Tao Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tao Jiang has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Guangming Xu
8 shared publicationsYong Li
8 shared publicationsYonghui Sun
5 shared publicationsZhaodong Wang
5 shared publicationsBoyue Xu
4 shared publicationsHongyang Zhao
4 shared publications
Latest Publications
- Open Access
- 22 March 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 1194-1201
Optimization of microstructure and properties of high-silicon aluminum alloys for electronic packaging based on semi-solid thixotropic forming process
- 22 March 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 1194-1201
Open AccessOptimization of microstructure and properties of high-silicon aluminum alloys for electronic packaging based on semi-solid thixotropic forming process
- 1 January 2023
- Published by Curran Associates, Inc.
- p. 1174-1179
High-value Utilization of Vanadium-chromium Slag: in Situ Preparation of VS4@rGO Composites from Leaching Solution
- 1 January 2023
- Published by Curran Associates, Inc.
- p. 1174-1179
High-value Utilization of Vanadium-chromium Slag: in Situ Preparation of VS4@rGO Composites from Leaching Solution
- Open Access
- 1 January 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (1) , 016516
Improving element uniformity and mechanical properties of Al–Mg–Si alloy fabricated by twin roll casting with superheat melt treatment
The effect of superheat melt treatment(SMT) on microstructure and properties of Al–Mg–Si alloy fabricated by twin roll casting(TRC) was analyzed using optical microscope, scanning electron microscopy, emission electron probe micro analyzer and transmission electron microscopy. SMT increased the subcooling degree of melt during TRC. The solidification microstructure with high dendrite density and small dendrite spacing was obtained. The second phase was evenly distributed between dendrites and the solute concentration gradient was decreased. Intergranular solute aggregation caused by Reynolds’ dilatancy in TRC slab was effectively suppressed. The homogeneous solute distribution of TRC slab with SMT can be realized by short-time homogenization heat treatment. The size of insoluble particles was greatly reduced. The complete decomposition of non-equilibrium eutectic phase increased the solute concentration in α-Al, which promoted the precipitation of precipitates during aging heat treatment. The tensile strength and yield strength of T6 slab were improved, while the uniform elongation are almost not decreased. The strength and uniform of slab in T4P state were both improved. The obtained results can help further shorten the production cycle of TRC slabs and improve mechanical properties.
- 1 January 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (1) , 016516
Open AccessImproving element uniformity and mechanical properties of Al–Mg–Si alloy fabricated by twin roll casting with superheat melt treatment
The effect of superheat melt treatment(SMT) on microstructure and properties of Al–Mg–Si alloy fabricated by twin roll casting(TRC) was analyzed using optical microscope, scanning electron microscopy, emission electron probe micro analyzer and transmission electron microscopy. SMT increased the subcooling degree of melt during TRC. The solidification microstructure with high dendrite density and small dendrite spacing was obtained. The second phase was evenly distributed between dendrites and the solute concentration gradient was decreased. Intergranular solute aggregation caused by Reynolds’ dilatancy in TRC slab was effectively suppressed. The homogeneous solute distribution of TRC slab with SMT can be realized by short-time homogenization heat treatment. The size of insoluble particles was greatly reduced. The complete decomposition of non-equilibrium eutectic phase increased the solute concentration in α-Al, which promoted the precipitation of precipitates during aging heat treatment. The tensile strength and yield strength of T6 slab were improved, while the uniform elongation are almost not decreased. The strength and uniform of slab in T4P state were both improved. The obtained results can help further shorten the production cycle of TRC slabs and improve mechanical properties.
- Open Access
- 1 November 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 15, 6295-6311
A novel research on the solute redistribution phenomenon of sub-rapid twin-roll cast Al-50 wt.% alloy treated by semi-solid heat treatment
- 1 November 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 15, 6295-6311
Open AccessA novel research on the solute redistribution phenomenon of sub-rapid twin-roll cast Al-50 wt.% alloy treated by semi-solid heat treatment
- 22 June 2021
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1035, 39-45
Penetration Damaging Behavior of ATI425 Titanium Alloy
The penetration damaging behavior of ATI425 titanium alloy was studied by 7.62 mm diameter armor piercing projectiles. The damage characteristics and the mechanism were analyzed by observing and analyzing the craters of ATI425 titanium alloy target. It can be found that local temperature-rise of the target plate occurred, even sputtering phenomenon in the opening stage. The shear bands extended upward along the cater wall could be seen in the stable stage. The large non-homogeneous deformation in adiabatic shear bands caused microcracks and micropores. A large number of macro-cracks were observed on the side wall and at the bottom of the crater.
- 22 June 2021
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1035, 39-45
Penetration Damaging Behavior of ATI425 Titanium Alloy
The penetration damaging behavior of ATI425 titanium alloy was studied by 7.62 mm diameter armor piercing projectiles. The damage characteristics and the mechanism were analyzed by observing and analyzing the craters of ATI425 titanium alloy target. It can be found that local temperature-rise of the target plate occurred, even sputtering phenomenon in the opening stage. The shear bands extended upward along the cater wall could be seen in the stable stage. The large non-homogeneous deformation in adiabatic shear bands caused microcracks and micropores. A large number of macro-cracks were observed on the side wall and at the bottom of the crater.
- Open Access
- 1 June 2021
- Published by Elsevier in Progress in Natural Science: Materials International
- Vol. 31 (3) , 461-470
A novel investigation on the influence of Cu–P modifier on the microstructure, mechanical performance, and melting process of Al–50Si alloys treated by overheating
- 1 June 2021
- Published by Elsevier in Progress in Natural Science: Materials International
- Vol. 31 (3) , 461-470
Open AccessA novel investigation on the influence of Cu–P modifier on the microstructure, mechanical performance, and melting process of Al–50Si alloys treated by overheating
- 1 September 2020
- Published by Elsevier in Materials Letters
- Vol. 274
Effect of electric current pulses on TiB2 particle dispersion in aluminum alloy melt
- 1 September 2020
- Published by Elsevier in Materials Letters
- Vol. 274
Effect of electric current pulses on TiB2 particle dispersion in aluminum alloy melt