Tatsuhiro Takahashi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tatsuhiro Takahashi has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Masumi Takamura
Yamagata University Inkjet Development Center, 1- 808-48 Arcadia, Yonezawa 992-0119, Japan
3 shared publications - Ryoma Tokonami
Graduate School of Organic Materials Science Yamagata University Yamagata Japan
3 shared publications - Teruya Goto
Department of Organic Materials Science, Graduated School of Organic Materials Science, Yamagata University, 4-3-16 Jonan, Yonezawa 992-8510, Yamagata, Japan
3 shared publications - Eri Oishi
Department of Organic Materials Science, Graduated School of Organic Materials Science, Yamagata University, 4-3-16 Jonan, Yonezawa 992-8510, Yamagata, Japan
2 shared publications - Kiadtisak Saenboonruang
Special Research Unit of Radiation Technology for Advanced Materials (RTAM), Faculty of Science, Kasetsart University, Bangkok 10900, Thailand
2 shared publications Masahiro Hosoda
Hirosaki University Graduate School of Health Sciences, 66-1 Hon-cho, Hirosaki, Aomori 036-8564, Japan
2 shared publications
Latest Publications
- Open Access
- 17 October 2026
- Published by Wiley in Polymer Composites
Effects of Two Types of Multi‐Walled Carbon Nanotubes Used for Carbon Fiber Surface Modification on Tensile Properties of Polycarbonate Composites
In this study, carbon fibers (CFs) coated with two types of multi‐walled carbon nanotubes (MWCNTs), manufactured by Nanocyl SA (MWCNT‐a) or TPR Co. Ltd. (MWCNT‐b), were prepared using a reactive polymer, and the effects of the coated MWCNTs on the tensile properties of polycarbonate (PC) composites were investigated. The MWCNT‐coated CFs were prepared through a simple three‐step process. First, a reactive layer of poly(2‐isopropenyl‐2‐oxazoline) (Pipozo) was formed on the CF surface as the first layer. Next, the two MWCNT dispersions were coated onto the Pipozo‐coated CFs to form the second layer. An additional Pipozo layer was then formed as the third layer. Scanning electron microscopy (SEM) observations revealed qualitative differences in coating morphology between the two systems. A quantitative analysis showed that the coating amounts of MWCNT‐a and MWCNT‐b were 0.16 ± 0.017 wt.% and 0.12 ± 0.007 wt.%, respectively. The MWCNT‐b system exhibited the highest mean values among the CF‐containing composites. Fracture‐surface SEM revealed PC resin residue on the treated CF surfaces, indicating partial fracture within the adjacent PC matrix. These results suggest that both the Pipozo‐derived interphase and retained MWCNT coating morphology may be important in the interfacial design of CF‐reinforced thermoplastic composites.
- 17 October 2026
- Published by Wiley in Polymer Composites
Open AccessEffects of Two Types of Multi‐Walled Carbon Nanotubes Used for Carbon Fiber Surface Modification on Tensile Properties of Polycarbonate Composites
In this study, carbon fibers (CFs) coated with two types of multi‐walled carbon nanotubes (MWCNTs), manufactured by Nanocyl SA (MWCNT‐a) or TPR Co. Ltd. (MWCNT‐b), were prepared using a reactive polymer, and the effects of the coated MWCNTs on the tensile properties of polycarbonate (PC) composites were investigated. The MWCNT‐coated CFs were prepared through a simple three‐step process. First, a reactive layer of poly(2‐isopropenyl‐2‐oxazoline) (Pipozo) was formed on the CF surface as the first layer. Next, the two MWCNT dispersions were coated onto the Pipozo‐coated CFs to form the second layer. An additional Pipozo layer was then formed as the third layer. Scanning electron microscopy (SEM) observations revealed qualitative differences in coating morphology between the two systems. A quantitative analysis showed that the coating amounts of MWCNT‐a and MWCNT‐b were 0.16 ± 0.017 wt.% and 0.12 ± 0.007 wt.%, respectively. The MWCNT‐b system exhibited the highest mean values among the CF‐containing composites. Fracture‐surface SEM revealed PC resin residue on the treated CF surfaces, indicating partial fracture within the adjacent PC matrix. These results suggest that both the Pipozo‐derived interphase and retained MWCNT coating morphology may be important in the interfacial design of CF‐reinforced thermoplastic composites.
- Open Access
- 15 September 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (22)
Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles
A carbon‐fiber‐reinforced plastic (CFRP) with enhanced through‐thickness electrical conductivity is developed by incorporating spherical graphite particles (GPs). The introduction of large spherical GPs reduces interparticle contact resistance in the low‐viscosity uncured resin required for carbon‐fiber (CF) fabric impregnation while maintaining the viscosity within a range suitable for fabric impregnation (≤19.0 Pa s at 30 vol%), thereby providing favorable processing conditions during composite fabrication. Because the particle size was intentionally selected to be larger than the interfiber spacing ( D 50 = 8 μm), the GPs remain at the interfaces between CF layers rather than penetrating into the fiber bundles. Under compressive pressure during molding, the GPs promote closer contact between CFs. Consequently, the number of CFs per unit area within the CF layer increases by a factor of 1.4 relative to that in the GP‐free system, resulting in a distinctive alternating CF/GP layered architecture through the thickness. This structural arrangement substantially increased the through‐thickness electrical conductivity from 4.5 × 10 − 3 S/cm for GP‐free CFRP to 8.1 × 10 − 1 S/cm for GP‐containing CFRP. These findings demonstrate that the deliberate use of large‐diameter GPs enables the formation of a CF/GP layered structure, thereby markedly enhancing the through‐thickness electrical conductivity of CFRP.
