İlkan Özkan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
İlkan Özkan has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Pınar Duru Baykal
Cukurova Universitesi
6 shared publications Pınar Duru Baykal
Mühendislik Mimarlık Fakültesi Çukurova Üniversitesi Tekstil Mühendisliği Bölümü Adana
3 shared publications- Abdurrahman Telli
Department of Textile Engineering, Cukurova University, Adana, Turkey
2 shared publications - Ferdi Akman
Bingöl University
2 shared publications - Sedat Gündoğdu
Sabancı University
2 shared publications - Yusuf Kuvvetli
Department of Industrial Engineering, Çukurova University, 01330 Adana, Türkiye
2 shared publications
Latest Publications
- Open Access
- 15 October 2026
- Published by Springer Nature in Journal of Coatings Technology and Research
- p. 1-15
Multifunctional UV-curable carbon nanofiber coatings on hemp/viscose nonwovens: electrostatic dissipation, thermal stability, and electromagnetic shielding behavior
Natural fiber-reinforced composites are widely studied as sustainable alternatives to synthetic materials due to their lightweight and renewable nature. In this study, a hemp/viscose spunlace nonwoven was coated with a UV-curable elastomeric resin containing carbon nanofibers (CNF) and acid-activated carbon nanofibers (ACNF) at 0.75, 1.5, and 3 wt%. Acid activation introduced oxygen-containing functional groups, improving nanofiller dispersion and interfacial adhesion. The composites were characterized by FTIR, RAMAN, TGA, XRD, contact angle, surface resistivity, and EMI shielding effectiveness (SE) analyses. Microscopy confirmed successful nanofiller incorporation, particularly in ACNF-modified samples. Surface resistivity results showed a concentration-dependent decrease in resistivity, indicating a shift toward electrostatic dissipative behavior. ACNF samples exhibited lower resistivity than untreated CNF systems. Thermal analysis revealed enhanced thermal stability and higher char residue in reinforced composites. Although measurable attenuation was observed, the SE values (<5 dB) indicate that a fully developed conductive network was not established within the investigated filler range. These findings suggest that the current formulations primarily provide electrostatic dissipation rather than effective electromagnetic shielding. Overall, UV-curable CNF/ACNF coatings improved surface functionality and thermal performance, but low filler contents limited electromagnetic shielding efficiency.
- 15 October 2026
- Published by Springer Nature in Journal of Coatings Technology and Research
- p. 1-15
Open AccessMultifunctional UV-curable carbon nanofiber coatings on hemp/viscose nonwovens: electrostatic dissipation, thermal stability, and electromagnetic shielding behavior
Natural fiber-reinforced composites are widely studied as sustainable alternatives to synthetic materials due to their lightweight and renewable nature. In this study, a hemp/viscose spunlace nonwoven was coated with a UV-curable elastomeric resin containing carbon nanofibers (CNF) and acid-activated carbon nanofibers (ACNF) at 0.75, 1.5, and 3 wt%. Acid activation introduced oxygen-containing functional groups, improving nanofiller dispersion and interfacial adhesion. The composites were characterized by FTIR, RAMAN, TGA, XRD, contact angle, surface resistivity, and EMI shielding effectiveness (SE) analyses. Microscopy confirmed successful nanofiller incorporation, particularly in ACNF-modified samples. Surface resistivity results showed a concentration-dependent decrease in resistivity, indicating a shift toward electrostatic dissipative behavior. ACNF samples exhibited lower resistivity than untreated CNF systems. Thermal analysis revealed enhanced thermal stability and higher char residue in reinforced composites. Although measurable attenuation was observed, the SE values (<5 dB) indicate that a fully developed conductive network was not established within the investigated filler range. These findings suggest that the current formulations primarily provide electrostatic dissipation rather than effective electromagnetic shielding. Overall, UV-curable CNF/ACNF coatings improved surface functionality and thermal performance, but low filler contents limited electromagnetic shielding efficiency.
