Onome Scott-Emuakpor
Research Subjects
Research Interests
Onome Scott-Emuakpor has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Tommy George
Mem. ASME Air Force Research Laboratory, Aerospace Systems Directorate, Wright-Patterson AFB, OH 45433
13 shared publications - Brian Runyon
Air Force Research Laboratory, Aerospace Systems Directorate , Wright-Patterson AFB, OH 45433
6 shared publications - Dino Celli
The Ohio State University
4 shared publications - Dino Celli
Aerospace Systems Directorate, Air Force Research Laboratory , 1950, 5th Street, WPAFB, OH 45433
3 shared publications - Luke Sheridan
Air Force Research Laboratory
3 shared publications - M. -H. Herman Shen
Professor Fellow ASME Department of Mechanical and Aerospace Engineering, The Ohio State University, 201 W. 19th Avenue, Columbus, OH 43210
3 shared publications
Latest Publications
- 5 December 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (3)
Investigation of Self-Heating During Ultrasonic Fatigue Testing and Effect on Very High Cycle Fatigue Behavior of Titanium 6Al-4V
Very high cycle fatigue (VHCF) data and experiments, 107–109 cycles to failure, have traditionally been both a cumbersome and costly task to perform. However, characterizing VHCF behavior of material systems is critical for the design and sustainability of turbine engines as outlined in the turbine engine structural integrity program (ENSIP). With recent advancements, ultrasonic fatigue (UF) test systems have become increasingly available to generate VHCF fatigue data. A primary consideration for ultrasonic fatigue testing is the frequency of loading, the resulting thermal evolution, and its effect on fatigue life. To mitigate the heat generation within the specimen during experiments, cooling air is directed to the specimen and cyclic loading is performed by selecting an appropriate test frequency or defining a duty cycle rather than continuously subjected to fatigue. However, standardization of experimental test procedures remains ongoing and continues to be developed. In this study, a Shimadzu USF-1000A ultrasonic fatigue test system is used to characterize VHCF behavior of Ti-6Al-4V to understand the effect of duty cycle and thermal evolution on fatigue life for ultrasonic fatigue testing. Titanium 6Al-4V test specimens are subjected to fully reversed axial fatigue at 20 kHz exciting resonance in an axial mode to better characterize the experimental process. Three duty cycle-cooling air configurations and their effect on fatigue life due to self-generated heat during the experiment are investigated. Heat generation is monitored in situ via a single-point optical pyrometer, and in situ mechanical and thermal data are collected and compared to standardized servohydraulic fatigue test data performed in this study as well as from data found in the literature.
- 5 December 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (3)
Investigation of Self-Heating During Ultrasonic Fatigue Testing and Effect on Very High Cycle Fatigue Behavior of Titanium 6Al-4V
Very high cycle fatigue (VHCF) data and experiments, 107–109 cycles to failure, have traditionally been both a cumbersome and costly task to perform. However, characterizing VHCF behavior of material systems is critical for the design and sustainability of turbine engines as outlined in the turbine engine structural integrity program (ENSIP). With recent advancements, ultrasonic fatigue (UF) test systems have become increasingly available to generate VHCF fatigue data. A primary consideration for ultrasonic fatigue testing is the frequency of loading, the resulting thermal evolution, and its effect on fatigue life. To mitigate the heat generation within the specimen during experiments, cooling air is directed to the specimen and cyclic loading is performed by selecting an appropriate test frequency or defining a duty cycle rather than continuously subjected to fatigue. However, standardization of experimental test procedures remains ongoing and continues to be developed. In this study, a Shimadzu USF-1000A ultrasonic fatigue test system is used to characterize VHCF behavior of Ti-6Al-4V to understand the effect of duty cycle and thermal evolution on fatigue life for ultrasonic fatigue testing. Titanium 6Al-4V test specimens are subjected to fully reversed axial fatigue at 20 kHz exciting resonance in an axial mode to better characterize the experimental process. Three duty cycle-cooling air configurations and their effect on fatigue life due to self-generated heat during the experiment are investigated. Heat generation is monitored in situ via a single-point optical pyrometer, and in situ mechanical and thermal data are collected and compared to standardized servohydraulic fatigue test data performed in this study as well as from data found in the literature.
