R P O'HAra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
R P O'HAra has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Anthony N. Palazotto
Air Force Institute of Technology, Wright-Patterson AFB, Dayton, OH 45433, USA
1 shared publication - Brian Runyon
Air Force Research Laboratory, Aerospace Systems Directorate , Wright-Patterson AFB, OH 45433
1 shared publication - Casey Holycross
Air Force Research Laboratory Aerospace Systems Directorate, Wright-Patterson AFB, OH 45433
1 shared publication - Luke Sheridan
Air Force Research Laboratory
1 shared publication - Onome Scott-Emuakpor
Air Force Research Laboratory, Aerospace Systems Directorate , Wright-Patterson AFB, OH 45433
1 shared publication - Tommy George
Mem. ASME Air Force Research Laboratory, Aerospace Systems Directorate, Wright-Patterson AFB, OH 45433
1 shared publication
Latest Publications
- 29 January 2020
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 142 (3)
Assessing Additive Manufacturing Repeatability of Inherently Damped Nickel Alloy Components
The repeatability of an additive manufacturing (AM) process that fabricates a unique specimen with inherent damping capability is explored. A laser powder bed fusion (LPBF) technique is used to additively manufacture nickel alloy components with the same geometry/dimensions. Key aspects to the manufacturing process such as scan strategy and build orientation are observed alongside damping performance. The results from forced-response testing show repeatable correlation between damping performance and modal response information. Furthermore, despite different scan strategies and build sequences, the results demonstrate that inherent damping repeatability is driven by the unique component geometry and has minimal sensitivity to manufacturing.
- 29 January 2020
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 142 (3)
Assessing Additive Manufacturing Repeatability of Inherently Damped Nickel Alloy Components
The repeatability of an additive manufacturing (AM) process that fabricates a unique specimen with inherent damping capability is explored. A laser powder bed fusion (LPBF) technique is used to additively manufacture nickel alloy components with the same geometry/dimensions. Key aspects to the manufacturing process such as scan strategy and build orientation are observed alongside damping performance. The results from forced-response testing show repeatable correlation between damping performance and modal response information. Furthermore, despite different scan strategies and build sequences, the results demonstrate that inherent damping repeatability is driven by the unique component geometry and has minimal sensitivity to manufacturing.
- 23 October 2012
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 7 (4) , 046011
The morphological characterization of the forewing of theManduca sextaspecies for the application of biomimetic flapping wing micro air vehicles
To properly model the structural dynamics of the forewing of the Manduca sexta species, it is critical that the material and structural properties of the biological specimen be understood. This paper presents the results of a morphological study that has been conducted to identify the material and structural properties of a sample of male and female Manduca sexta specimens. The average mass, area, shape, size and camber of the wing were evaluated using novel measurement techniques. Further emphasis is placed on studying the critical substructures of the wing: venation and membrane. The venation cross section is measured using detailed pathological techniques over the entire venation of the wing. The elastic modulus of the leading edge veins is experimentally determined using advanced non-contact structural dynamic techniques. The membrane elastic modulus is randomly sampled over the entire wing to determine global material properties for the membrane using nanoindentation. The data gathered from this morphological study form the basis for the replication of future finite element structural models and engineered biomimetic wings for use with flapping wing micro air vehicles.
- 23 October 2012
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 7 (4) , 046011
The morphological characterization of the forewing of theManduca sextaspecies for the application of biomimetic flapping wing micro air vehicles
To properly model the structural dynamics of the forewing of the Manduca sexta species, it is critical that the material and structural properties of the biological specimen be understood. This paper presents the results of a morphological study that has been conducted to identify the material and structural properties of a sample of male and female Manduca sexta specimens. The average mass, area, shape, size and camber of the wing were evaluated using novel measurement techniques. Further emphasis is placed on studying the critical substructures of the wing: venation and membrane. The venation cross section is measured using detailed pathological techniques over the entire venation of the wing. The elastic modulus of the leading edge veins is experimentally determined using advanced non-contact structural dynamic techniques. The membrane elastic modulus is randomly sampled over the entire wing to determine global material properties for the membrane using nanoindentation. The data gathered from this morphological study form the basis for the replication of future finite element structural models and engineered biomimetic wings for use with flapping wing micro air vehicles.