- Open Access
- 1 August 2026
- Published by IOP Publishing in Environmental Research Communications
- Vol. 8 (8) , 085016
Comparative microfiber shedding from natural, virgin and recycled synthetic textiles under standardised laundering conditions
Microfiber release from synthetic textiles is increasingly recognized as a major source of microplastic pollution, yet the performance of recycled materials relative to virgin and natural remains contested. This study provides standardized evidence on microfiber shedding from commercially available garments, comparing recycled and virgin synthetic fibers alongside natural alternatives. A total of 51 garments from five global fashion brands were analyzed, including cotton, polyester (virgin and recycled), and polyamide (virgin and recycled). To capture complementary shedding metrics, two internationally recognized laundering methods were applied: ISO 105-C06 to quantify fiber number and length, and ISO 6330 to measure total fiber number and mass loss under simulated domestic-scale washing conditions. Descriptively, recycled polyester (rPET) released the highest mean number of microfibers (12430 fibers·g −1 ), approximately 55% more than virgin polyester (8028 fibers·g −1 ); however, this difference was not statistically significant across material categories, reflecting high within-group variability. In contrast, fiber length differed significantly by material type, with rPET and recycled polyamide producing significantly shorter fibers (mean 0.42 mm) than cotton and virgin polyester (mean 0.52 mm). Recycled polyamide showed a similar descriptive trend of higher fiber counts relative to its virgin counterpart. While cotton released a greater total fiber mass (1.85 mg·g −1 ), these fibers were longer and fewer in number. Statistical analysis indicated that microfiber shedding was largely driven by fiber type and material properties rather than brand-specific differences. Nevertheless, some garments -particularly from one brand (B-5)- consistently exhibited higher fiber release across both virgin and recycled synthetic materials, suggesting that textile design and manufacturing practices may also influence shedding intensity. These findings challenge assumptions that rPET is a sustainable alternative and emphasize the need for performance-based evaluation of textile materials in efforts to reduce microfiber emissions.
- 1 August 2026
- Published by IOP Publishing in Environmental Research Communications
- Vol. 8 (8) , 085016
Open AccessComparative microfiber shedding from natural, virgin and recycled synthetic textiles under standardised laundering conditions
Microfiber release from synthetic textiles is increasingly recognized as a major source of microplastic pollution, yet the performance of recycled materials relative to virgin and natural remains contested. This study provides standardized evidence on microfiber shedding from commercially available garments, comparing recycled and virgin synthetic fibers alongside natural alternatives. A total of 51 garments from five global fashion brands were analyzed, including cotton, polyester (virgin and recycled), and polyamide (virgin and recycled). To capture complementary shedding metrics, two internationally recognized laundering methods were applied: ISO 105-C06 to quantify fiber number and length, and ISO 6330 to measure total fiber number and mass loss under simulated domestic-scale washing conditions. Descriptively, recycled polyester (rPET) released the highest mean number of microfibers (12430 fibers·g −1 ), approximately 55% more than virgin polyester (8028 fibers·g −1 ); however, this difference was not statistically significant across material categories, reflecting high within-group variability. In contrast, fiber length differed significantly by material type, with rPET and recycled polyamide producing significantly shorter fibers (mean 0.42 mm) than cotton and virgin polyester (mean 0.52 mm). Recycled polyamide showed a similar descriptive trend of higher fiber counts relative to its virgin counterpart. While cotton released a greater total fiber mass (1.85 mg·g −1 ), these fibers were longer and fewer in number. Statistical analysis indicated that microfiber shedding was largely driven by fiber type and material properties rather than brand-specific differences. Nevertheless, some garments -particularly from one brand (B-5)- consistently exhibited higher fiber release across both virgin and recycled synthetic materials, suggesting that textile design and manufacturing practices may also influence shedding intensity. These findings challenge assumptions that rPET is a sustainable alternative and emphasize the need for performance-based evaluation of textile materials in efforts to reduce microfiber emissions.
