Seung Keun Song
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Seung Keun Song has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Gregory N. Parsons
Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, NC 27695, USA
6 shared publications - Hannah R. M. Margavio
Department of Chemical and Biomolecular Engineering, North Carolina State University, 911 Partners Way, Raleigh, North Carolina 27606, United States
2 shared publications - Jung-Sik Kim
Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, North Carolina 27695, United States
2 shared publications - Amanda Bednar
Department of Materials Science and Engineering, North Carolina State University 1 , Raleigh, North Carolina 27695, USA
1 shared publication - Amy Dowden
Department of Materials Science and Engineering, North Carolina State University 1 , Raleigh, North Carolina 27695, USA
1 shared publication - Annelies Delabie
Department of Chemistry, KU Leuven 1 , Celestijnenlaan 200F, Leuven 3001
1 shared publication
Latest Publications
- 24 February 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (5) , 1961-1971
HfO2 Area Selective Deposition via Substrate-Dependent Area Selective Atomic Layer Etching
- 24 February 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (5) , 1961-1971
HfO2 Area Selective Deposition via Substrate-Dependent Area Selective Atomic Layer Etching
- Open Access
- 28 December 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (24)
The influence of crystallographic texture on structural and electrical properties in ferroelectric Hf0.5Zr0.5O2
Ferroelectric (Hf,Zr)O2 thin films have attracted increased interest from the ferroelectrics community and the semiconductor industry due to their ability to exhibit ferroelectricity at nanoscale dimensions. The properties and performance of the ferroelectric (Hf,Zr)O2 films generally depend on various factors such as surface energy (e.g., through grain size or thickness), defects (e.g., through dopants, oxygen vacancies, or impurities), electrodes, interface quality, and preferred crystallographic orientation (also known as crystallographic texture or simply texture) of grains and/or domains. Although some factors affecting properties and performance have been studied extensively, the effects of texture on the material properties are still not understood. Here, the influence of texture of the bottom electrode and Hf0.5Zr0.5O2 (HZO) films on properties and performance is reported. The uniqueness of this work is the use of a consistent deposition process known as Sequential, No-Atmosphere Processing (SNAP) that produces films with different preferred orientations yet minimal other differences. The results shown in this study provide both new insight on the importance of the bottom electrode texture and new fundamental processing-structure–property relationships for the HZO films.
- 28 December 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (24)
Open AccessThe influence of crystallographic texture on structural and electrical properties in ferroelectric Hf0.5Zr0.5O2
Ferroelectric (Hf,Zr)O2 thin films have attracted increased interest from the ferroelectrics community and the semiconductor industry due to their ability to exhibit ferroelectricity at nanoscale dimensions. The properties and performance of the ferroelectric (Hf,Zr)O2 films generally depend on various factors such as surface energy (e.g., through grain size or thickness), defects (e.g., through dopants, oxygen vacancies, or impurities), electrodes, interface quality, and preferred crystallographic orientation (also known as crystallographic texture or simply texture) of grains and/or domains. Although some factors affecting properties and performance have been studied extensively, the effects of texture on the material properties are still not understood. Here, the influence of texture of the bottom electrode and Hf0.5Zr0.5O2 (HZO) films on properties and performance is reported. The uniqueness of this work is the use of a consistent deposition process known as Sequential, No-Atmosphere Processing (SNAP) that produces films with different preferred orientations yet minimal other differences. The results shown in this study provide both new insight on the importance of the bottom electrode texture and new fundamental processing-structure–property relationships for the HZO films.
- 22 August 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (8) , 082102
Mechanisms for undesired nucleation on H-terminated Si and dimethylamino-trimethylsilane passivated SiO2 during TiO2 area-selective atomic layer deposition
During TiO2 atomic layer deposition (ALD) using TiCl4 and H2O at ∼150 °C, nucleation proceeds rapidly on hydroxylated SiO2 but is inherently delayed on passivated surfaces such as H-terminated silicon (Si-H) and trimethylsilyl-passivated SiO2 (SiO2-TMS) formed using dimethylamino-trimethylsilane (DMA-TMS) as a small molecule inhibitor. In this work, we explore details of TiO2 nucleation on both Si-H and SiO2-TMS and show that the mechanisms leading to unwanted nuclei depend strongly on the passivation mechanism. Initial growth is observed as a function of ALD cycles using scanning electron microscopy to obtain average particle size, density, and overall surface coverage fraction. Also, average film thickness vs cycle is estimated using ellipsometry or Rutherford backscattering spectrometry. Data are compared to an analytical model that considers that either nucleation sites are present on the starting non-growth surface or sites are generated during the ALD process. On the Si-H surface, data and modeling indicate that nucleation occurs predominantly from a fixed number of nucleation sites present on the starting growth surface that start to immediately grow. However, on TMS-passivated SiO2, nucleation sites are predominantly generated during the growth process so that the density of nucleation sites increases as growth proceeds. Results indicate that nucleation sites are created when adsorbed ALD reactants become kinetically trapped on the SiO2-TMS surface. This demonstrates that mechanisms associated with unwanted nucleation during area-selective deposition (ASD) can depend on details of the surface passivation scheme, thereby providing insight to help to improve ASD strategies for advanced applications.
