RPRetno Wigajatri Purnamaningsih

Retno Wigajatri Purnamaningsih

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Retno Wigajatri Purnamaningsih has a total of 41 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Statistical Framework for Nonlinear Calibration of a Single FBG Sensor Under Coupled Pressure–Temperature Loading

    by Reza Diharja, Sasono Rahardjo, Retno Wigajatri Purnamaningsih

    Fiber Bragg Grating (FBG) sensors are widely used to measure pressure and temperature. However, when both are subjected to a coupled environment, the Bragg wavelengths influence each other, causing biased measurements if not properly calibrated. Most calibration models assume linear sensitivity, which may not hold across the entire operating range. This study proposes a five-step statistical calibration framework for a single FBG sensor under coupled pressure–temperature conditions: data preparation; fitting linear, quadratic, and cubic models; model selection using AIC/BIC; local sensitivity calculation; and contribution decomposition via Response Surface Methodology (RSM). The framework was tested on experimental data from an FBG sensor mounted on a metal membrane, at pressures of 0 MPa–2.0 MPa and temperatures of 5 °C–45 °C. Nonlinear models outperformed linear ones, with R¯2 values of 0.9725–0.9992. The model was validated using Leave-One-Out Cross-Validation (LOOCV), yielding an out-of-sample RMSE (Root Mean Square Error) of 0.0452 nm. Pressure sensitivity remained constant at 0.2250 nm/MPa, while temperature sensitivity decreased from 0.0224 nm/°C at 5 °C to 0.0069 nm/°C at 45 °C. RSM showed that pressure influences the slope and temperature influences the offset, with no significant interaction. Residual analysis satisfied the regression assumptions, and the combined uncertainty (0.008 nm/MPa; 0.0003 nm/°C) was much smaller than the observed sensitivity range, confirming that the variations are physical, not instrument noise. This framework is practical and statistically sound for single FBG sensor calibration.

  • Consistency Evaluation of a Three-Axis Fiber Bragg Grating Accelerometer Sensor for AUV Thruster Vibration Measurement

    by Muhammad Alif Rahman Sukapraja, Sasono Rahardjo, Retno Wigajatri Purnamaningsih, Maristya Rahmadiansyah, Mustika Fitriana Dewi, Tinova Pramudya

  • Measurement of Hydrostatic Pressure 0–5 kg/cm2 Using a Fiber Bragg Grating Sensor Integrated with a 304 Stainless Steel Diaphragm

    by Rafi Kamil Arief, Maratul Hamidah, Muhammad Yusha Firdaus, Sasono Rahardjo, Retno Wigajatri Purnamaningsih

  • Open Access

    Development of a 1550 nm LiDAR System Using Galvanometer and i-ToF Method for Distance Measurement and 2D Object Reconstruction

    by Febrian Winston Hutagalung, Retno Wigajatri Purnamaningsih, Sahat Pandapotan Nainggolan, Mefina Yulias Rofianingrum, Asep Hapiddin, Dwi Hanto

    LiDAR (Light Detection and Ranging) is a high-precision distance measurement technology based on laser light reflection. This study develops a galvanometer-based LiDAR system utilizing the indirect Time of Flight (i-ToF) method with 100 MHz sinusoidal modulation and a 1550 nm eye-safe laser diode. The system is designed to measure distance and identify the shape of 2D objects. The system was tested through phase difference measurements, galvanometer response, and flat-surface mapping at distances of 25 cm and 35 cm. The measurement results demonstrate high linearity and stability up to a maximum range of 1.5 meters, in accordance with the 360° phase difference (∆φ) limitation. The measurements of object dimensions in the form of an aluminum foil-covered plate at distances of 25 cm (1.76 cm × 2.63 cm) and 35 cm (2.45 cm × 3.66 cm) indicate that increasing the distance between the object and the system results in a wider coverage area but with reduced spatial resolution. At a distance of 25 cm, the light beam shifts by 0.436 cm/1°∆φ, whereas at 35 cm it shifts by 0.611 cm/1°∆φ. Furthermore, the limited active area of the photodetector was identified as the main factor restricting the detection coverage. This research opens opportunities for further development, particularly in optimizing galvanometer angle adjustments and enhancing the photodetector’s active area to expand coverage and improve measurement accuracy under various operating conditions.

  • Open Access

    Analysis of Bare Uniform Fiber Bragg Grating Sensor for Measuring Strain on the Landing Gear of the LSU-02 Unmanned Aircraft

    by Rudi Choirul Anwar, Retno Wigajatri Purnamaningsih, Sasono Rahardjo, Maratul Hamidah, Aryandi Martha, Muhammad Yusha Firdaus, Tinova Pramudya

    This paper reports the results of testing a bare uniform FBG sensor for measuring strain occurring on the landing gear of an unmanned aircraft. The landing gear used in this research is made from carbon fiber, known for its high strength and stiffness. The FBG sensor is positioned 20 cm from the center point of the landing gear, specifically at the curved section, to optimize strain detection. Static testing to measure strain was conducted by applying varying mass loads from 0 to 9 kilograms to test the sensor's response to load changes. Measurement results show a constant measurement threshold at a load of 50 grams, indicating sensor stability within that load range, with a measurement resolution of 0.1654 microstrain. Comparison of FBG measurement results with the BLFAB-55 strain gauge sensor revealed a measurement difference of 5.9%. Further research was conducted by introducing disturbances in the form of wind at speeds of 5 m/s and 10 m/s, and temperature disturbances of 30°C and 45°C. The results showed that the 45°C temperature disturbance had the most significant impact on the strain changes measured by the FBG, with an increase in strain value of 265% compared to when there was no disturbance.