- 15 September 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (22)
Open AccessEnhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles
A carbon‐fiber‐reinforced plastic (CFRP) with enhanced through‐thickness electrical conductivity is developed by incorporating spherical graphite particles (GPs). The introduction of large spherical GPs reduces interparticle contact resistance in the low‐viscosity uncured resin required for carbon‐fiber (CF) fabric impregnation while maintaining the viscosity within a range suitable for fabric impregnation (≤19.0 Pa s at 30 vol%), thereby providing favorable processing conditions during composite fabrication. Because the particle size was intentionally selected to be larger than the interfiber spacing ( D 50 = 8 μm), the GPs remain at the interfaces between CF layers rather than penetrating into the fiber bundles. Under compressive pressure during molding, the GPs promote closer contact between CFs. Consequently, the number of CFs per unit area within the CF layer increases by a factor of 1.4 relative to that in the GP‐free system, resulting in a distinctive alternating CF/GP layered architecture through the thickness. This structural arrangement substantially increased the through‐thickness electrical conductivity from 4.5 × 10 − 3 S/cm for GP‐free CFRP to 8.1 × 10 − 1 S/cm for GP‐containing CFRP. These findings demonstrate that the deliberate use of large‐diameter GPs enables the formation of a CF/GP layered structure, thereby markedly enhancing the through‐thickness electrical conductivity of CFRP.
- Open Access
- 9 August 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (16) , 7133
Eco-Friendly Synthesis of Silver Nanoparticles Using Punica granatum (Pomegranate) Peel Extract Under Chemical-Free and Ambient Conditions: Characterization and Antibacterial Activity
In this work, a simple chemical- and thermal-free procedure was developed for the green synthesis of AgNPs using pomegranate (Punica granatum) peel extract as both reducing and stabilizing agents under ambient conditions. The pomegranate extract exhibited a high total phenolic content of 126.37 ± 5.29 mg GAE/g DW, indicating the abundance of bioactive phytochemicals capable of promoting nanoparticle formation. The synthesis parameters were optimized by varying reaction time and extract concentration, with the optimum conditions identified as 18 mg/mL extract concentration and 48 h reaction time based on UV–Vis analyses. The synthesized AgNPs at the optimized condition exhibited a characteristic surface plasmon resonance band at 430–440 nm and were predominantly quasi-spherical with an average particle size of 36.9 ± 14.2 nm determined by TEM. Dynamic light scattering (DLS) analysis yielded an intensity-weighted average hydrodynamic diameter of 72.5 ± 2.4 nm, while the number-weighted distribution confirmed that the suspension was predominantly composed of smaller nanoparticles that were consistent with the TEM observations. The synthesized AgNPs also exhibited a zeta potential of −33.5 ± 0.6 mV, indicating good colloidal stability. XRD and EDX analyses confirmed the formation of crystalline metallic AgNPs, while FTIR results suggested the involvement of phytochemicals in nanoparticle stabilization. The AgNPs also showed concentration-dependent antibacterial activity against E. coli and S. aureus, with MIC (MBC) values of 18.75 (37.5) and 9.375 (150) µg/mL, respectively. In addition, the cytotoxicity assessment using L929 fibroblasts yielded an IC50 value of 86 µg/mL, with a selectivity index of 4.59 and 9.17 against E. coli and S. aureus, respectively, indicating an excellent degree of preferential toxicity toward bacterial cells.
- 9 August 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (16) , 7133
Open AccessEco-Friendly Synthesis of Silver Nanoparticles Using Punica granatum (Pomegranate) Peel Extract Under Chemical-Free and Ambient Conditions: Characterization and Antibacterial Activity
In this work, a simple chemical- and thermal-free procedure was developed for the green synthesis of AgNPs using pomegranate (Punica granatum) peel extract as both reducing and stabilizing agents under ambient conditions. The pomegranate extract exhibited a high total phenolic content of 126.37 ± 5.29 mg GAE/g DW, indicating the abundance of bioactive phytochemicals capable of promoting nanoparticle formation. The synthesis parameters were optimized by varying reaction time and extract concentration, with the optimum conditions identified as 18 mg/mL extract concentration and 48 h reaction time based on UV–Vis analyses. The synthesized AgNPs at the optimized condition exhibited a characteristic surface plasmon resonance band at 430–440 nm and were predominantly quasi-spherical with an average particle size of 36.9 ± 14.2 nm determined by TEM. Dynamic light scattering (DLS) analysis yielded an intensity-weighted average hydrodynamic diameter of 72.5 ± 2.4 nm, while the number-weighted distribution confirmed that the suspension was predominantly composed of smaller nanoparticles that were consistent with the TEM observations. The synthesized AgNPs also exhibited a zeta potential of −33.5 ± 0.6 mV, indicating good colloidal stability. XRD and EDX analyses confirmed the formation of crystalline metallic AgNPs, while FTIR results suggested the involvement of phytochemicals in nanoparticle stabilization. The AgNPs also showed concentration-dependent antibacterial activity against E. coli and S. aureus, with MIC (MBC) values of 18.75 (37.5) and 9.375 (150) µg/mL, respectively. In addition, the cytotoxicity assessment using L929 fibroblasts yielded an IC50 value of 86 µg/mL, with a selectivity index of 4.59 and 9.17 against E. coli and S. aureus, respectively, indicating an excellent degree of preferential toxicity toward bacterial cells.
