION OF REDUCED DENSITY
Introduction. The manuscript is devoted to the actual problem of thermal insulation of buildings and structures. The paper presents a developed low-density insulation solution with improved heatengineering characteristics. The aim of the work is to increase the efficiency of the heat-shielding system using a low-density heat-insulating solution.Methods and materials.The authors carried out tests at the site of heat engineering control of LLC «Intellect-service-ZBK-1» to determine the resistance to heat transfer of the enclosing structure.Results.The construction of the wall system consisting of the «Aerobel» D500 gas-silicate block (625×200×250 mm) and made on a low-density heat-insulating masonry mortar, as well as with the use of a heat-insulating mortar and a universal «Moutrical» energy-efficient coating allowed increasing actual reduced heat transfer resistance from 0.9 to 1.4 (m2 ·K) / W (by 36%).Discussion and conclusions.Laboratory research and field tests that meet the requirements of state standards and that develop low-density heat-insulating plaster demonstrate the low-density heatinsulating solution, which indicates the feasibility in thermal insulation of buildings and structures. The authors achieve special economic and ecological effect in connection with the use of local raw materials and waste production of expanded perlite sand.