- Open Access
- 24 June 2026
- Published by Springer Nature in Radiation and Environmental Biophysics
- Vol. 65 (3) , 1-16
Stereolithography-printed Bi2O3-reinforced photopolymer nanocomposite samples with antibacterial and radiation shielding properties
Stereolithography (SLA) is an additive manufacturing technique that allows the production of polymer composite samples with high accuracy and smooth surface quality. This makes SLA suitable for functional surface applications. In this study, photopolymer nanocomposite surfaces reinforced with bismuth oxide (Bi 2 O 3 ) nanoparticles were produced by SLA and evaluated in terms of surface structure, antibacterial activity, electrical properties, electromagnetic shielding, and ionizing radiation shielding performance. Bi 2 O 3 nanoparticles were added to a commercial UV-curable photopolymer resin at contents of 1, 3, and 5 wt% and printed layer by layer with a layer thickness of 50 μm. Surface structure and particle distribution were examined by SEM–EDS. The results showed good particle distribution at low Bi 2 O 3 contents, while particle accumulation occurred at higher contents due to settling during printing. Antibacterial activity was tested according to ISO 22,196, and all Bi 2 O 3 -reinforced surfaces showed more than 99% reduction against Escherichia coli and Staphylococcus aureus after 24 h. Surface resistivity measurements performed according to TS EN 1149-1 showed values higher than 10 12 Ω, indicating strong electrical insulation. Electromagnetic shielding effectiveness values remained below 5 dB in the 8–12 GHz frequency range. In addition, ionizing radiation shielding parameters, including mass attenuation coefficient, linear attenuation coefficient, half-value layer, and radiation protection efficiency, were theoretically calculated using WinXCOM and EpiXS. The results showed that increasing Bi 2 O 3 content improved photon attenuation, especially at low energies. Overall, Bi2O 3 -reinforced SLA nanocomposites provide strong antibacterial performance, electrical insulation, and improved ionizing radiation shielding, making them suitable for multifunctional surface applications.
- 24 June 2026
- Published by Springer Nature in Radiation and Environmental Biophysics
- Vol. 65 (3) , 1-16
Open AccessStereolithography-printed Bi2O3-reinforced photopolymer nanocomposite samples with antibacterial and radiation shielding properties
Stereolithography (SLA) is an additive manufacturing technique that allows the production of polymer composite samples with high accuracy and smooth surface quality. This makes SLA suitable for functional surface applications. In this study, photopolymer nanocomposite surfaces reinforced with bismuth oxide (Bi 2 O 3 ) nanoparticles were produced by SLA and evaluated in terms of surface structure, antibacterial activity, electrical properties, electromagnetic shielding, and ionizing radiation shielding performance. Bi 2 O 3 nanoparticles were added to a commercial UV-curable photopolymer resin at contents of 1, 3, and 5 wt% and printed layer by layer with a layer thickness of 50 μm. Surface structure and particle distribution were examined by SEM–EDS. The results showed good particle distribution at low Bi 2 O 3 contents, while particle accumulation occurred at higher contents due to settling during printing. Antibacterial activity was tested according to ISO 22,196, and all Bi 2 O 3 -reinforced surfaces showed more than 99% reduction against Escherichia coli and Staphylococcus aureus after 24 h. Surface resistivity measurements performed according to TS EN 1149-1 showed values higher than 10 12 Ω, indicating strong electrical insulation. Electromagnetic shielding effectiveness values remained below 5 dB in the 8–12 GHz frequency range. In addition, ionizing radiation shielding parameters, including mass attenuation coefficient, linear attenuation coefficient, half-value layer, and radiation protection efficiency, were theoretically calculated using WinXCOM and EpiXS. The results showed that increasing Bi 2 O 3 content improved photon attenuation, especially at low energies. Overall, Bi2O 3 -reinforced SLA nanocomposites provide strong antibacterial performance, electrical insulation, and improved ionizing radiation shielding, making them suitable for multifunctional surface applications.
