Benedikt Meinecke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Benedikt Meinecke has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Christian Waldschmidt
Ulm University
8 shared publications - David Werbunat
Ulm University
3 shared publications - Johannes Schlichenmaier
Institute of Microwave Engineering, Ulm University, Ulm, Germany
2 shared publications - Juergen Hasch
Corporate Sector Research and Advance Engineering, Robert Bosch GmbH, Stuttgart, Germany
2 shared publications - Matthias Linder
Institute of Microwave Engineering, Ulm University, Ulm, Germany
2 shared publications - Maximilian Steiner
Institute of Microwave Engineering, Ulm University, Ulm, Germany
2 shared publications
Latest Publications
- Open Access
- 20 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 3 (2) , 625-634
UAV-Based Bistatic SAR-Imaging Using a Stationary Repeater
Synthetic aperture radar (SAR) is an established technique for high-resolution radar imaging relying on the ego-motion of the radar. The long coherent integration time of the radar in conjunction with a linear or circular trajectory enables the illumination of targets under different observation angles leading to robustness against short-time interference signals. The use of a bistatic setup to simultaneously acquire multiple observation angles further increases the aforementioned benefits. In this work, a bistatic SAR system using an active repeater is proposed, in the following called Bistatic Repeater-SAR (BR-SAR). In BR-SAR the repeater acts as a second observer providing a bistatic path with low system cost and hardware effort. This article discusses the BR-SAR approach with all signal processing and hardware considerations necessary to build the bistatic radar system. This includes a description of the full system and signal chain with a focus on the signal separation and evaluation of both monostatic and bistatic signals and the subsequent SAR processing. The approach is verified via simulations and measurements, in which conventional SAR is compared to the proposed BR-SAR system. Hardware effects leading to a deteriorated system performance of the bistatic system are analyzed and countermeasures are discussed and implemented. Finally, the benefits of the bistatic system are demonstrated based on a realistic measurement scenario.
- 20 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 3 (2) , 625-634
Open AccessUAV-Based Bistatic SAR-Imaging Using a Stationary Repeater
Synthetic aperture radar (SAR) is an established technique for high-resolution radar imaging relying on the ego-motion of the radar. The long coherent integration time of the radar in conjunction with a linear or circular trajectory enables the illumination of targets under different observation angles leading to robustness against short-time interference signals. The use of a bistatic setup to simultaneously acquire multiple observation angles further increases the aforementioned benefits. In this work, a bistatic SAR system using an active repeater is proposed, in the following called Bistatic Repeater-SAR (BR-SAR). In BR-SAR the repeater acts as a second observer providing a bistatic path with low system cost and hardware effort. This article discusses the BR-SAR approach with all signal processing and hardware considerations necessary to build the bistatic radar system. This includes a description of the full system and signal chain with a focus on the signal separation and evaluation of both monostatic and bistatic signals and the subsequent SAR processing. The approach is verified via simulations and measurements, in which conventional SAR is compared to the proposed BR-SAR system. Hardware effects leading to a deteriorated system performance of the bistatic system are analyzed and countermeasures are discussed and implemented. Finally, the benefits of the bistatic system are demonstrated based on a realistic measurement scenario.
- Open Access
- 8 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 4, 326-338
Highly Efficient Calibration of Antenna Arrays by Active Targets in the Near-Field
To enhance the capabilities of high-resolution imaging or beamforming, the trend goes towards arrays with high-channel count and large aperture sizes. The operation at increasing mm-wave frequencies exacerbates the consequences of manufacturing tolerances on the array performance, further necessitating the development of high-quality calibrations. Thereby, a large number of array response vectors, addressed in the following as data points, is stored. Typically, one data point is measured at a time for each angle. To reduce the calibration effort, hereby defined as the number of required measurements, a calibration setup employing active calibration targets (ACT) is proposed. This setup allows the storage of a multitude of data points within a single measurement. In addition, this measurement setup is placed in the near-field of the array to relax the requirements on the size of the anechoic chamber. Employing multiple targets makes it challenging to compensate the near-field effects. Therefore, methods are discussed to ensure a consistent quality of the calibration considering the near-field influences from the ACTs. Exemplary measurements deploying an antenna array operating at 78.5demonstrate that this calibration measurement setup employing three ACTs placed in the near-field of the array reduces the calibration effort by a factor of 3 compared to state-of-the-art setups. The average deviation of the antenna phase relations amounts to 4.1 degree, proving that the presented setup achieves the same calibration quality as state-of-the-art setups.
