Andrii Frolov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Andrii Frolov has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Dmytro Leontiev
Kharkiv National Automobile and Highway University
8 shared publications - Evgeny Don
Kharkiv National Automobile and Highway University
4 shared publications Дмитро Леонтьєв
Kharkiv National Automobile and Highway University, 25, Yaroslava Mudrogo str., Kharkiv, 61002
4 shared publications- Oleksandr Kuripka
Харківський національний автомобільно-дорожній університет, 61002, Україна, м. Харків, вул. Ярослава Мудрого, 25
3 shared publications - Valeriy Klimenko
Kharkov National Automobile and Highway University, 25, Yaroslava Mudrogo str., Kharkiv, 61002, Ukraine
3 shared publications - Viktor Bogomolov
Kharkov National Auto and Highway University
2 shared publications
Latest Publications
- Open Access
- 7 July 2025
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 56,p. 29-37
Variability in the interpretation of information in the investigation of road traffic incidents using 3D scanning devices
Problem. One of the key challenges in the investigation of road traffic accidents (RTAs) is the reliable determination of the collision mechanism between vehicles, especially in cases where the vehicles have been moved from the scene. Traditional methods of documentation and analysis often lack sufficient accuracy and objectivity. Goal. The aim of this study is to identify the mechanism of collision between two vehicles by analyzing and comparing their geometric damage patterns obtained via 3D scanning, followed by determining their actual relative positioning at the moment of initial contact. Methodology. To achieve this goal, a portable 3D scanner Artec Leo was used, enabling high-precision scanning of vehicles regardless of their location. The resulting 3D models of the damaged vehicles were aligned with each other and with a digital version of the accident scene diagram. During the analysis, vehicle orientation angles, the location of primary contact, movement directions, and damage characteristics were determined. Results. It was established that the collision occurred at an angle of 8–10° within the driving lane of vehicle 1. This conclusion is supported by the alignment of damage areas, the position of the front right headlamp of vehicle 1, and the distribution of glass and plastic fragments. The zone of initial contact was localized within 2 meters from the right edge of the carriageway. Originality. An integrated approach to digital traffic accident reconstruction using 3D scanning is proposed, allowing for accurate analysis even without access to the original accident scene. Practical value. The methodology can be applied in forensic vehicle examination, court investigations, and insurance case assessments to objectively determine the circumstances of a traffic collision.
- 7 July 2025
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 56,p. 29-37
Open AccessVariability in the interpretation of information in the investigation of road traffic incidents using 3D scanning devices
Problem. One of the key challenges in the investigation of road traffic accidents (RTAs) is the reliable determination of the collision mechanism between vehicles, especially in cases where the vehicles have been moved from the scene. Traditional methods of documentation and analysis often lack sufficient accuracy and objectivity. Goal. The aim of this study is to identify the mechanism of collision between two vehicles by analyzing and comparing their geometric damage patterns obtained via 3D scanning, followed by determining their actual relative positioning at the moment of initial contact. Methodology. To achieve this goal, a portable 3D scanner Artec Leo was used, enabling high-precision scanning of vehicles regardless of their location. The resulting 3D models of the damaged vehicles were aligned with each other and with a digital version of the accident scene diagram. During the analysis, vehicle orientation angles, the location of primary contact, movement directions, and damage characteristics were determined. Results. It was established that the collision occurred at an angle of 8–10° within the driving lane of vehicle 1. This conclusion is supported by the alignment of damage areas, the position of the front right headlamp of vehicle 1, and the distribution of glass and plastic fragments. The zone of initial contact was localized within 2 meters from the right edge of the carriageway. Originality. An integrated approach to digital traffic accident reconstruction using 3D scanning is proposed, allowing for accurate analysis even without access to the original accident scene. Practical value. The methodology can be applied in forensic vehicle examination, court investigations, and insurance case assessments to objectively determine the circumstances of a traffic collision.
