Ji-Hyun Jeong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ji-Hyun Jeong has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Hwan-Cheol Park4 shared publications
- Dong Won Jung
Faculty of Applied Energy System, Major of Mechanical Engineering, Jeju National University, Jeju-Si, Republic of Korea
2 shared publications - Osama Ali
Jeju National University
2 shared publications - Ai Ting
Department of Mechanical Engineering, Jeju National University, Jeju 63243, Republic of Korea
1 shared publication - Anisha Karki
Department of Mechanical Engineering, Jeju National University, Jeju 63243, Republic of Korea
1 shared publication - Atif Niaz
Jeju National University
1 shared publication
Latest Publications
- Open Access
Thermo-Structural and Dynamic Performance Analysis of a 42CrMo4 Steel Ball Screw Assembly
This study presents a comprehensive thermo-structural and modal analysis of a ball screw assembly. Thermal analysis revealed a maximum temperature of 29.1 °C at the ball nut, corresponding to a total rise of 7.1 °C above ambient. The resulting thermal deformation reached 77.81 μm, while the von Mises stress peaked at 53.9 MPa, both within acceptable limits. Modal simulation of 360 modes showed a sharp increase in frequency with mode number and larger deformation patterns at the higher modes. The first two modes dominate the effective mass with the first 8 modes capturing over 90% of the cumulative effective mass. Overall, the results demonstrate stable thermal performance, limited deformation, low stress, and controlled vibrations, confirming the modeling approach and the suitability of 42CrMo4 steel for high-precision ball screw assemblies.
Open AccessThermo-Structural and Dynamic Performance Analysis of a 42CrMo4 Steel Ball Screw Assembly
This study presents a comprehensive thermo-structural and modal analysis of a ball screw assembly. Thermal analysis revealed a maximum temperature of 29.1 °C at the ball nut, corresponding to a total rise of 7.1 °C above ambient. The resulting thermal deformation reached 77.81 μm, while the von Mises stress peaked at 53.9 MPa, both within acceptable limits. Modal simulation of 360 modes showed a sharp increase in frequency with mode number and larger deformation patterns at the higher modes. The first two modes dominate the effective mass with the first 8 modes capturing over 90% of the cumulative effective mass. Overall, the results demonstrate stable thermal performance, limited deformation, low stress, and controlled vibrations, confirming the modeling approach and the suitability of 42CrMo4 steel for high-precision ball screw assemblies.
- Open Access
Comparative Analysis of the Reliability and Durability of TIC and NSK Ball Screws for Enhanced Process Optimization
Ball screws play an important role in machine tools by converting rotational motion into precise linear motion. This study evaluates and compares ball screws from two companies (TIC and NSK) through simulations and experimentation to assist in the selection process. Simulation results show that TIC exhibits a lower maximum temperature (32.6 °C) and axial deformation (119.3 μm) compared to NSK (34.05 °C and 174 μm, respectively), indicating superior thermal performance and deformation properties. An accelerated life test conducted over 240 h further demonstrates that TIC maintained more stable temperatures during continuous operation. Additional tests on the TIC ball screw include thermal displacement which is 13.5 μm after 2000 cycles of reciprocating motion. Friction torque fluctuation rate which ranges from 11.6% to 19.9%, and test bench positioning repeatability experiment shows a mean deviation of 4.99 μm from the target position. Overall, the results from this work contribute to process optimization by guiding the selection of ball screws based on their thermal performance and durability, ultimately enhancing machine tool accuracy and reliability.
Open AccessComparative Analysis of the Reliability and Durability of TIC and NSK Ball Screws for Enhanced Process Optimization
Ball screws play an important role in machine tools by converting rotational motion into precise linear motion. This study evaluates and compares ball screws from two companies (TIC and NSK) through simulations and experimentation to assist in the selection process. Simulation results show that TIC exhibits a lower maximum temperature (32.6 °C) and axial deformation (119.3 μm) compared to NSK (34.05 °C and 174 μm, respectively), indicating superior thermal performance and deformation properties. An accelerated life test conducted over 240 h further demonstrates that TIC maintained more stable temperatures during continuous operation. Additional tests on the TIC ball screw include thermal displacement which is 13.5 μm after 2000 cycles of reciprocating motion. Friction torque fluctuation rate which ranges from 11.6% to 19.9%, and test bench positioning repeatability experiment shows a mean deviation of 4.99 μm from the target position. Overall, the results from this work contribute to process optimization by guiding the selection of ball screws based on their thermal performance and durability, ultimately enhancing machine tool accuracy and reliability.
