SRShao-Shi Rui
Shao-Shi Rui
*This is an algorithmically generated author record based on publicly available information.
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shao-Shi Rui has a total of 105 co-authors. Here are the top co-authors by number of shared publications:
- Hui-Ji Shi
Department of Engineering Mechanics, Tsinghua University, Beijing 100084, China
8 shared publications - Chengqi Sun
State Key Laboratory of Nonlinear Mechanics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China
6 shared publications Xianfeng Ma
6 shared publicationsYue Su
6 shared publications- Li-Sha Niu
AML, Department of Engineering Mechanics, Tsinghua University , Beijing 100084, China
5 shared publications Qi-Nan Han
5 shared publications
Latest Publications
- Open Access
- 29 August 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 44, 4109-4119
Influence of compressive creep and creep fatigue on mechanical behavior of Ti-6Al-4V ELI titanium alloy at room temperature
- 29 August 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 44, 4109-4119
Open AccessInfluence of compressive creep and creep fatigue on mechanical behavior of Ti-6Al-4V ELI titanium alloy at room temperature
- Open Access
Fatigue Failure Mechanism and Crack Growth Behavior of Ti-6Al-4V ELI Titanium Alloy Welded Joints
Titanium alloy welded joints are key parts of deep-sea pressure hulls, which are subjected to fatigue loadings in service. In this study, axial fatigue tests, mode I fatigue crack growth tests, and mixed-mode I–II fatigue crack growth tests were conducted on the Ti-6Al-4V ELI titanium alloy welded joint, and its fatigue failure mechanism and crack growth behavior is investigated and compared with the base material. The results show that the S–N curve of Ti-6Al-4V ELI titanium alloy welded joints has a very similar slope as the base material, but its fatigue performance is lower than the base material. However, the welded joints exhibit a higher resistance in the near-threshold region under mode I loading compared to the base material. Scanning electron microscope observation indicates that the fatigue crack mainly initiates from gas pores during welding for the Ti-6Al-4V ELI titanium alloy welded joints. Under mixed-mode I–II loading, the stress intensity factor range component of welded joints is higher than that of the base material, and an equivalent stress intensity factor range model is proposed to describe the crack growth rate under both mode I and mixed-mode I–II loadings. The new model incorporates a parameter dependent on the mode mixity ratio defined by in this paper, and it unifies the crack growth data well under mode I and mixed-mode I–II loadings. The paper indicates that the gas pores during welding are an important factor for the poor fatigue performance of Ti-6Al-4V ELI titanium alloy welded joints.Open AccessFatigue Failure Mechanism and Crack Growth Behavior of Ti-6Al-4V ELI Titanium Alloy Welded Joints
Titanium alloy welded joints are key parts of deep-sea pressure hulls, which are subjected to fatigue loadings in service. In this study, axial fatigue tests, mode I fatigue crack growth tests, and mixed-mode I–II fatigue crack growth tests were conducted on the Ti-6Al-4V ELI titanium alloy welded joint, and its fatigue failure mechanism and crack growth behavior is investigated and compared with the base material. The results show that the S–N curve of Ti-6Al-4V ELI titanium alloy welded joints has a very similar slope as the base material, but its fatigue performance is lower than the base material. However, the welded joints exhibit a higher resistance in the near-threshold region under mode I loading compared to the base material. Scanning electron microscope observation indicates that the fatigue crack mainly initiates from gas pores during welding for the Ti-6Al-4V ELI titanium alloy welded joints. Under mixed-mode I–II loading, the stress intensity factor range component of welded joints is higher than that of the base material, and an equivalent stress intensity factor range model is proposed to describe the crack growth rate under both mode I and mixed-mode I–II loadings. The new model incorporates a parameter dependent on the mode mixity ratio defined by in this paper, and it unifies the crack growth data well under mode I and mixed-mode I–II loadings. The paper indicates that the gas pores during welding are an important factor for the poor fatigue performance of Ti-6Al-4V ELI titanium alloy welded joints. - 13 April 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 341
Fatigue properties and influential factors of Ti-6Al-4V ELI titanium alloy used in deep-sea pressure hull structure
- 13 April 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 341
Fatigue properties and influential factors of Ti-6Al-4V ELI titanium alloy used in deep-sea pressure hull structure
- 5 December 2025
- Published by Elsevier in International Journal of Fatigue
- Vol. 205
The effect of solution treatment temperature on the fretting fatigue of additively manufactured superalloys
- 5 December 2025
- Published by Elsevier in International Journal of Fatigue
- Vol. 205
The effect of solution treatment temperature on the fretting fatigue of additively manufactured superalloys
- 7 December 2024
- Published by Elsevier in International Journal of Fatigue
- Vol. 193
Fatigue failure mechanisms and influential factors for aluminum alloy and its welded joint in a high-speed train
- 7 December 2024
- Published by Elsevier in International Journal of Fatigue
- Vol. 193
Fatigue failure mechanisms and influential factors for aluminum alloy and its welded joint in a high-speed train
- 1 July 2024
- Published by Elsevier in Scripta Materialia
- Vol. 252
Investigation on the incipient plasticity of 〈001〉-oriented CoCrFeNi micropillar
- 1 July 2024
- Published by Elsevier in Scripta Materialia
- Vol. 252
Investigation on the incipient plasticity of 〈001〉-oriented CoCrFeNi micropillar
- 26 June 2024
- Published by Elsevier in International Journal of Plasticity
- Vol. 180
Unveiling the deformation micro-mechanism for mechanical anisotropy of a CoCrFeNi medium entropy alloy
- 26 June 2024
- Published by Elsevier in International Journal of Plasticity
- Vol. 180
Unveiling the deformation micro-mechanism for mechanical anisotropy of a CoCrFeNi medium entropy alloy