- 5 December 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (3)
Analyses of Damping Sustainability of Additively Manufactured Nickel Alloy Components Subjected to High Strain Loading Cycles
While integrally bladed rotors in turbine engines have multiple benefits, they are more susceptible to vibration and as a result, high cycle fatigue failure. In response, damping treatments such as viscoelastic layers, hard coatings, and particle dampers have been utilized to reduce vibration of integrally bladed rotors and promote long service life. In recent experiments, nickel-based alloy 718 structural beams representative of turbine blades were manufactured via laser powder bed fusion (LPBF) with internal geometries containing unfused powder. Compared to fully fused beams, these beams with internal particle dampers have demonstrated a significant improvement in damping performance, suppressing vibrations by as much as 95%. However, the inherent damping of the particle dampers decreases as the strain amplitude increases when some of the unfused powder fuses to the walls of the pockets. This study investigates the effect of the location of the particle dampers within the beam on the sustainability of its damping performance. To compare the effect of the particle damper's location, the LPBF nickel-based alloy 718 beams are subjected to successive resonance dwells with increasing strain amplitude. After each dwell, the damping performance is assessed via the half-power bandwidth method of the frequency response function. Results from this study indicate that while the location of the particle dampers within the specimen does influence when the damping begins to degrade, it is not the optimal parameter for damping sustainability. The aim of this and future work is to improve the long-term damping performance and viability of the internal particle damper so that it can be more effectively utilized to extend the lifetime of turbomachinery components.
- 5 December 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (3)
Analyses of Damping Sustainability of Additively Manufactured Nickel Alloy Components Subjected to High Strain Loading Cycles
While integrally bladed rotors in turbine engines have multiple benefits, they are more susceptible to vibration and as a result, high cycle fatigue failure. In response, damping treatments such as viscoelastic layers, hard coatings, and particle dampers have been utilized to reduce vibration of integrally bladed rotors and promote long service life. In recent experiments, nickel-based alloy 718 structural beams representative of turbine blades were manufactured via laser powder bed fusion (LPBF) with internal geometries containing unfused powder. Compared to fully fused beams, these beams with internal particle dampers have demonstrated a significant improvement in damping performance, suppressing vibrations by as much as 95%. However, the inherent damping of the particle dampers decreases as the strain amplitude increases when some of the unfused powder fuses to the walls of the pockets. This study investigates the effect of the location of the particle dampers within the beam on the sustainability of its damping performance. To compare the effect of the particle damper's location, the LPBF nickel-based alloy 718 beams are subjected to successive resonance dwells with increasing strain amplitude. After each dwell, the damping performance is assessed via the half-power bandwidth method of the frequency response function. Results from this study indicate that while the location of the particle dampers within the specimen does influence when the damping begins to degrade, it is not the optimal parameter for damping sustainability. The aim of this and future work is to improve the long-term damping performance and viability of the internal particle damper so that it can be more effectively utilized to extend the lifetime of turbomachinery components.
- 5 December 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (3)
Fused Deposition Modeling Fabrication Evaluation of a Ti-6Al-4V Centrifugal Compressor
Centrifugal compressors have a critical impact on the performance of a jet engine and can be made out of aluminum, steel, or titanium alloy. However, if made out of Ti-6Al-4V, it would be more lightweight than if steel were used and stronger than if aluminum were used. Compressors manufactured using traditional techniques can be relatively expensive to manufacture, therefore, fused deposition modeling (FDM) or fused filament fabrication (FFF) can help reduce the cost while maintaining structural integrity. FDM/FFF usually prints polylactic acid (PLA) or acrylonitrile butadiene styrene (ABS) layer-by-layer using an extruder with a spool of material feeding into the extruder. Recently, metal-polymer filaments have become commercially available using this same printing apparatus as common “hobby-class” FDM printers. Using FDM with a metal-polymer matrix allows for a lower cost of production because of the intricate designs it can accomplish with little to no machining involved. Even with the benefits of printing a spool of material using FDM, there has been very little research done of Ti-6Al-4V printed in a FDM format. This document records the feasibility of using Ti-6Al-4V for a centrifugal compressor using FDM by incorporating a three-dimensional structured blue light scanner before heat treatments while also analyzing manufacturing capabilities at the tips of blades as well as the base. This analysis is a first-stage to quantify FDM metal print characteristics and properties.
