LZLilia Kh. Zagorodnyuk

Lilia Kh. Zagorodnyuk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lilia Kh. Zagorodnyuk has a total of 63 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    THE EFFECT OF MECHANICAL ACTIVATION IN A ROTARY BALL MILL ON THE PROPERTIES OF BINDER COMPOSITIONS WITH THE ADDITION OF VOLCANIC SAND

    by L. Zagorodnyuk, D. Chernukha, G. Ivanov, M. Sorokin

    The paper investigates composite binders based on Portland cement and volcanic sand, subjected to mechanical activation in a rotary ball mill. The rational parameters of grinding (10, 30 and 50 minutes) and the filler content (10-30%) were determined. It was found that under optimal conditions, the specific surface area reaches 847.7 m2/kg, which is 2.83 times higher than that of commercial cement. The maximum compressive strength after 28 days (82.7 MPa) was obtained for a composition with 10% sand after 10 minutes of activation. The possibility of saving Portland cement up to 20-30% is shown, depending on the grinding mode. Mechanical activation in a rotary ball mill intensifies the hydration processes, however, with prolonged grinding (50 min), an ambiguous effect on strength characteristics is observed, depending on the proportion of filler. The resulting composites are recommended for the production of general-purpose and special-purpose concrete.

  • Open Access

    EFFECT OF MECHANOACTIVATION IN A VIBRATION MILL ON THE PROPERTIES OF BINDING COMPOSITIONS WITH THE ADDITION OF VOLCANIC SAND

    by D. Chernukha, L. Zagorodnyuk, G. Ivanov

    The paper examines composite binders based on Portland cement and volcanic sand, subjected to mechanical activation in a vibrating mill. Rational grinding parameters (10, 30, and 50 minutes) and filler content (10-30%) were determined. It was found that under optimal conditions, the specific surface area reaches 731.2 m2/kg, and the compressive strength increases to 90.34 MPa after 28 days, which is 77.8% higher than that of commercial cement. Laser granulometry and X-ray phase analysis revealed the hardening mechanisms associated with the amorphization of the structure, a decrease in the average diameter of the particles and the formation of additional hydrosilicate phases. The possibility of saving Portland cement up to 30% without loss of strength characteristics is shown


  • Influence of Waste Glass Powder on the Properties of Vitrified Bricks Based on Loess

    by V. S. Lesovik, L. Kh. Zagorodnyuk, Z. B. Djumaniyazov, D. Z. Boltabayev, Sh. X. Xujyazov, Yo. S. Ruzimov

  • Open Access

    STUDYING THE PROCESS OF MIXING THE MAIN COMPONENTS OF AN ADSORBENT HYGIENIC PRODUCTS

    by L. Zagorodnyuk, V. Bogdanov, E. Kikalishvili, Gaziev H. H., D. Sumskoy

    The results of research on the study of the mixing process to develop the basic composition of an adsorbent hygienic product for keeping animals and birds in accordance with sanitary standards are presented. The possibility of using a rotary ball mill as the most effective apparatus for grinding and mixing and a turbulent mixer, ensuring high homogeneity when mixing the main ingredients of mixtures, is investigated. In result of studying the processes of mixing the main ingredients in the preparation of an adsorbent hygiene product in various mixing units, an effective basic composition of an adsorbent hygiene product is obtained. Moreover, the components chalk M-5, attapulgite and synthetic amorphous silicon dioxide, obtained by mixing in a turbulent mixer and corresponding to the required specific surface area of 12000 cm2/g, which will provide the necessary sorption capacity and thereby ensure a reduction in pathogenic microflora in places where farm animals and poultry are kept. The developed basis of an adsorbent hygienic powder product, due to its significant specific surface area, will provide a high degree of moisture absorption and create the required level of sanitary and hygienic conditions for keeping animals and birds. Creating a favorable climate for keeping farm animals and poultry will significantly prevent the proliferation of bacteria, which will entail a significant reduction in the consumption of antibiotics when raising farm animals, reduce the level of unpleasant odors, and provide a dry environment for keeping animals and birds


  • Open Access

    Теплоизоляционные растворы с использованием вермикулита и их оптимизация

    by Лилия Хасановна Загороднюк, Саад Аль Мамури Кхалил Шадид, Дмитрий Алексеевич Сумской, Андрей Леонидович Бочарников