- Open Access
- 30 July 2024
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 54,p. 5-14
Regarding the issue of the influence of factors on the braking parameters of M1 category vehicles with electric or hybrid power unit
Problem. The relevance of this work is explained by the fact that there are no works at all in the reference and normative literature on the theory and practice of forensic auto technical examination, and even more so, methodical recommendations regarding the values of the braking parameters of vehicles of the M1 category with an electric power plant. Goal. The purpose of the work is to establish the factors that affect the braking parameters of M1 category vehicles with an electric or hybrid power unit. Methodology. The approaches adopted in the work to solve the set goals are based on the theory of conducting the experiment, the theory of the interaction of the pneumatic tire with the road surface, the theory of the car and the laws of theoretical mechanics. Results. On the basis of the obtained experimental data regarding the value of permanent deceleration and the time value of the increasing deceleration during emergency braking of the M1 category vehicles with an electric or hybrid power unit, the tasks will be solved necessary for conducting forensic engineering and transport examinations for specific road traffic events with the participation of M1 category vehicles with an electric or hybrid power unit. Originality. The results of the study provided an opportunity to get an idea of the influence of factors on the braking parameters of M1 category vehicles with an electric or hybrid power unit. Practical value. The obtained results can be recommended to forensic experts when writing expert opinions or expert studies.
- 30 July 2024
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 54,p. 5-14
Open AccessRegarding the issue of the influence of factors on the braking parameters of M1 category vehicles with electric or hybrid power unit
Problem. The relevance of this work is explained by the fact that there are no works at all in the reference and normative literature on the theory and practice of forensic auto technical examination, and even more so, methodical recommendations regarding the values of the braking parameters of vehicles of the M1 category with an electric power plant. Goal. The purpose of the work is to establish the factors that affect the braking parameters of M1 category vehicles with an electric or hybrid power unit. Methodology. The approaches adopted in the work to solve the set goals are based on the theory of conducting the experiment, the theory of the interaction of the pneumatic tire with the road surface, the theory of the car and the laws of theoretical mechanics. Results. On the basis of the obtained experimental data regarding the value of permanent deceleration and the time value of the increasing deceleration during emergency braking of the M1 category vehicles with an electric or hybrid power unit, the tasks will be solved necessary for conducting forensic engineering and transport examinations for specific road traffic events with the participation of M1 category vehicles with an electric or hybrid power unit. Originality. The results of the study provided an opportunity to get an idea of the influence of factors on the braking parameters of M1 category vehicles with an electric or hybrid power unit. Practical value. The obtained results can be recommended to forensic experts when writing expert opinions or expert studies.
- Open Access
- 30 December 2023
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 53,p. 29-36
Regarding the issue of aquaplaning and the interaction of a car tire with the road surface through a layer of water
Problem. The process of interaction of a pneumatic tire of a car wheel with the surface of the road surface, which is covered with a layer of water, affects the safety of the vehicle movement, therefore, the assessment of the effect of aquaplaning when writing the conclusions of the auto technical examination is an actual direction of research. The study of the effect of aquaplaning will allow forensic experts and specialists in the automotive industry to make an objective analysis and form non-subjective conclusions. Goal. The purpose of the work is to determine the design parameters and operational features of the pneumatic tire, as well as the speed of the vehicle on the process of interaction of the car wheel tire with the surface of the road coating, which is covered with a layer of water. Methodology. The approaches adopted in the work to solve the set goals are based on the theory of aquaplaning, the theory of the interaction of the pneumatic tire with the road surface, the theory of the vehicle and the laws of theoretical mechanics. Results. The obtained results of the research in the form of an analysis make it possible to assess the impact of the aquaplaning effect of a pneumatic tire on road safety. It was established that the thickness of the water layer affects the conditions for meeting the requirements established by the traffic rules, since the decrease in the height of the tire tread pattern leads to unstable contact of the tire with the road surface. Originality. The results of the study provided an opportunity to get an idea of the influence of the design parameters of tires on road safety in terms of forming the conclusions of the motor-technical examination. Practical value. The obtained results can be recommended to forensic experts when writing expert opinions and for expert research
- 30 December 2023
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 53,p. 29-36
Open AccessRegarding the issue of aquaplaning and the interaction of a car tire with the road surface through a layer of water