- 5 December 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (3)
Fused Deposition Modeling Fabrication Evaluation of a Ti-6Al-4V Centrifugal Compressor
Centrifugal compressors have a critical impact on the performance of a jet engine and can be made out of aluminum, steel, or titanium alloy. However, if made out of Ti-6Al-4V, it would be more lightweight than if steel were used and stronger than if aluminum were used. Compressors manufactured using traditional techniques can be relatively expensive to manufacture, therefore, fused deposition modeling (FDM) or fused filament fabrication (FFF) can help reduce the cost while maintaining structural integrity. FDM/FFF usually prints polylactic acid (PLA) or acrylonitrile butadiene styrene (ABS) layer-by-layer using an extruder with a spool of material feeding into the extruder. Recently, metal-polymer filaments have become commercially available using this same printing apparatus as common “hobby-class” FDM printers. Using FDM with a metal-polymer matrix allows for a lower cost of production because of the intricate designs it can accomplish with little to no machining involved. Even with the benefits of printing a spool of material using FDM, there has been very little research done of Ti-6Al-4V printed in a FDM format. This document records the feasibility of using Ti-6Al-4V for a centrifugal compressor using FDM by incorporating a three-dimensional structured blue light scanner before heat treatments while also analyzing manufacturing capabilities at the tips of blades as well as the base. This analysis is a first-stage to quantify FDM metal print characteristics and properties.
- 25 November 2022
- Published by Springer Nature
- p. 63-70
Effects of Internal Particle Damper Thickness and Location on Damping Sustainability of Additively Manufactured Nickel Alloy Beams
- 25 November 2022
- Published by Springer Nature
- p. 63-70
Effects of Internal Particle Damper Thickness and Location on Damping Sustainability of Additively Manufactured Nickel Alloy Beams
- 23 November 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (12)
Refinement of a High Cycle Fatigue Decision-Gate Assessment for Additively Repaired Blades
A recently developed high cycle fatigue (HCF) acceptance criteria demonstrates effectiveness in assessing the viability of two laser directed energy deposition (DED) repair processes on titanium 6Al-4V (Ti 6Al-4V) fan blades. The criteria demonstratively proved effective with basic coupon specimens; however, additional factors need to be considered to include available material or component information and nondestructive evaluation (NDE) conditional acceptance. The results from this study help define a prior rule (entrance statement) that identifies expected results based on manufacturing/microstructure information as well as a second-tier rule incorporating NDE for a more refined HCF acceptance criteria.
- 23 November 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (12)
Refinement of a High Cycle Fatigue Decision-Gate Assessment for Additively Repaired Blades
A recently developed high cycle fatigue (HCF) acceptance criteria demonstrates effectiveness in assessing the viability of two laser directed energy deposition (DED) repair processes on titanium 6Al-4V (Ti 6Al-4V) fan blades. The criteria demonstratively proved effective with basic coupon specimens; however, additional factors need to be considered to include available material or component information and nondestructive evaluation (NDE) conditional acceptance. The results from this study help define a prior rule (entrance statement) that identifies expected results based on manufacturing/microstructure information as well as a second-tier rule incorporating NDE for a more refined HCF acceptance criteria.
- 13 January 2022
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 144 (3) , 1-20
Resonant Ultrasound Spectroscopy: Sensitivity Analysis for Anisotropic Materials With Hexagonal Symmetry
Resonance ultrasound spectroscopy (RUS) is a nondestructive technique for evaluating elastic and an-elastic material properties. The frequencies of free vibrations for a carefully crafted sample are measured, and material properties can be extracted from this. In one popular application, the determination of monocrystal elasticity, the results are not always reliable. In some cases, the resonant frequencies are insensitive to changes in certain elastic constants or their linear combinations. Previous work has been done to characterize these sensitivity issues in materials with isotropic and cubic symmetry. This work examines the sensitivity of elastic constant measurements by the RUS method for materials with hexagonal symmetry, such as titanium-diboride. We investigate the reliability of RUS data and explore supplemental measurements, namely, surface acoustic wave (SAW) to obtain an accurate and complete set of elastic constants.
- 13 January 2022
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 144 (3) , 1-20
Resonant Ultrasound Spectroscopy: Sensitivity Analysis for Anisotropic Materials With Hexagonal Symmetry
Resonance ultrasound spectroscopy (RUS) is a nondestructive technique for evaluating elastic and an-elastic material properties. The frequencies of free vibrations for a carefully crafted sample are measured, and material properties can be extracted from this. In one popular application, the determination of monocrystal elasticity, the results are not always reliable. In some cases, the resonant frequencies are insensitive to changes in certain elastic constants or their linear combinations. Previous work has been done to characterize these sensitivity issues in materials with isotropic and cubic symmetry. This work examines the sensitivity of elastic constant measurements by the RUS method for materials with hexagonal symmetry, such as titanium-diboride. We investigate the reliability of RUS data and explore supplemental measurements, namely, surface acoustic wave (SAW) to obtain an accurate and complete set of elastic constants.