    Разработка эффективных составов и получение теплоизоляционных материалов с высокими теплозащитными показателями актуальна и требует глубокого изучения. В статье изложены результаты оптимизации состава теплоизоляционного раствора, приготовленного на композиционном вяжущем, вспученного вермикулита как заполнителя и различных функциональных добавок. Приведены результаты оптимизации состава вяжущей композиции на основе портландцемента и вермикулита суперпластификатором MELMENT F10. Установлена оптимальная дозировка суперпластификатора, обеспечившая плотность композиционного вяжущего 1933 кг/м3 при прочности 58,2 МПа. Подобраны функциональные добавки для обеспечения требуемых физико-механических и эксплуатационных свойств теплозащитного раствора. Изучено влияние на плотность и прочность состава теплоизоляционного раствора различных дозировок порообразователя Esapon 1214, суперпластификатора Melment F10, редиспергирующего порошка Vinnapas LL 4042 H. Получено уравнение регрессии для средней плотности и средней прочности теплоизоляционных растворов. Полученные уравнения регрессии и номограммы, построенные по ним, позволяют оптимизировать технологический процесс и эффективно им управлять. Методом математического планирования эксперимента подобран состав теплоизоляционного раствора, имеющий минимальное значение по плотности 490 кг/м3 при прочности на сжатие 2,3 МПа. В ряду современных штукатурных смесей для теплоизоляционных штукатурных растворов разработанные составы характеризуются улучшенными теплотехническими свойствами при оптимальных технико-экономических показателях.


  • Open Access

    Mixing of heat-insulating mixtures in pneumatic mixer with spiral energy carrying tube

    by Al Mamuri Saad Khalil Shadid, O. M. Shemetova, L. Kh. Zagorodnuk, A. L. Bocharnikov

    Introduction. Mixing of dry components in mixers is one of the most important stages of any technological process in the manufacture of a composite material. To date, various technologies use a wide variety of mixing equipment, which is characterized by different principles of mixing and design solutions. Of particular interest for the preparation of high-quality and homogeneous mixtures for heat-insulating purposes is a pneumatic mixer with a spiral energycarrying tube. The article presents the results of studies using the method of mathematical planning of the fullfactor ПФЭЦКРП24 experiment, which makes it possible to most adequately assess the ongoing processes while minimizing systematic errors.Materials and methods. In the work, ЦЕМ 0 42,5Н ГОСТ 31108–2020 Portland cement with a specific surface area of 308 m2 / kg, sand of the Volsky deposit were used as raw materials for testing. Expanded vermiculite obtained as a result of heat treatment of natural vermiculite at a temperature of about 700°C was used as a light filler.Results. Heat-insulating mixtures prepared in a pneumatic mixer with a spiral energy-carrying tube ensure the production of heat-insulating mortars with stable density values of 1420 kg/m3, having sufficient compressive strength of 3.3 MPa, and guarantee high heat-shielding properties in building structures.Conclusion. The developed design and the conducted studies made it possible to establish the high efficiency of the proposed mixer, which provides a uniform distribution of the particles to be mixed, high homogenization and the creation of conditions for accelerating the physicochemical interactions in the created mixture with subsequent mixing of the prepared mixture with water and the formation of the required internal structure of the created composites.

  • Open Access

    BINDING COMPOSITIONS USING VERMICULITE FOR HEAT PROTECTIVE SOLUTIONS

    by Saad Al Mamouri, L.H. Zagorodnyuk, D. Sumskoy, A. Bocharnikov, O. Shemetova

    Цементный камень из вяжущих композиций создается за счет формирования пространственного каркаса, создаваемого пористым минеральным наполнителем, который за счет высокой дисперсности занимает значительный пространственный объем, и на этом минеральном наполнителе, как на подложках, формируется кристаллическая структура, создаваемая гидросиликатами и гидроалюминатами кальция, постепенно наращивая как бы вторичный каркас кристаллическими новообразованиями на тонкодисперсных вермикулитовых зернах-пластинах. Разработанное вяжущее обладает пористой структурой за счет введения вермикулитового наполнителя, что обеспечивает снижение теплопроводности создаваемого композита. Применение полученных вяжущих композиций, приготовленных из смеси портландцемента и вермикулита, в сочетании с пористым заполнителем-вспученным вермикулитом, позволит получить теплоизоляционный раствор с высокими теплозащитными показателями и гарантированной прочностью. Ключевые слова: вспученный вермикулит, вяжущая композиция, теплозащитные растворы, портландцемент, низкая плотность, микроструктура. Введение. В последние годы возрос интерес к созданию материалов, обладающих высокими теплозащитными свойствами, а также устойчивых к высоким температурам. Стойкость строительных материалов к воздействию высоких температур имеет огромное значение, особенно во время пожара. Штукатурные растворы с повышенной стойкостью к повышенным температурам могут обеспечить надежную пожарную защиту. Одним из способов повышения теплозащитных и термостойких материалов является использование в теплоизоляционных растворах эффективных заполнителей, имеющих пористое строение и обладающих термостойкими свойствами. В результате многолетних исследований российскими и зарубежными учеными накоплен значительный положительный опыт применения при создании легких растворов и бетонов различных пористых заполнителей, в частности, пемзы [1], диатомита [2], вулканического туфа, вспученного вермикулита [3], вспученного перлита [4-7], а также вспученной глины [8]. Особую значимость в современных условиях представляет