Problem. The process of interaction of a pneumatic tire of a car wheel with the surface of the road surface, which is covered with a layer of water, affects the safety of the vehicle movement, therefore, the assessment of the effect of aquaplaning when writing the conclusions of the auto technical examination is an actual direction of research. The study of the effect of aquaplaning will allow forensic experts and specialists in the automotive industry to make an objective analysis and form non-subjective conclusions. Goal. The purpose of the work is to determine the design parameters and operational features of the pneumatic tire, as well as the speed of the vehicle on the process of interaction of the car wheel tire with the surface of the road coating, which is covered with a layer of water. Methodology. The approaches adopted in the work to solve the set goals are based on the theory of aquaplaning, the theory of the interaction of the pneumatic tire with the road surface, the theory of the vehicle and the laws of theoretical mechanics. Results. The obtained results of the research in the form of an analysis make it possible to assess the impact of the aquaplaning effect of a pneumatic tire on road safety. It was established that the thickness of the water layer affects the conditions for meeting the requirements established by the traffic rules, since the decrease in the height of the tire tread pattern leads to unstable contact of the tire with the road surface. Originality. The results of the study provided an opportunity to get an idea of the influence of the design parameters of tires on road safety in terms of forming the conclusions of the motor-technical examination. Practical value. The obtained results can be recommended to forensic experts when writing expert opinions and for expert research
- Open Access
- 29 December 2022
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 51,p. 14-25
Determination of the average torsional stiffness of tires of a double vehicle wheel during its interaction with the road surface
Problem. In the scientific and methodological recommendations of forensic institutions and in the scientific and technical literature there are currently no universal methods for determining the braking parameters of cargo multi-axle vehicles that have wheels with double tires, which affects the results of drawing up the conclusions of the motor-technical expertise. The lack of universal methods is due to the difficulty of determining the actual braking, especially when the tires of dual wheels interact with the road surface. Goal. The goal is justification of the method of determining the average torsional stiffness of tires of a double vehicle wheel during its interaction with the road surface. Methodology. The approaches adopted in the work to achieve the set goal are based on the theoretical foundations of the deformation of elastic elements, which are located parallel to each other. Results. Equations are determined that allow you to calculate the value of the average torsional stiffness of the tire for wheels that have double, triple or quadruple tires. Originality. The results of the research provide a general idea of the effect of the pressure in the tires of a double wheel on the value of its average torsional stiffness. Practical value. The obtained results can be recommended to expert motor technicians when drawing up a conclusion of an expertise or an expert study. Besides, the results of the study can be used in the educational process during the training of specialists in the field of transport or mechanical engineering
- 29 December 2022
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 51,p. 14-25
Open AccessDetermination of the average torsional stiffness of tires of a double vehicle wheel during its interaction with the road surface
Problem. In the scientific and methodological recommendations of forensic institutions and in the scientific and technical literature there are currently no universal methods for determining the braking parameters of cargo multi-axle vehicles that have wheels with double tires, which affects the results of drawing up the conclusions of the motor-technical expertise. The lack of universal methods is due to the difficulty of determining the actual braking, especially when the tires of dual wheels interact with the road surface. Goal. The goal is justification of the method of determining the average torsional stiffness of tires of a double vehicle wheel during its interaction with the road surface. Methodology. The approaches adopted in the work to achieve the set goal are based on the theoretical foundations of the deformation of elastic elements, which are located parallel to each other. Results. Equations are determined that allow you to calculate the value of the average torsional stiffness of the tire for wheels that have double, triple or quadruple tires. Originality. The results of the research provide a general idea of the effect of the pressure in the tires of a double wheel on the value of its average torsional stiffness. Practical value. The obtained results can be recommended to expert motor technicians when drawing up a conclusion of an expertise or an expert study. Besides, the results of the study can be used in the educational process during the training of specialists in the field of transport or mechanical engineering
- Open Access
- 24 December 2021
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 49,p. 23-35
Features of braking of multi-axle vehicles depending on the layout of their axles
Анотація Проблема. На даний час в науково-методичних рекомендаціях судово-експертних установ та в науково-технічній літературі відсутні універсальні методики щодо визначення параметрів гальмування вантажних багатовісних транспортних засобів, що не дає можливості використовувати типові підходи при складанні висновків авто-технічної експертизи. Мета. Мета полягає в тому, щоб показати можливість використаннея в практиці проведення автотехнічних експертиз, методики визначення уповільення багатовісного транспортного засобу на основі реалізованих зчеплень шин його коліс та координат положення його центру тяжіння.. Методологія. Прийняті в роботі підходи до вирішення поставленої мети базуються на теоретичних основах гальмування багатовісних транспортних засобів, наукових положень пружних деформацій пневматичних шин автомобільних коліс, геометричних та вагових параметрах колісного транспортного засобу. Результати. Визначено рівняння, які дозволяють розрахувати значення коефіцієнта гальмування багатовісних транспортних засобів на основі координат положення його центру тяжіння, реалізованих зчеплень між шинами автомобільних коліс та поверхнею дорожнього покриття, а також розподілення навантаження між відповідними передніми і задніми вісями багатовісного транспортного засобу. Визначено рівняння, які дозволяють розрахувати положення координати центру тяжіння багатовісного колісного транспортного засобу щодо його передніх і задніх осей. Оригінальність. Результати проведеної роботи дають загальне уявлення про вплив геометричних та вагових параметрів багатовісного транспортного засобу на ефективність його гальмування, в тому числі й при виході з ладу елементів його гальмового керування. Практичне значення. Отримані результати можуть бути рекомендовані експертам-автотехнікам при визначені технічної можливості уникнення дорожньо-транспортної події в умовах виникнення несправностей в гальмовому керуванні транспортного засобу.