- 3 September 2021
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 143 (10)
Vibration Fatigue Assessment of Additive Manufactured Nickel Alloy With Inherent Damping
The fatigue life behavior and internal surface conditions of inherently damped additive manufactured (AM) specimens subjected to vibration bending are under investigation. This study supports research that demonstrated 95% vibration suppression due to damping capability of AM components with 1–3% internal volume of unfused powder; however, the viability of fatigue performance is unknown. The following effort explores whether internal wall damage caused by unfused powder particle motion debits fatigue life. Comparisons between the fatigue behaviors of unfused powder pocket and fully fused nickel based alloy 718 specimens confirms a long suspected powder interaction phenomena critical to damping performance.
- 3 September 2021
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 143 (10)
Vibration Fatigue Assessment of Additive Manufactured Nickel Alloy With Inherent Damping
The fatigue life behavior and internal surface conditions of inherently damped additive manufactured (AM) specimens subjected to vibration bending are under investigation. This study supports research that demonstrated 95% vibration suppression due to damping capability of AM components with 1–3% internal volume of unfused powder; however, the viability of fatigue performance is unknown. The following effort explores whether internal wall damage caused by unfused powder particle motion debits fatigue life. Comparisons between the fatigue behaviors of unfused powder pocket and fully fused nickel based alloy 718 specimens confirms a long suspected powder interaction phenomena critical to damping performance.
- 9 August 2021
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 143 (12)
Establishing an Acceptance Criteria for Assessing Fatigue of Additive Repair Processes
Criteria for assessing high cycle fatigue (HCF) capability is important for transitioning additive repair technologies to turbine engine applications. By studying the fatigue results of two laser directed energy deposition additive manufacturing repairs on airfoil representative Titanium 6Al-4V coupons, acceptable HCF results for repairs can be determined by observing the confidence in predicted values and the reliability of the empirical data compared to baseline results. The following document details the steps and philosophies behind fabricating coupons that capture the repair capability. Furthermore, regression analysis as well as investigations of dataset distribution, fractography, and microscopy are necessary for instilling confidence in the understanding of repair fatigue behavior. The findings in this work provide a decision gate with quantifiable metrics for advancing novel repair techniques.
- 9 August 2021
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 143 (12)
Establishing an Acceptance Criteria for Assessing Fatigue of Additive Repair Processes
Criteria for assessing high cycle fatigue (HCF) capability is important for transitioning additive repair technologies to turbine engine applications. By studying the fatigue results of two laser directed energy deposition additive manufacturing repairs on airfoil representative Titanium 6Al-4V coupons, acceptable HCF results for repairs can be determined by observing the confidence in predicted values and the reliability of the empirical data compared to baseline results. The following document details the steps and philosophies behind fabricating coupons that capture the repair capability. Furthermore, regression analysis as well as investigations of dataset distribution, fractography, and microscopy are necessary for instilling confidence in the understanding of repair fatigue behavior. The findings in this work provide a decision gate with quantifiable metrics for advancing novel repair techniques.
- Open Access
- 16 July 2021
- Published by ASME International
Modal Validation of Academic Bladed Disk Using Digital Image Correlation
Determining the modal response of integrally bladed rotors (IBRs), or bladed disks (blisks), is critical within the aerospace industry. Specifically for gas turbine engines, experimentally measuring the modal response of a physical IBR is a critical step in determining optimal operating conditions and maintenance schedules. Currently, traveling wave excitation (TWE) is a state of
- 16 July 2021
- Published by ASME International
Open AccessModal Validation of Academic Bladed Disk Using Digital Image Correlation
Determining the modal response of integrally bladed rotors (IBRs), or bladed disks (blisks), is critical within the aerospace industry. Specifically for gas turbine engines, experimentally measuring the modal response of a physical IBR is a critical step in determining optimal operating conditions and maintenance schedules. Currently, traveling wave excitation (TWE) is a state of
- Open Access
- 16 July 2021
- Published by ASME International
Rapid Characterization of Fatigue Performance With Application to Additive Manufactured Components
This paper aims to provide a fatigue life prediction method that can concurrently approximate both SN behavior as well as the inherent variability of fatigue. Variability of fatigue is approximated efficiently with a limited number of experimental tests using a simplified energy based fatigue life prediction method or “Two Point” method. The purpose of such a tool is for the
- 16 July 2021
- Published by ASME International
Open AccessRapid Characterization of Fatigue Performance With Application to Additive Manufactured Components
This paper aims to provide a fatigue life prediction method that can concurrently approximate both SN behavior as well as the inherent variability of fatigue. Variability of fatigue is approximated efficiently with a limited number of experimental tests using a simplified energy based fatigue life prediction method or “Two Point” method. The purpose of such a tool is for the