- 1 September 2025
- Published by Elsevier in European Journal of Agronomy
- Vol. 172
A review of non-petroleum alternatives of plastic mulches in agriculture: Knowledge gaps and future recommendations
- 1 September 2025
- Published by Elsevier in European Journal of Agronomy
- Vol. 172
A review of non-petroleum alternatives of plastic mulches in agriculture: Knowledge gaps and future recommendations
- Open Access
- 2 July 2025
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 40 (2) , 251-263
Farklı Bölge Pamuklarından Üretilen Mamul Örme Kumaşların Konfor Özelliklerinin Araştırılması
Pamuk lif özelliklerindeki varyasyonun, iplik ve kumaş kalite ve konfor özellikleri üzerinde önemli bir etkisi olduğu bilinmektedir. Bu çalışmada, aynı türde (Gossypium Hirsutum L.) olan ancak farklı bölgelerde yetişen pamuklarının lif özellikleri, iplik özellikleri ve mamul örme kumaşların bazı termo-fizyolojik konfor özellikleri araştırılmıştır. Bu doğrultuda, altı farklı bölgeden seçilen pamuk tipleriyle Ne 30/1 kompakt penye iplikler üretilmiş ve aynı üretim koşullarında örme ve boyama işlemleri gerçekleştirilmiştir. Test sonuçları grafiklerle karşılaştırmalı olarak değerlendirilmiş ve elde edilen veriler istatistiksel olarak analiz edilmiştir. Çalışma sonucunda, farklı bölgelerde yetiştirilen pamuk lif özelliklerinde gözlemlenen varyasyonların iplik özelliklerine yansıdığı görülmüştür. Bununla birlikte, çalışma kapsamında ele alınan mamul kumaşların konfor özellikleri üzerinde belirgin bir etkisinin olmadığı gözlemlenmiştir.
- 2 July 2025
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 40 (2) , 251-263
Open AccessFarklı Bölge Pamuklarından Üretilen Mamul Örme Kumaşların Konfor Özelliklerinin Araştırılması
Pamuk lif özelliklerindeki varyasyonun, iplik ve kumaş kalite ve konfor özellikleri üzerinde önemli bir etkisi olduğu bilinmektedir. Bu çalışmada, aynı türde (Gossypium Hirsutum L.) olan ancak farklı bölgelerde yetişen pamuklarının lif özellikleri, iplik özellikleri ve mamul örme kumaşların bazı termo-fizyolojik konfor özellikleri araştırılmıştır. Bu doğrultuda, altı farklı bölgeden seçilen pamuk tipleriyle Ne 30/1 kompakt penye iplikler üretilmiş ve aynı üretim koşullarında örme ve boyama işlemleri gerçekleştirilmiştir. Test sonuçları grafiklerle karşılaştırmalı olarak değerlendirilmiş ve elde edilen veriler istatistiksel olarak analiz edilmiştir. Çalışma sonucunda, farklı bölgelerde yetiştirilen pamuk lif özelliklerinde gözlemlenen varyasyonların iplik özelliklerine yansıdığı görülmüştür. Bununla birlikte, çalışma kapsamında ele alınan mamul kumaşların konfor özellikleri üzerinde belirgin bir etkisinin olmadığı gözlemlenmiştir.
- 1 January 2022
- Published by Tekstil Ve Konfeksiyon in TEKSTİL VE KONFEKSİYON
- Vol. 32 (4) , 314-326
Investigation of Performance Properties of Denim Fabrics Containing Cotton/Sustans® Blend Rotor Yarn
It is common to use open-end rotor yarn in the production of denim fabric, which is preferred by people of all ages and social status due to its durability and comfort. Recently, the demand for stretch denim fabrics that can take the body's shape due to the elastic fibers in its structure has been increasing. However, producing elastane-containing yarns in the rotor spinning system is not as practical as ring spinning. For this reason, this study aimed to use the staple Sustans (R) fibers with high elasticity in the rotor spinning system together with cotton fibers and reflect the good elasticity and elongation properties of Sustans (R) fibers to the rotor yarns and denim fabrics. In the study, the staple Sustans (R) fibers based on PTT (Polytrimethylene Terephthalate) were spun with cotton fibers in the rotor spinning system. Then denim fabrics were produced using these yarns in the weft. Later, strength (breaking and tear), dimensional stability (dimensional change after washing, fabric elasticity and growth), abrasion resistance and pilling tests were applied to the produced denim fabrics. Thus, the effects of using Sustans (R) fibers on the strength, dimensional stability, abrasion and pilling properties of denim fabrics were analyzed. As a result of the study, the dimensional change and growth values after washing were developed by using Sustans (R). Although good dimensional stability was observed in the samples, the degree of elasticity was lower than expected. The use of Sustans (R) at rates of 50% and above improved the pilling values of the fabrics. In addition, it has been determined that the use of Sustans (R) in terms of abrasion resistance has a more positive effect at the end of long wear periods.