- 24 December 2021
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 49,p. 23-35
Open AccessFeatures of braking of multi-axle vehicles depending on the layout of their axles
Анотація Проблема. На даний час в науково-методичних рекомендаціях судово-експертних установ та в науково-технічній літературі відсутні універсальні методики щодо визначення параметрів гальмування вантажних багатовісних транспортних засобів, що не дає можливості використовувати типові підходи при складанні висновків авто-технічної експертизи. Мета. Мета полягає в тому, щоб показати можливість використаннея в практиці проведення автотехнічних експертиз, методики визначення уповільення багатовісного транспортного засобу на основі реалізованих зчеплень шин його коліс та координат положення його центру тяжіння.. Методологія. Прийняті в роботі підходи до вирішення поставленої мети базуються на теоретичних основах гальмування багатовісних транспортних засобів, наукових положень пружних деформацій пневматичних шин автомобільних коліс, геометричних та вагових параметрах колісного транспортного засобу. Результати. Визначено рівняння, які дозволяють розрахувати значення коефіцієнта гальмування багатовісних транспортних засобів на основі координат положення його центру тяжіння, реалізованих зчеплень між шинами автомобільних коліс та поверхнею дорожнього покриття, а також розподілення навантаження між відповідними передніми і задніми вісями багатовісного транспортного засобу. Визначено рівняння, які дозволяють розрахувати положення координати центру тяжіння багатовісного колісного транспортного засобу щодо його передніх і задніх осей. Оригінальність. Результати проведеної роботи дають загальне уявлення про вплив геометричних та вагових параметрів багатовісного транспортного засобу на ефективність його гальмування, в тому числі й при виході з ладу елементів його гальмового керування. Практичне значення. Отримані результати можуть бути рекомендовані експертам-автотехнікам при визначені технічної можливості уникнення дорожньо-транспортної події в умовах виникнення несправностей в гальмовому керуванні транспортного засобу.
- Open Access
- 29 May 2021
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 48,p. 27-37
FEATURES OF ADAPTIVE BRAKE CONTROL OF THE SECONDARY BRAKE SYSTEM OF A MULTI-AXLE VEHICLE
Problem. A malfunction of the service braking system of a wheeled vehicle (CTS) significantly affects road safety, especially when operating multi-axle vehicles with large masses. One of the ways to increase the level of road safety of multi-axle vehicles, when braking them using a spare (emergency) braking system, is the introduction of automated adaptive braking systems into the design of the brake drive of vehicles. The definition of the limits of the use of the adaptive braking system on vehicles with many axles is almost not disclosed in the scientific and technical literature, therefore, the issue of using such a system on vehicles with a large number of axles requires additional research. Purpose. The purpose of this work is to develop a simulation model for adaptive control of the braking process of a multi-axle vehicle using a spare (emergency) braking system, taking into account the simulation of the dynamics of the drive and the variability of the adhesion properties between the tire of the vehicle wheel and the road surface. Methodology. To achieve this goal, it is necessary to develop a simulation model of the brake drive in an adaptive mode, implement a model of the interaction of the tire with the road surface, and implement a model of the braking dynamics of a multi-axle vehicle in the event of a malfunction of its service brake system. Originality. The proposed key criterion (Kr) for changing the throttle section in electro-pneumatic pressure modulators, which provide adaptive air inlet or outlet from the corresponding brake chambers of the drive, during simulation, made it possible to simulate the operation of the drive circuits in the adaptive mode. It has been established that, depending on the potential for the realization of the adhesion between the tires of automobile wheels and the road surface, the pressure in the electro-pneumatic brake drive with its adaptive regulation can be increased by no more than 0.04 MPa.