- 8 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 4, 326-338
Open AccessHighly Efficient Calibration of Antenna Arrays by Active Targets in the Near-Field
To enhance the capabilities of high-resolution imaging or beamforming, the trend goes towards arrays with high-channel count and large aperture sizes. The operation at increasing mm-wave frequencies exacerbates the consequences of manufacturing tolerances on the array performance, further necessitating the development of high-quality calibrations. Thereby, a large number of array response vectors, addressed in the following as data points, is stored. Typically, one data point is measured at a time for each angle. To reduce the calibration effort, hereby defined as the number of required measurements, a calibration setup employing active calibration targets (ACT) is proposed. This setup allows the storage of a multitude of data points within a single measurement. In addition, this measurement setup is placed in the near-field of the array to relax the requirements on the size of the anechoic chamber. Employing multiple targets makes it challenging to compensate the near-field effects. Therefore, methods are discussed to ensure a consistent quality of the calibration considering the near-field influences from the ACTs. Exemplary measurements deploying an antenna array operating at 78.5demonstrate that this calibration measurement setup employing three ACTs placed in the near-field of the array reduces the calibration effort by a factor of 3 compared to state-of-the-art setups. The average deviation of the antenna phase relations amounts to 4.1 degree, proving that the presented setup achieves the same calibration quality as state-of-the-art setups.
- 5 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (11) , 5039-5050
Learning on Multistatic Simulation Data for Radar-Based Automotive Gesture Recognition
Radar-based gesture recognition can play a vital role in autonomous vehicles’ interaction with vulnerable road users (VRUs). However, in automotive scenarios the same gesture produces strongly differing radar responses owing to the wide range of variations such as position, orientation, or ego-motion. Since including all kinds of modifications in a measured dataset is laborious, gesture simulations alleviate the measurement effort and increase the robustness against edge and corner cases. Hence, this article presents a flexible geometric human target model allowing the direct introduction of a wide range of modifications, while it facilitates the handling of shadowing effects and multiradar constellations. Using the proposed simulation model, a dataset recorded with a radar sensor network consisting of three chirp sequence (CS) radars is resimulated based on the motion data simultaneously captured with a stereo video system. Completely substituting the measured by the simulated data for training, a convolutional neural network (CNN) classifier still achieves 80.4% cross-validation accuracy on a challenging gesture set, compared with 89.4% for training on the measured data. Moreover, using the simulated data the classifier is shown to successfully generalize to new scenarios not observed in measurements.
- 5 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (11) , 5039-5050
Learning on Multistatic Simulation Data for Radar-Based Automotive Gesture Recognition
Radar-based gesture recognition can play a vital role in autonomous vehicles’ interaction with vulnerable road users (VRUs). However, in automotive scenarios the same gesture produces strongly differing radar responses owing to the wide range of variations such as position, orientation, or ego-motion. Since including all kinds of modifications in a measured dataset is laborious, gesture simulations alleviate the measurement effort and increase the robustness against edge and corner cases. Hence, this article presents a flexible geometric human target model allowing the direct introduction of a wide range of modifications, while it facilitates the handling of shadowing effects and multiradar constellations. Using the proposed simulation model, a dataset recorded with a radar sensor network consisting of three chirp sequence (CS) radars is resimulated based on the motion data simultaneously captured with a stereo video system. Completely substituting the measured by the simulated data for training, a convolutional neural network (CNN) classifier still achieves 80.4% cross-validation accuracy on a challenging gesture set, compared with 89.4% for training on the measured data. Moreover, using the simulated data the classifier is shown to successfully generalize to new scenarios not observed in measurements.
- 6 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (10) , 1251-1254
Near-Field Compensation for Coherent Radar Networks
With radar networks, the resolution of critical radar parameters such as Doppler and angle can be improved compared to a single radar sensor. As the network’s aperture is considerably larger than that of a single radar, a much higher angular resolution is achieved. However, with a large aperture, range-dependent phase deviations, that is, near-field effects, occur and affect the angle estimation. In this work, these near-field effects are evaluated exemplarily for a coherent network. Furthermore, a new strategy to compensate for those network near-field effects is proposed and demonstrated based on measurements. The benefits of the near-field compensation are emphasized by comparing the network’s angle-estimation capabilities with and without compensated near-field effects.
- 6 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (10) , 1251-1254
Near-Field Compensation for Coherent Radar Networks
With radar networks, the resolution of critical radar parameters such as Doppler and angle can be improved compared to a single radar sensor. As the network’s aperture is considerably larger than that of a single radar, a much higher angular resolution is achieved. However, with a large aperture, range-dependent phase deviations, that is, near-field effects, occur and affect the angle estimation. In this work, these near-field effects are evaluated exemplarily for a coherent network. Furthermore, a new strategy to compensate for those network near-field effects is proposed and demonstrated based on measurements. The benefits of the near-field compensation are emphasized by comparing the network’s angle-estimation capabilities with and without compensated near-field effects.
- Open Access
- 3 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 1 (4) , 930-940
Flexible Direction-of-Arrival Simulation for Automotive Radar Target Simulators
In order to simulate realistic traffic scenarios, a radar target simulator must be able to generate multiple radar targets with different directions of arrival. The presented concept is able to generate an arbitrary amount of targets with individual directions of arrival for the radar under test. By measuring the radar channel, the novel approach enables target simulators to simulate arbitrary directions of arrival, while minimizing the required hardware. The optimum setup is derived for radars with a uniform linear receive antenna array. The compensation of placement errors for automotive chirp-sequence frequency modulated continuous wave radars is demonstrated. Finally, the calibration for the setup is provided, and the performance of the presented approach is validated.
