MAMohammad Abedin

Mohammad Abedin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohammad Abedin has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Structural Health Monitoring of FRP-Reinforced Concrete Bridges Using Vibration Responses

    by Nafiseh Kiani, Mohammad Abedin, Christian C. Steputat, Armin B. Mehrabi, Antonio Nanni


  • Open Access

    Net Section Fracture Assessment of Welded Rectangular Hollow Structural Sections

    by Mohammad Abedin, Nafiseh Kiani, Esmail Shahrokhinasab, Sohrab Mokhtari

    Rectangular Hollow Sections (RHS) because of their high resistance to tension, as well as compression, are commonly used as a bracing member with slotted gusset plate connections in steel structures. Since in this type of connection only part of the section contributes in transferring the tensile load to the gusset plate, shear lag failure may occur in the connection. The AISC specification decreases the effective section net area by a factor to consider the effect of shear lag for a limited connection configuration. This study investigates the effective parameters on the shear lag phenomenon for rectangular hollow section members connected at corners using a single concentric gusset plate. The results of the numerical analysis show that the connection length and connection eccentricity are the only effective parameters in the shear lag, and the effect of gusset plate thickness is negligible because of the symmetric connection. The ultimate tensile capacity of the suggested connection in this study were compared to the typical RHS connection presented in the AISC and the similar double angle sections connected at both legs. The comparison indicates that tensile performance of the suggested connection in this study because of its lower connection eccentricity is much higher than the typical slotted connection and double angle connections. Therefore, a new equation is suggested based on the finite element analyses to modify the AISC equation for these connections.


  • Open Access

    Effect of Cross-Frames on Load Distribution of Steel Bridges with Fractured Girder

    by Mohammad Abedin, Armin B. Mehrabi

    In steel girder bridges, fracture of one girder may occur without noticeable bridge profile changes. It is critical to ensure that the bridge will have adequate capacity to prevent collapse until the next cycle of inspection discovers the damage. It is realized that once one of the bridge girders is fractured, vertical loads need to be distributed through an alternative path to the intact girder(s). In this case, cross-frames can play an important role in transferring the loads and preventing from sudden collapse. This paper investigates the impact of cross-frames on load distribution after a fracture is occurred in one girder. Bridge configurations with different cross-frame spacing were studied using finite element modeling and simulation of the bridge behavior with a fractured steel plate girder. Nonlinear and dynamic solution methods were used for these analyses. Results of this investigation demonstrated the important role cross-frames can play in providing some reserved capacity for the bridge with fractured girder to enhance the bridge redundancy. The contribution of the cross-frames and the behavior of the bridge after fracture in one girder however depends on the configuration of the bridge. A study of the variation of the effect of cross-frames with respect to the number of girders is also included in this paper.


  • Open Access

    Novel Approaches for Fracture Detection in Steel Girder Bridges

    by Mohammad Abedin, Armin B. Mehrabi

    The bottom flanges of steel plate girder bridges can be considered fracture-critical elements depending on the number of girders and bridge configuration. For such cases, it is required that inspection of these bridges be carried out using costly “arms-length” approach. New techniques in structural health monitoring (SHM) that use non-contact sensors and self-powered wireless sensors present alternative approach for inspection. Application of such techniques would allow timely detection and application of repair and strengthening, in other word, providing for more resilient bridges. This paper investigates the feasibility of using a handful of self-powered wireless or non-contact sensors for continuous or periodic monitoring and detection of fracture in steel plate girder bridges. To validate this concept, vibration measurements were performed on an actual bridge in the field, and detailed finite element analyses were carried out on a multi-girder bridge. The records obtained show that vibration amplitude was significantly increased for fractured girder, and a distinct pattern of strain variation was registered in the vicinity of fracture, all of which can be detected effectively with relevant sensors. Moreover, the amplitude and frequency of the vibration was shown to be significant enough for providing the required power for typical sensor(s).


  • Open Access

    Prediction of Plastic Shrinkage Cracking of Self‐Compacting Concrete

    by Parviz Ghoddousi, Armin Abbasi, Esmail Shahrokhinasab, Mohammad Abedin

    Concrete exposed to hot climatic conditions is prone to plastic shrinkage after casting within the first few hours due to the water evaporation and restraining conditions of concrete. This cracking is more commonly observed in concrete elements with a large surface area exposed to drying. In this research, plastic shrinkage of 13 self‐compacting concrete samples with different cement paste volumes and various coarse to total aggregate ratios was studied. Test specimens of fresh concrete were subjected to a wind tunnel, which simulated hot dry environmental condition immediately after casting. It can be observed from the test results that the relationship between free plastic shrinkage and the difference between bleeding and evaporation is direct and linear. Finally, a model for plastic shrinkage estimation was suggested by considering the effect of free plastic shrinkage strain, restraining factor, and tensile strain capacity of self‐compacting concrete.


  • Open Access

    Shear Lag Effects in Angles Welded at Both Legs

    by Mohammad Abedin, Shervin Maleki, Nafiseh Kiani, Esmail Shahrokhinasab

    The shear lag phenomenon is known to reduce the tensile capacity of tension members. There are various parameters affecting shear lag that have not been considered before. In addition, previous studies have been conducted mainly on single steel sections. Using numerical methods, the present study investigates the effects of relevant parameters on shear lag in single‐ and double‐angle sections welded at both legs. The studied parameters are connection eccentricity, connection length, gusset plate thickness, member‐free length, and connection‐free length. The results of the numerical analyses show that, in single‐angle connections, the effects of connection length, connection eccentricity, and gusset plate thickness are more pronounced, while in double‐angle connections the last parameter is not very critical. Comparing the results with the AISC‐LRFD predictions, it is concluded that the specification relations are conservative in most cases. In order to reduce the overconservatism, some new equations for shear lag estimate are introduced.