- 29 May 2021
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 48,p. 27-37
Open AccessFEATURES OF ADAPTIVE BRAKE CONTROL OF THE SECONDARY BRAKE SYSTEM OF A MULTI-AXLE VEHICLE
Problem. A malfunction of the service braking system of a wheeled vehicle (CTS) significantly affects road safety, especially when operating multi-axle vehicles with large masses. One of the ways to increase the level of road safety of multi-axle vehicles, when braking them using a spare (emergency) braking system, is the introduction of automated adaptive braking systems into the design of the brake drive of vehicles. The definition of the limits of the use of the adaptive braking system on vehicles with many axles is almost not disclosed in the scientific and technical literature, therefore, the issue of using such a system on vehicles with a large number of axles requires additional research. Purpose. The purpose of this work is to develop a simulation model for adaptive control of the braking process of a multi-axle vehicle using a spare (emergency) braking system, taking into account the simulation of the dynamics of the drive and the variability of the adhesion properties between the tire of the vehicle wheel and the road surface. Methodology. To achieve this goal, it is necessary to develop a simulation model of the brake drive in an adaptive mode, implement a model of the interaction of the tire with the road surface, and implement a model of the braking dynamics of a multi-axle vehicle in the event of a malfunction of its service brake system. Originality. The proposed key criterion (Kr) for changing the throttle section in electro-pneumatic pressure modulators, which provide adaptive air inlet or outlet from the corresponding brake chambers of the drive, during simulation, made it possible to simulate the operation of the drive circuits in the adaptive mode. It has been established that, depending on the potential for the realization of the adhesion between the tires of automobile wheels and the road surface, the pressure in the electro-pneumatic brake drive with its adaptive regulation can be increased by no more than 0.04 MPa.
- Open Access
- 1 May 2021
- Published by Kharkiv National Automobile and Highway University in Vehicle and Electronics. Innovative Technologies
- No. 19,p. 28-34
Determination of tangential properties of a single pneumatic tire in the vehicle braking mode of a vehicle
Problem. In the event of circumstances that may cause a traffic accident (accident), drivers apply emergency braking, which usually leads to the blocking of car wheels and the formation on the road surface of track information from pneumatic tires. If automated brake force control systems are installed in the brake actuator of the vehicle, the tracking information from the pneumatic tires may be absent or weak, and the braking efficiency of the wheeled vehicle will depend on the angular deformation of the tire relative to the road surface, which in turn is limited. coupling properties in the contact spot "tire-road surface". Goal. The aim of the work is to improve the method of determining the angle of twist of the pneumatic tire of a single car wheel in the mode of its braking by taking into account the effects of the coefficient of friction-sliding on roads with high traction. Methodology the peculiarities of twisting the pneumatic tire of a car wheel with a single busbar in the mode of vehicle braking on roads with low and high coefficient of friction - sliding are considered. The analysis of the model of dynamic change of the tire twist angle depending on the sliding of the tire tread elements in the spot of contact with the road surface is performed, and the results of simulation modeling are obtained, which are confirmed by experimental experiments. Originality. An empirical dependence is proposed, which takes into account the nature of the decrease in the value of the angle of twist of the tire on roads with high traction properties. Practical value. The obtained results of simulation modeling according to the proposed dependence determine that the highest indicators of torsional rigidity of the pneumatic tire are reached at a tire pressure of 0.8 MPa and a vertical load on it of about 2.6 104 N.
- 1 May 2021
- Published by Kharkiv National Automobile and Highway University in Vehicle and Electronics. Innovative Technologies
- No. 19,p. 28-34
Open AccessDetermination of tangential properties of a single pneumatic tire in the vehicle braking mode of a vehicle
Problem. In the event of circumstances that may cause a traffic accident (accident), drivers apply emergency braking, which usually leads to the blocking of car wheels and the formation on the road surface of track information from pneumatic tires. If automated brake force control systems are installed in the brake actuator of the vehicle, the tracking information from the pneumatic tires may be absent or weak, and the braking efficiency of the wheeled vehicle will depend on the angular deformation of the tire relative to the road surface, which in turn is limited. coupling properties in the contact spot "tire-road surface". Goal. The aim of the work is to improve the method of determining the angle of twist of the pneumatic tire of a single car wheel in the mode of its braking by taking into account the effects of the coefficient of friction-sliding on roads with high traction. Methodology the peculiarities of twisting the pneumatic tire of a car wheel with a single busbar in the mode of vehicle braking on roads with low and high coefficient of friction - sliding are considered. The analysis of the model of dynamic change of the tire twist angle depending on the sliding of the tire tread elements in the spot of contact with the road surface is performed, and the results of simulation modeling are obtained, which are confirmed by experimental experiments. Originality. An empirical dependence is proposed, which takes into account the nature of the decrease in the value of the angle of twist of the tire on roads with high traction properties. Practical value. The obtained results of simulation modeling according to the proposed dependence determine that the highest indicators of torsional rigidity of the pneumatic tire are reached at a tire pressure of 0.8 MPa and a vertical load on it of about 2.6 104 N.