- 1 January 2022
- Published by Tekstil Ve Konfeksiyon in TEKSTİL VE KONFEKSİYON
- Vol. 32 (4) , 314-326
Investigation of Performance Properties of Denim Fabrics Containing Cotton/Sustans® Blend Rotor Yarn
It is common to use open-end rotor yarn in the production of denim fabric, which is preferred by people of all ages and social status due to its durability and comfort. Recently, the demand for stretch denim fabrics that can take the body's shape due to the elastic fibers in its structure has been increasing. However, producing elastane-containing yarns in the rotor spinning system is not as practical as ring spinning. For this reason, this study aimed to use the staple Sustans (R) fibers with high elasticity in the rotor spinning system together with cotton fibers and reflect the good elasticity and elongation properties of Sustans (R) fibers to the rotor yarns and denim fabrics. In the study, the staple Sustans (R) fibers based on PTT (Polytrimethylene Terephthalate) were spun with cotton fibers in the rotor spinning system. Then denim fabrics were produced using these yarns in the weft. Later, strength (breaking and tear), dimensional stability (dimensional change after washing, fabric elasticity and growth), abrasion resistance and pilling tests were applied to the produced denim fabrics. Thus, the effects of using Sustans (R) fibers on the strength, dimensional stability, abrasion and pilling properties of denim fabrics were analyzed. As a result of the study, the dimensional change and growth values after washing were developed by using Sustans (R). Although good dimensional stability was observed in the samples, the degree of elasticity was lower than expected. The use of Sustans (R) at rates of 50% and above improved the pilling values of the fabrics. In addition, it has been determined that the use of Sustans (R) in terms of abrasion resistance has a more positive effect at the end of long wear periods.
- 1 January 2021
- Published by Elsevier in Applied Radiation and Isotopes
- Vol. 167, 109470
Shielding features, to non-ionizing and ionizing photons, of FeCr-based composites
- 1 January 2021
- Published by Elsevier in Applied Radiation and Isotopes
- Vol. 167, 109470
Shielding features, to non-ionizing and ionizing photons, of FeCr-based composites
- 17 March 2020
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 112 (2) , 264-272
Investigation on the microfiber release under controlled washings from the knitted fabrics produced by recycled and virgin polyester yarns
The ubiquity of plastics in the environment poses a significant risk for both human health and natural ecosystems. Especially the fiber type plastics have a quite high share among these plastics. The textile industry is one of the most important sources of fibers. Recycling is one of the solutions offered to reduce the environmental impact of textile materials. In this study, the release of fibers from the knitted fabrics produced from recycled (R-PET) and virgin polyester (PES) yarns was investigated. Knitted fabrics were washed three times under the same washing conditions according to the TS EN ISO 105-C06 standard by James H. Heal Gyrowash washing machine. It was determined that R-PET knitted fabrics released almost 2.3 times more fibers (4489.93 fiber L−1; 368094.07 fiber kg−1) than the virgin PES fabrics (2034.26 fiber L−1; 167436.58 fiber kg−1). The amount of the released fibers showed a significant reduction with an increase in the number of washing cycles for both R-PET and virgin PES samples. This study showed that the knitted fabrics produced from R-PET released more fiber having the shorter length as compared to virgin PES.
- 17 March 2020
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 112 (2) , 264-272
Investigation on the microfiber release under controlled washings from the knitted fabrics produced by recycled and virgin polyester yarns
The ubiquity of plastics in the environment poses a significant risk for both human health and natural ecosystems. Especially the fiber type plastics have a quite high share among these plastics. The textile industry is one of the most important sources of fibers. Recycling is one of the solutions offered to reduce the environmental impact of textile materials. In this study, the release of fibers from the knitted fabrics produced from recycled (R-PET) and virgin polyester (PES) yarns was investigated. Knitted fabrics were washed three times under the same washing conditions according to the TS EN ISO 105-C06 standard by James H. Heal Gyrowash washing machine. It was determined that R-PET knitted fabrics released almost 2.3 times more fibers (4489.93 fiber L−1; 368094.07 fiber kg−1) than the virgin PES fabrics (2034.26 fiber L−1; 167436.58 fiber kg−1). The amount of the released fibers showed a significant reduction with an increase in the number of washing cycles for both R-PET and virgin PES samples. This study showed that the knitted fabrics produced from R-PET released more fiber having the shorter length as compared to virgin PES.