  • Open Access

    Cement and claydite dust binding compositions

    by D. S. Makhortov, L. Kh. Zagorodnyuk, N. A. Shapovalov, D. A. Sumskoy

    Introduction. The article presents the production results for binder compositions of the optimal proportion based on Portland cement and claydite waste – claydite dust. The granulometric composition studies have been conducted, test results for binder compositions of different proportions are presented: cement – claydite dust, jointly mechanically activated in a vibrating mill. The binder compositions with a wide range of use have been developed and determined. Using the electron microscopy method, microphotographs of cement stones chips made from Portland cement and different contents of claydite dust, which have been mechanically activated in a vibrating mill, were taken. There is active overgrowth of open pores in cement stones obtained from binder compositions by neoplasms of various sizes.After the use of claydite dust as a raw mix, the structure of the composite is compacted.Materials and methods. ЦЕМ0 52.5N Portland cement (GOST 31108-2020) produced by ZAO Belgorodskii Cement and claydite dust, the waste of claydite dust production, were used in the work. The mechanical activation was performed by grinding in a vibrating mill. The normal density was determined using the Vic’s device according to GOST. The granulometric composition was studied using the AnalyssetteNanoTecplus device. The microstructure was studied using a high-resolution scanning electronic TESCAN MIRA 3 LMU microscope. In order to construct diffractograms, the ARL X’TRA Thermo Fisher Scientific device was used.Results. The binding composition of the optimal proportion of claydite dust demonstrates an increase in strength characteristics, there is a compaction of the cement stone structure compared to ordinary Portland cement.Discussion and conclusions. The use of waste from the production of claydite – claydite dust as a mineral filler of the binder composition makes it possible to save expensive Portland cement, while increasing the strength characteristics of the binder composition.


  • Granular materials based on expanded sands and their production waste

    by O. Miryuk, L.H. Zagorodnyuk

    The article presents the results of studies of granular materials obtained by non-firing technology. For the formation of granules, composite cement and magnesia binders containing waste products of expanded perlite and expanded clay are proposed. Mechanical activation of composite binders intensifies the processes of hydration and structure formation, contributes to increasing the strength of materials. The combination of a binder with a filler in the form of waste from the production of porous aggregates ensures a decrease in the density of the binder, the formation of a finely dispersed porous structure of the composite material, the formation of stable hydrates. The porous structure of the granules is provided by the use of porous sand to form the core of the granules. Studies of the structure of granules by electron microscopy revealed that the reliable adhesion of particles of porous sand with a composite binder stone provides high strength of porous granular materials. Cement granules based on expanded perlite sand are characterized by a density of 300 – 400 kg/m3 and a compressive strength of 1.8 – 2.6 MPa. Magnesia granules based on expanded clay sand have a density of 450 – 500 kg/m3 and compressive strength of 3.5 – 5.7 MPa. The work is aimed at creating effective building materials using resource-saving technology, at the rational use of production waste.


  • Open Access

    Сomposite binders for 3d additive technologies

    by L. Kh. Zagorodnuk, M. Yu. Elistratkin, D. S. Podgornyi, Saad Khalil Shadid Al Mamuri

    Introduction. In recent years, there has been an active development of 3D additive technologies. This trend could not but affect the construction industry. However, printing using plastics and other organic compounds differs significantly in its technological features from printing with building compounds. Concrete and mortars used in layer-by-layer printing must have a number of technological properties, such as sufficient viscosity for extrusion by an extruder, low mobility to maintain geometry after laying, high setting speed and strength after hardening. Currently, there are a number of compositions that meet these requirements, however, they, as a rule, are not distinguished by high strength and require a wide raw material base, which may not be available in field printing conditions. As a result, it is necessary to expand the range of building materials for 3D printing, suitable for the above criteria, as well as satisfying economic indicators.Materials and methods. Research has been carried out using physical and mechanical tests, X-ray phase analysis and electron microscopy on the effect of finely ground mineral additives on the microstructure and hardening processes of composite binders with various dosages of functional additives.Results. The results of studies on the production of composite binders for 3D additive technologies using Portland cement and man-made waste - waste of wet magnetic separation of the Stary Oskol electrometallurgical plant, modified with additives accelerators (Technonikol Master) and plasticizers (Polyplast PK-R) using mathematical planning and construction of mathematical models for composite binders with different hardening times are pesented.Conclusion. The efficiency of using the obtained composite binder has been proven, the use of which provides an increase in rheological properties, and also makes it possible to save expensive portland cement.