- 30 April 2023
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 27 (2) , 27-32
A Study on the Appropriateness of Design of Compressed Copper Tube Fitting Machine
압력 유체의 이송에 사용되는 배관은 높은 수준의 내식성, 열전도성 및 기계적 특성이 필요하다. 이러한 조건을 만족하는 대표적인 배관은 동관으로 일반 산업계에서 널리 사용되고 있다. 본 연구에서는 공조 냉동기의 냉매 배관으로 사용되는 동관 접합 방식의 인화성 문제를 개선하고자 한다. 기존 동관 산소용접을 대체할 무용접 이중 압착식 이음 방법을 대안으로 제안한다. 제안된 방식은 3D 모델링으로 구현하고, 시뮬레이션은 벤딩 전용 해석 프로그램인 Deform 3D를 사용한다.
- 30 April 2023
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 27 (2) , 27-32
A Study on the Appropriateness of Design of Compressed Copper Tube Fitting Machine
압력 유체의 이송에 사용되는 배관은 높은 수준의 내식성, 열전도성 및 기계적 특성이 필요하다. 이러한 조건을 만족하는 대표적인 배관은 동관으로 일반 산업계에서 널리 사용되고 있다. 본 연구에서는 공조 냉동기의 냉매 배관으로 사용되는 동관 접합 방식의 인화성 문제를 개선하고자 한다. 기존 동관 산소용접을 대체할 무용접 이중 압착식 이음 방법을 대안으로 제안한다. 제안된 방식은 3D 모델링으로 구현하고, 시뮬레이션은 벤딩 전용 해석 프로그램인 Deform 3D를 사용한다.
- 30 April 2022
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 26 (2) , 58-63
A Basic Study on Structural Design of Two-Stage Compression Fitting Device for Copper Pipe
In general, copper tubes with high corrosion resistance, high thermal conductivity and high mechanical properties for the transfer of pressurized fluids are used in industry. In the field of using a refrigerant having a flammability problem, the joint method of the copper pipe by oxygen welding still remains a problem to be solved. This study proposes a compression fitting method that can solve the flammability problem by breaking away from the conventional oxygen welding method of the copper pipe used for refrigerant transfer in the air conditioner. The compression fitting device is implemented as 3D modeling and the joint characteristics of the copper pipe are verified through simulation. This study analyzes the contact length of internal and external copper pipes according to the shape of a roller that generates pressing force when pressing the copper pipe.
- 30 April 2022
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 26 (2) , 58-63
A Basic Study on Structural Design of Two-Stage Compression Fitting Device for Copper Pipe
In general, copper tubes with high corrosion resistance, high thermal conductivity and high mechanical properties for the transfer of pressurized fluids are used in industry. In the field of using a refrigerant having a flammability problem, the joint method of the copper pipe by oxygen welding still remains a problem to be solved. This study proposes a compression fitting method that can solve the flammability problem by breaking away from the conventional oxygen welding method of the copper pipe used for refrigerant transfer in the air conditioner. The compression fitting device is implemented as 3D modeling and the joint characteristics of the copper pipe are verified through simulation. This study analyzes the contact length of internal and external copper pipes according to the shape of a roller that generates pressing force when pressing the copper pipe.
- 30 June 2021
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 25 (3) , 62-71
A Study on Active Vibration Isolation System Design for High Precision Fabrication Table Based on Noninteracting Control Theory
This paper presents a novel method for designing a active vibration isolation system (AVIS) by noninteracting control theory. In the result, the designed system can effectively reject the impact of disturbances on high precision fabrication table. In particular, the authors provide a noninteracting control scheme to decrease and delete the interactions appeared in the controlled system dynamics such that the control performance can be improved. For designing an optimal servo system, the LMI (linear matrix inequality) approach is introduced. To verify the effectiveness of the proposed method, a simulation is performed. In the result, the vibration suppression performance is significantly improved, thereby enabling higher precision works.