  • Detection of Low Hydrostatic Pressure Using Fiber Bragg Grating Sensor

    by Naufal Aiman Madani, Retno Wigajatri Purnamaningsih, Nji Raden Poespawati, Maratul Hamidah, Sasono Rahardjo, Dena Karunianto Wibowo

    The aim of this study was to investigate the detection of low hydrostatic pressure, serving as the foundation for developing an underwater pressure sensor. This included creating a single-mode, uniformly structured Fiber Bragg Grating (FBG) with a stainless-steel coating. The experiment included loading the sensor with different volumes of fresh water ranging from 0 ml to 6 ml, in increments of 0.25 ml, in the perpendicular vertical direction. This volume range corresponded to hydrostatic pressures ranging from 0 Pa to 40.55 Pa. The experimental results showed a consistent linear relationship between low hydrostatic pressure and Bragg wavelength, implying a sensitivity of 0.8092 pm/Pa, according to theoretical expectations. Subsequently, mathematical simulations were conducted based on the results to predict the sensor performance under various potential seabed temperatures. The simulation results indicated that as the temperature rose, there was a corresponding increase in the reflected wavelength difference by 5.3754 ×10-9 nm/Pa for every 1°C increase in seawater temperature.


  • Open Access

    Water Temperature Measurement Using Fiber Bragg Grating

    by Irwan Kustianto, Retno Wigajatri Purnamaningsih, Sasono Rahardjo, Maratul Hamidah, Muhammad Yusha Firdaus

    Temperature measurement in water is crucial for various applications and technological advancements. Fiber Bragg Grating (FBG) sensors have shown significant potential in measuring water temperature, with advantages in accuracy, reliability, and resistance to extreme environmental conditions. In this study, we conducted a series of experiments to measure water temperature in the range of 4 to 25 degrees Celsius using FBG sensors. Through two experimental analyses of the FBG sensor's response to water temperature changes, we found that the sensitivity of the FBG sensor we used was 0.0101 nm/°C. The results of this research demonstrate that FBG sensors are capable of measuring water temperature with high sensitivity, accuracy, and stability.


  • Open Access

    Design of a Four-Branch Optical Power Splitter Based on Gallium-Nitride Using Rectangular Waveguide Coupling for Telecommunication Links

    by Retno W. Purnamaningsih, Nji R. Poespawati, Elhadj Dogheche

    This paper reports design of a simple four-branch optical power splitter using five parallel rectangular waveguides coupling in a gallium-nitride (GaN) semiconductor/sapphire for telecommunication links. The optimisation was conducted using the 3D FD-BPM method for long wavelength optical communication. The result shows that, at propagation length of 925 μm, the optical power input was successfully split into four uniform output beams, each with 24% of total input power. It is also shown that the relative output power distribution is almost stable through the C-band range. At the operating wavelength of 1.55 μm, the proposed power splitter has an excess loss lower than 0.2 dB. This study demonstrates the opportunity to develop optical interconnections from UV-Visible to near IR wavelengths.


  • Open Access

    An Optical Power Divider Based on Mode Coupling Using GaN/Al2O3 for Underwater Communication †

    by Retno Wigajatri Purnamaningsih, Nji Raden Poespawati, Tomy Abuzairi, Elhadj Dogheche

    This paper details the design of a 1 × 8 optical power divider, using a gallium nitride (GaN) semiconductor on sapphire, which can be applied to underwater optical wireless communication. The design consists of nine parallel rectangular waveguides which are based on mode coupling phenomena. Analysis of the design was performed using the beam propagation method (BPM). The optimization was conducted using the 3D finite difference (FD)-BPM method with an optical signal input at the wavelength required for maritime application of λ = 0.45 µm. The signal was injected into the central waveguide. The results showed that at a propagation length of 1480 µm the optical power is divided into eight output beams with an excess loss of 0.46 dB and imbalance of 0.51 dB. The proposed design can be further developed and applied in future underwater communication technology.


  • Weight monitoring system for newborn incubator application

    by Arif Widianto, Intan Nurfitri, Pradipta Mahatidana, Tomy Abuzairi, N. R. Poespawati, Retno W. Purnamaningsih.

    We proposed weight monitoring system using load cell sensor for newborn incubator application. The weight sensing system consists of a load cell, conditioning signal circuit, and microcontroller Arduino Uno R3. The performance of the sensor was investigated by using the various weight from 0 up to 3000 g. Experiment results showed that this system has a small error of 4.313% and 12.5 g of threshold and resolution value. Compared to the typical baby scale available in local market, the proposed system has a lower error value and hysteresis.