- 3 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 1 (4) , 930-940
Open AccessFlexible Direction-of-Arrival Simulation for Automotive Radar Target Simulators
In order to simulate realistic traffic scenarios, a radar target simulator must be able to generate multiple radar targets with different directions of arrival. The presented concept is able to generate an arbitrary amount of targets with individual directions of arrival for the radar under test. By measuring the radar channel, the novel approach enables target simulators to simulate arbitrary directions of arrival, while minimizing the required hardware. The optimum setup is derived for radars with a uniform linear receive antenna array. The compensation of placement errors for automotive chirp-sequence frequency modulated continuous wave radars is demonstrated. Finally, the calibration for the setup is provided, and the performance of the presented approach is validated.
- Open Access
- 14 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (1) , 325-336
OFDM-Based Radar Network Providing Phase Coherent DOA Estimation
Next-generation radar sensors require imaging capabilities with high angular resolution. As for a single sensor, the aperture, and thus the achievable resolution, is limited due to the constraints of the front end, radar networks consisting of multiple sensors are a possible solution. However, their incoherency usually makes joint angle estimation impossible. This article presents a network concept consisting of an orthogonal frequency-division multiplexing (OFDM) radar and repeater elements, which receive the reflections from targets and retransmit them back to the radar. Thereby, any frequency conversion from radio frequency to baseband and vice versa is omitted such that the signal remains coherent to the initial transmit signal. To distinguish the bistatic signal transmitted by the repeater from the monostatic one of the OFDM radar, the orthogonal subcarrier structure of OFDM waveforms is exploited by combining a sparse radar transmit signal with a low-frequency modulation in the repeater. This allows to evaluate the bistatic signals at the radar with standard multiple-input-multiple-output (MIMO)-OFDM signal processing, leading to separate range-Doppler images for each virtual channel. Finally, it is shown that this method offers a coherent angular estimation based on the extended aperture of the network. For this purpose, a method to establish phase coherency by a reconstruction of the modulation phase is presented. The network concept is proved with measurements at 77 GHz.
- 14 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (1) , 325-336
Open AccessOFDM-Based Radar Network Providing Phase Coherent DOA Estimation
Next-generation radar sensors require imaging capabilities with high angular resolution. As for a single sensor, the aperture, and thus the achievable resolution, is limited due to the constraints of the front end, radar networks consisting of multiple sensors are a possible solution. However, their incoherency usually makes joint angle estimation impossible. This article presents a network concept consisting of an orthogonal frequency-division multiplexing (OFDM) radar and repeater elements, which receive the reflections from targets and retransmit them back to the radar. Thereby, any frequency conversion from radio frequency to baseband and vice versa is omitted such that the signal remains coherent to the initial transmit signal. To distinguish the bistatic signal transmitted by the repeater from the monostatic one of the OFDM radar, the orthogonal subcarrier structure of OFDM waveforms is exploited by combining a sparse radar transmit signal with a low-frequency modulation in the repeater. This allows to evaluate the bistatic signals at the radar with standard multiple-input-multiple-output (MIMO)-OFDM signal processing, leading to separate range-Doppler images for each virtual channel. Finally, it is shown that this method offers a coherent angular estimation based on the extended aperture of the network. For this purpose, a method to establish phase coherency by a reconstruction of the modulation phase is presented. The network concept is proved with measurements at 77 GHz.
- Open Access
- 16 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (9) , 3908-3916
Coherent Multistatic MIMO Radar Networks Based on Repeater Tags
In this paper, a coherent multistatic radar network with a novel system architecture is presented, which circumvents the general problems of clock distribution and phase noise-related signal-to-noise ratio (SNR) issues. The proposed network consists of a variable number of multiple-input multiple-output (MIMO) radar sensors and a variable number of repeater tags, all of which operate incoherently on the hardware level. In a minimum configuration, the network only consists of one MIMO radar sensor and a repeater tag. The theory behind such a multistatic network is mathematically derived, and simulations are presented to show key aspects of the network, i.e., multistatic range and Doppler measurements, as well as high-resolution angle estimation, exploiting a very large virtual aperture spanning the whole network. Measurements with one sensor and one repeater tag at 77 GHz are carried out to verify the simulations. The measurements show that the bistatic path between the sensor and the repeater tag retains coherency.
- 16 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (9) , 3908-3916
Open AccessCoherent Multistatic MIMO Radar Networks Based on Repeater Tags
In this paper, a coherent multistatic radar network with a novel system architecture is presented, which circumvents the general problems of clock distribution and phase noise-related signal-to-noise ratio (SNR) issues. The proposed network consists of a variable number of multiple-input multiple-output (MIMO) radar sensors and a variable number of repeater tags, all of which operate incoherently on the hardware level. In a minimum configuration, the network only consists of one MIMO radar sensor and a repeater tag. The theory behind such a multistatic network is mathematically derived, and simulations are presented to show key aspects of the network, i.e., multistatic range and Doppler measurements, as well as high-resolution angle estimation, exploiting a very large virtual aperture spanning the whole network. Measurements with one sensor and one repeater tag at 77 GHz are carried out to verify the simulations. The measurements show that the bistatic path between the sensor and the repeater tag retains coherency.