- Open Access
- 26 June 2020
- Published by National Scientific Center "Hon. Prof. M. S. Bokarius Forensic Science Institute" of the Ministry of Justice of Ukraine in Theory and Practice of Forensic Science and Criminalistics
- Vol. 21 (1) , 441-451
EXAMINATION OF TRUCK TIRES AS TO IDENTIFICATION OF DAMAGES WHICH ARE FORMED AS A RESULT OF OPERATIONAL TIRE WEAR OR PRODUCT DEFECT
The sequence of carrying out of researches of tires of a freight vehicle on the basis of expert practice is considered. The research of tires of a truck has been conducted, an example of an expert research of tires is resulted, as a result of which the causes of damage of tires were established. The tire connects the vehicle to the road, perceives its weight, braking effort and dynamic impact that arises due to the roughness of the road surface. It is not uncommon for the vehicle to operate even on roads with a satisfactory road surface and damage to the tires. Damage to the tires can be generated as a result of industrial damage (factory defect) and as a result of operational damage. The most common and serious cause of premature wear and damage to tires is non-compliance with the established air pressure norms and overload tires. Changing the configuration of the profile and increasing the deformation of the bus cause an increase in the voltage in its material. As a result, it increases its premature wear. At increased load (overload) the tension voltage in the places of contact of the tire with the road increases and its specific pressure on the road, from which the tread wears away more quickly. Overvoltage in the material and increase in deformation is accompanied by a general increase in friction and heat formation in the tire. At increased load (overload) the tension voltage in the places of contact of the tire with the road increases and its specific pressure on the road, from which the tread wears away more quickly. Overvoltage in the material and increase in deformation is accompanied by a general increase in friction and heat formation in the tire. In the course of the research it was established that the tires Satoya SD 062-III have operational damage, the detects damage to the tires was formed as a result of their operation, which could contribute to vehicle overload, non compliance with tire pressure and the movement of the vehicle on roads with improper road surface. External inspection the examination of Satoya SD 062-III tires showed no signs of industrial damage (factory defects).
- 26 June 2020
- Published by National Scientific Center "Hon. Prof. M. S. Bokarius Forensic Science Institute" of the Ministry of Justice of Ukraine in Theory and Practice of Forensic Science and Criminalistics
- Vol. 21 (1) , 441-451
Open AccessEXAMINATION OF TRUCK TIRES AS TO IDENTIFICATION OF DAMAGES WHICH ARE FORMED AS A RESULT OF OPERATIONAL TIRE WEAR OR PRODUCT DEFECT
The sequence of carrying out of researches of tires of a freight vehicle on the basis of expert practice is considered. The research of tires of a truck has been conducted, an example of an expert research of tires is resulted, as a result of which the causes of damage of tires were established. The tire connects the vehicle to the road, perceives its weight, braking effort and dynamic impact that arises due to the roughness of the road surface. It is not uncommon for the vehicle to operate even on roads with a satisfactory road surface and damage to the tires. Damage to the tires can be generated as a result of industrial damage (factory defect) and as a result of operational damage. The most common and serious cause of premature wear and damage to tires is non-compliance with the established air pressure norms and overload tires. Changing the configuration of the profile and increasing the deformation of the bus cause an increase in the voltage in its material. As a result, it increases its premature wear. At increased load (overload) the tension voltage in the places of contact of the tire with the road increases and its specific pressure on the road, from which the tread wears away more quickly. Overvoltage in the material and increase in deformation is accompanied by a general increase in friction and heat formation in the tire. At increased load (overload) the tension voltage in the places of contact of the tire with the road increases and its specific pressure on the road, from which the tread wears away more quickly. Overvoltage in the material and increase in deformation is accompanied by a general increase in friction and heat formation in the tire. In the course of the research it was established that the tires Satoya SD 062-III have operational damage, the detects damage to the tires was formed as a result of their operation, which could contribute to vehicle overload, non compliance with tire pressure and the movement of the vehicle on roads with improper road surface. External inspection the examination of Satoya SD 062-III tires showed no signs of industrial damage (factory defects).
- 18 July 2019
- Published by Springer Nature
- p. 50-61
Simulation of Working Process of the Electronic Brake System of the Heavy Vehicle
- 18 July 2019
- Published by Springer Nature
- p. 50-61
Simulation of Working Process of the Electronic Brake System of the Heavy Vehicle