- 27 February 2020
- Published by The National Research and Development Institute for Textiles and Leather in Industria Textila
- Vol. 71 (01) , 41-49
Investigation of the technical and physical properties of metal composite 1×1 rib knitted fabrics
- 27 February 2020
- Published by The National Research and Development Institute for Textiles and Leather in Industria Textila
- Vol. 71 (01) , 41-49
Investigation of the technical and physical properties of metal composite 1×1 rib knitted fabrics
- Open Access
- 24 January 2020
- Published by Deu Muhendislik Fakultesi Fen ve Muhendislik in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
- Vol. 22 (64) , 1-9
Metal İçerikli Hibrid İplik Üretiminde Eş Karıştırma Yönteminin Kullanımı
Çalışmada poliamid 6.6 iplikler ile bakır, gümüş ve paslanmaz çelik metal monofilamentler, puntalama makinesinde, eş karıştırma yöntemi ile birleştirilmiştir. Üretilen hibrid ipliklerin mikroskop görüntüleri alınmıştır. İpliklerde doğrusal yoğunluk tayini, kopma mukavemeti, kopma uzaması ve tüylülük ölçümleri gerçekleştirilmiştir. Metal filament kullanımının iplik kalite değerlerini olumsuz etkilediği görülmüştür. En iyi iplik özellikleri, çelik içerikli hibrid iplikte ölçülmüştür. Gümüş ve özellikle bakır içerikli hibrid iplik üretimlerinde filament kırılmaları gerçekleşmiştir. Bu filament kırılmalarının, ipliklerin daha sonraki dokuma veya örme gibi işlem adımlarında problem oluşturabilecek düzeyde olduğu görülmüştür. Daha sonraki çalışmalarda puntalama makinesi işlem parametreleri ve metal filament özellikleri üzerinde yapılacak değişiklikler ile iplik özellikleri optimize edilebilecektir. Bu şekilde metal filamentler içeren hibrid ipliklerin üretimine hızlı ve düşük maliyetli alternatif bir yöntem oluşacaktır.
- 24 January 2020
- Published by Deu Muhendislik Fakultesi Fen ve Muhendislik in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
- Vol. 22 (64) , 1-9
Open AccessMetal İçerikli Hibrid İplik Üretiminde Eş Karıştırma Yönteminin Kullanımı
Çalışmada poliamid 6.6 iplikler ile bakır, gümüş ve paslanmaz çelik metal monofilamentler, puntalama makinesinde, eş karıştırma yöntemi ile birleştirilmiştir. Üretilen hibrid ipliklerin mikroskop görüntüleri alınmıştır. İpliklerde doğrusal yoğunluk tayini, kopma mukavemeti, kopma uzaması ve tüylülük ölçümleri gerçekleştirilmiştir. Metal filament kullanımının iplik kalite değerlerini olumsuz etkilediği görülmüştür. En iyi iplik özellikleri, çelik içerikli hibrid iplikte ölçülmüştür. Gümüş ve özellikle bakır içerikli hibrid iplik üretimlerinde filament kırılmaları gerçekleşmiştir. Bu filament kırılmalarının, ipliklerin daha sonraki dokuma veya örme gibi işlem adımlarında problem oluşturabilecek düzeyde olduğu görülmüştür. Daha sonraki çalışmalarda puntalama makinesi işlem parametreleri ve metal filament özellikleri üzerinde yapılacak değişiklikler ile iplik özellikleri optimize edilebilecektir. Bu şekilde metal filamentler içeren hibrid ipliklerin üretimine hızlı ve düşük maliyetli alternatif bir yöntem oluşacaktır.