- 30 June 2021
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 25 (3) , 62-71
A Study on Active Vibration Isolation System Design for High Precision Fabrication Table Based on Noninteracting Control Theory
This paper presents a novel method for designing a active vibration isolation system (AVIS) by noninteracting control theory. In the result, the designed system can effectively reject the impact of disturbances on high precision fabrication table. In particular, the authors provide a noninteracting control scheme to decrease and delete the interactions appeared in the controlled system dynamics such that the control performance can be improved. For designing an optimal servo system, the LMI (linear matrix inequality) approach is introduced. To verify the effectiveness of the proposed method, a simulation is performed. In the result, the vibration suppression performance is significantly improved, thereby enabling higher precision works.
- 31 August 2020
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 24 (4) , 83-88
A Study on Characteristics of Bending Deformation for the Copper Pipe by Double Ball Mandrel
In general, copper tubes with high corrosion resistance, high thermal conductivity and high mechanical properties for the transfer of pressurized fluids are used in industry. When the copper pipe is being bended, wrinkles and wall thinning, and ovalization occurs in the pipe. In this study, a double ball mandrel was designed to improve the thickness reduction rate and the circular deformation rate, which occurs when bending the copper tube. The performance of the bending system with double ball mandrel has been verified by the simulation that is performed by using Deform 3D to compare with the thickness reduction rate and the circular deformation rate according to the bending angle of the soft material. As the result of simulation, it has been verified that it can reduce the circular deformation rate and damage value on the upper side of the pipe.
- 31 August 2020
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 24 (4) , 83-88
A Study on Characteristics of Bending Deformation for the Copper Pipe by Double Ball Mandrel
In general, copper tubes with high corrosion resistance, high thermal conductivity and high mechanical properties for the transfer of pressurized fluids are used in industry. When the copper pipe is being bended, wrinkles and wall thinning, and ovalization occurs in the pipe. In this study, a double ball mandrel was designed to improve the thickness reduction rate and the circular deformation rate, which occurs when bending the copper tube. The performance of the bending system with double ball mandrel has been verified by the simulation that is performed by using Deform 3D to compare with the thickness reduction rate and the circular deformation rate according to the bending angle of the soft material. As the result of simulation, it has been verified that it can reduce the circular deformation rate and damage value on the upper side of the pipe.
- 31 December 2019
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 23 (6) , 32-38
A Study on the Sources of Failure due to Change in Coolant Temperature in Petrol Engines
The effect of cooling water on internal combustion engine vehicles has a great effect on the environmental as well as the mechanical. In order to quickly find the cause of failure of the cooling water system for vehicle, various analyses of cooling water temperature are required in the event of failure of the critical components of the cooling water system. Therefore, there is a problem that the lots of cooling devices should be serviced to determine the exact cause. In this study, the components of analysis system was designed considering various operating times and the failure area of the cooling water thermostatic, the high and low speed cooling fan. Experimental results showed that rapid analysis of the failure parts of the cooling water line was possible without disassembling and assembling the parts in the cooling water system.
- 31 December 2019
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 23 (6) , 32-38
A Study on the Sources of Failure due to Change in Coolant Temperature in Petrol Engines
The effect of cooling water on internal combustion engine vehicles has a great effect on the environmental as well as the mechanical. In order to quickly find the cause of failure of the cooling water system for vehicle, various analyses of cooling water temperature are required in the event of failure of the critical components of the cooling water system. Therefore, there is a problem that the lots of cooling devices should be serviced to determine the exact cause. In this study, the components of analysis system was designed considering various operating times and the failure area of the cooling water thermostatic, the high and low speed cooling fan. Experimental results showed that rapid analysis of the failure parts of the cooling water line was possible without disassembling and assembling the parts in the cooling water system.
- 30 June 2019
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 23 (3) , 51-56
A study on Characteristics of Bending Deformation for the Copper Pipe
- 30 June 2019
- Published by The Korea Society for Power System Engineering in Journal of Power System Engineering
- Vol. 23 (3) , 51-56
A study on Characteristics of Bending Deformation for the Copper Pipe