- 22 August 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (8) , 082102
Mechanisms for undesired nucleation on H-terminated Si and dimethylamino-trimethylsilane passivated SiO2 during TiO2 area-selective atomic layer deposition
During TiO2 atomic layer deposition (ALD) using TiCl4 and H2O at ∼150 °C, nucleation proceeds rapidly on hydroxylated SiO2 but is inherently delayed on passivated surfaces such as H-terminated silicon (Si-H) and trimethylsilyl-passivated SiO2 (SiO2-TMS) formed using dimethylamino-trimethylsilane (DMA-TMS) as a small molecule inhibitor. In this work, we explore details of TiO2 nucleation on both Si-H and SiO2-TMS and show that the mechanisms leading to unwanted nuclei depend strongly on the passivation mechanism. Initial growth is observed as a function of ALD cycles using scanning electron microscopy to obtain average particle size, density, and overall surface coverage fraction. Also, average film thickness vs cycle is estimated using ellipsometry or Rutherford backscattering spectrometry. Data are compared to an analytical model that considers that either nucleation sites are present on the starting non-growth surface or sites are generated during the ALD process. On the Si-H surface, data and modeling indicate that nucleation occurs predominantly from a fixed number of nucleation sites present on the starting growth surface that start to immediately grow. However, on TMS-passivated SiO2, nucleation sites are predominantly generated during the growth process so that the density of nucleation sites increases as growth proceeds. Results indicate that nucleation sites are created when adsorbed ALD reactants become kinetically trapped on the SiO2-TMS surface. This demonstrates that mechanisms associated with unwanted nucleation during area-selective deposition (ASD) can depend on details of the surface passivation scheme, thereby providing insight to help to improve ASD strategies for advanced applications.
- 25 June 2021
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 15 (7) , 12276-12285
Multimaterial Self-Aligned Nanopatterning by Simultaneous Adjacent Thin Film Deposition and Etching
Printed component sizes in electronic circuits are approaching 10 nm, but inherent variability in feature alignment during photolithography poses a fundamental barrier for continued device scaling. Deposition-based self-aligned patterning is being introduced, but nuclei defects remain an overarching problem. This work introduces low-temperature chemically self-aligned film growth via simultaneous thin film deposition and etching in adjacent regions on a nanopatterned surface. During deposition, nucleation defects are avoided in nongrowth regions because deposition reactants are locally consumed via sacrificial etching. For a range of materials and process conditions, thermodynamic modeling confirms that deposition and etching are both energetically favorable. We demonstrate nanoscale patterning of tungsten at 220 °C with simultaneous etching of TiO2. Area selective deposition (ASD) of the sacrificial TiO2 layer produces an orthogonal sequence for self-aligned patterning of two materials on one starting pattern, i.e., TiO2 ASD on SiO2 followed by W ASD on Si–H. Experiments also show capacity for self-aligned dielectric patterning via favorable deposition of AlF3 on Al2O3 at 240 °C with simultaneous atomic layer etching of sacrificial ZnO. Simultaneous deposition and etching provides opportunities for low-temperature bottom-up self-aligned patterning for electronic and other nanoscale systems.
- 25 June 2021
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 15 (7) , 12276-12285
Multimaterial Self-Aligned Nanopatterning by Simultaneous Adjacent Thin Film Deposition and Etching
Printed component sizes in electronic circuits are approaching 10 nm, but inherent variability in feature alignment during photolithography poses a fundamental barrier for continued device scaling. Deposition-based self-aligned patterning is being introduced, but nuclei defects remain an overarching problem. This work introduces low-temperature chemically self-aligned film growth via simultaneous thin film deposition and etching in adjacent regions on a nanopatterned surface. During deposition, nucleation defects are avoided in nongrowth regions because deposition reactants are locally consumed via sacrificial etching. For a range of materials and process conditions, thermodynamic modeling confirms that deposition and etching are both energetically favorable. We demonstrate nanoscale patterning of tungsten at 220 °C with simultaneous etching of TiO2. Area selective deposition (ASD) of the sacrificial TiO2 layer produces an orthogonal sequence for self-aligned patterning of two materials on one starting pattern, i.e., TiO2 ASD on SiO2 followed by W ASD on Si–H. Experiments also show capacity for self-aligned dielectric patterning via favorable deposition of AlF3 on Al2O3 at 240 °C with simultaneous atomic layer etching of sacrificial ZnO. Simultaneous deposition and etching provides opportunities for low-temperature bottom-up self-aligned patterning for electronic and other nanoscale systems.
- 8 September 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (10) , 105302
Effect of reactant dosing on selectivity during area-selective deposition of TiO2 via integrated atomic layer deposition and atomic layer etching
A key hallmark of atomic layer deposition (ALD) is that it proceeds via self-limiting reactions. For a good ALD process, long reactant exposure times beyond that required for saturation on planar substrates can be useful, for example, to achieve conformal growth on high aspect ratio nanoscale trenches, while maintaining consistent deposition across large-area surfaces. Area-selective deposition (ASD) is becoming an enabling process for nanoscale pattern modification on advanced nanoelectronic devices. Herein, we demonstrate that during area-selective ALD, achieved by direct coupling of ALD and thermal atomic layer etching (ALE), excess reactant exposure can have a substantially detrimental influence on the extent of selectivity. As an example system, we study ASD of TiO2 on hydroxylated SiO2 (Si–OH) vs hydrogen-terminated (100) Si (Si–H) using TiCl4/H2O for ALD and WF6/BCl3 for ALE. Using in situ spectroscopic ellipsometry and ex situ x-ray photoelectron spectroscopy, we show that unwanted nucleation can be minimized by limiting the water exposure during the ALD steps. Longer exposures markedly increased the rate of nucleation and growth on the desired non-growth region, thereby degrading selectivity. Specifically, transmission electron microscopy analysis demonstrated that near-saturated H2O doses enabled 32.7 nm thick TiO2 patterns at selectivity threshold S > 0.9 on patterned Si/SiO2 substrates. The correlation between selectivity and reactant exposure serves to increase fundamental insights into the effects of sub-saturated self-limiting surface reactions on the quality and effectiveness of ASD processes and methods.
- 8 September 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (10) , 105302
Effect of reactant dosing on selectivity during area-selective deposition of TiO2 via integrated atomic layer deposition and atomic layer etching
A key hallmark of atomic layer deposition (ALD) is that it proceeds via self-limiting reactions. For a good ALD process, long reactant exposure times beyond that required for saturation on planar substrates can be useful, for example, to achieve conformal growth on high aspect ratio nanoscale trenches, while maintaining consistent deposition across large-area surfaces. Area-selective deposition (ASD) is becoming an enabling process for nanoscale pattern modification on advanced nanoelectronic devices. Herein, we demonstrate that during area-selective ALD, achieved by direct coupling of ALD and thermal atomic layer etching (ALE), excess reactant exposure can have a substantially detrimental influence on the extent of selectivity. As an example system, we study ASD of TiO2 on hydroxylated SiO2 (Si–OH) vs hydrogen-terminated (100) Si (Si–H) using TiCl4/H2O for ALD and WF6/BCl3 for ALE. Using in situ spectroscopic ellipsometry and ex situ x-ray photoelectron spectroscopy, we show that unwanted nucleation can be minimized by limiting the water exposure during the ALD steps. Longer exposures markedly increased the rate of nucleation and growth on the desired non-growth region, thereby degrading selectivity. Specifically, transmission electron microscopy analysis demonstrated that near-saturated H2O doses enabled 32.7 nm thick TiO2 patterns at selectivity threshold S > 0.9 on patterned Si/SiO2 substrates. The correlation between selectivity and reactant exposure serves to increase fundamental insights into the effects of sub-saturated self-limiting surface reactions on the quality and effectiveness of ASD processes and methods.
- 12 June 2019
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 31 (13) , 4793-4804
Integrated Isothermal Atomic Layer Deposition/Atomic Layer Etching Supercycles for Area-Selective Deposition of TiO2
- 12 June 2019
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 31 (13) , 4793-4804
Integrated Isothermal Atomic Layer Deposition/Atomic Layer Etching Supercycles for Area-Selective Deposition of TiO2
- 3 February 2016
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 301 (5) , 530-534
Thin Films Bearing Conjugated Polymer Nanoparticles Fabricated by Microliter‐Scale Layer‐by‐Layer Deposition
A conjugated polymer, poly(9,9‐bis(6‐bromohexyl)‐9H‐fluorene‐alt‐1,4‐phenylene), is synthesized, converted to nanoparticles via a nanoprecipitation process, and utilized to fabricate thin films including conjugated polymer nanoparticles. The nanoparticles with surface bromides can be conjugated with an amine‐functionalized dendrimer via a nucleophilic coupling reaction. Thus, when microliter solutions of the particulates are dragged at a constant velocity on substrates alternately in a layer‐by‐layer manner, thin films composed of the nanoparticles and dendrimers can be successfully built up on the substrates. Our results suggest a methodology to control the deposition of thin films bearing conjugated polymer nanoparticles while minimizing processing time and decreasing material consumption. image
- 3 February 2016
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 301 (5) , 530-534
Thin Films Bearing Conjugated Polymer Nanoparticles Fabricated by Microliter‐Scale Layer‐by‐Layer Deposition
A conjugated polymer, poly(9,9‐bis(6‐bromohexyl)‐9H‐fluorene‐alt‐1,4‐phenylene), is synthesized, converted to nanoparticles via a nanoprecipitation process, and utilized to fabricate thin films including conjugated polymer nanoparticles. The nanoparticles with surface bromides can be conjugated with an amine‐functionalized dendrimer via a nucleophilic coupling reaction. Thus, when microliter solutions of the particulates are dragged at a constant velocity on substrates alternately in a layer‐by‐layer manner, thin films composed of the nanoparticles and dendrimers can be successfully built up on the substrates. Our results suggest a methodology to control the deposition of thin films bearing conjugated polymer nanoparticles while minimizing processing time and decreasing material consumption. image