- Open Access
- 5 January 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (1) , 549
Valorizing Rice Husk Waste as a Biosorbent with Gamma-Induced Surface Modification for Enhanced Heavy-Metal Adsorption
This work investigated the effects of gamma irradiation on the adsorption capacities of rice husk (RH) for the removal of Cu2+, Cr3+, and Zn2+ ions from aqueous solutions, with potential applications in wastewater remediation. RH samples were gamma-irradiated at doses up to 40 kGy and characterized using SEM-EDS, XRF, FTIR, XRD, and BET analyses. While morphological and textural changes remained subtle, FTIR and SEM-EDS confirmed the formation and intensification of oxygen-containing functional groups, including –OH, –COOH, and C=O, as well as increased exposure of silica (Si–O) on the surfaces, which substantially enhanced surface reactivity of RH toward metal ions. Batch adsorption experiments revealed that 40-kGy irradiated RH samples (RH-40) exhibited the highest removal efficiencies compared to non-irradiated and lower-dose samples (RH-0, RH-10, RH-20, and RH-30), specifically with improvements of 415% for Cu2+, 502% for Cr3+, and 663% for Zn2+ compared to RH-0, determined at the initial concentration of 10 mg/L. Kinetic studies also showed rapid adsorption within the first 10–15 min, dominated initially by boundary-layer diffusion, followed by chemisorption-driven equilibrium behavior. The pseudo-second-order (PSO) model provided an excellent fit for all metals (R2 = 0.999), indicating maximum model-predicted kinetic capacities of 555.56 mg/g (Cu2+), 769.23 mg/g (Cr3+), and 434.78 mg/g (Zn2+). Langmuir isotherms also fitted well (R2 = 0.941–0.995), with predicted monolayer capacities of 535.33 mg/g (Cu2+), 491.64 mg/g (Cr3+), and 318.88 mg/g (Zn2+). Freundlich modeling further indicated favorable heterogeneous adsorption, with KF values of 42.614 (Zn2+), 20.443 (Cr3+), and 16.524 (Cu2+) and heterogeneity factors (n) greater than 1 for all metals. These overall results suggested that gamma irradiation substantially enhanced RH functionality that enabled fast and high-capacity heavy-metal adsorption through surface oxidation and carbon valorization. Gamma-irradiated RH, therefore, represented a promising, low-cost, and environmentally friendly biosorbent for wastewater treatment applications.
- 5 January 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (1) , 549
Open AccessValorizing Rice Husk Waste as a Biosorbent with Gamma-Induced Surface Modification for Enhanced Heavy-Metal Adsorption
This work investigated the effects of gamma irradiation on the adsorption capacities of rice husk (RH) for the removal of Cu2+, Cr3+, and Zn2+ ions from aqueous solutions, with potential applications in wastewater remediation. RH samples were gamma-irradiated at doses up to 40 kGy and characterized using SEM-EDS, XRF, FTIR, XRD, and BET analyses. While morphological and textural changes remained subtle, FTIR and SEM-EDS confirmed the formation and intensification of oxygen-containing functional groups, including –OH, –COOH, and C=O, as well as increased exposure of silica (Si–O) on the surfaces, which substantially enhanced surface reactivity of RH toward metal ions. Batch adsorption experiments revealed that 40-kGy irradiated RH samples (RH-40) exhibited the highest removal efficiencies compared to non-irradiated and lower-dose samples (RH-0, RH-10, RH-20, and RH-30), specifically with improvements of 415% for Cu2+, 502% for Cr3+, and 663% for Zn2+ compared to RH-0, determined at the initial concentration of 10 mg/L. Kinetic studies also showed rapid adsorption within the first 10–15 min, dominated initially by boundary-layer diffusion, followed by chemisorption-driven equilibrium behavior. The pseudo-second-order (PSO) model provided an excellent fit for all metals (R2 = 0.999), indicating maximum model-predicted kinetic capacities of 555.56 mg/g (Cu2+), 769.23 mg/g (Cr3+), and 434.78 mg/g (Zn2+). Langmuir isotherms also fitted well (R2 = 0.941–0.995), with predicted monolayer capacities of 535.33 mg/g (Cu2+), 491.64 mg/g (Cr3+), and 318.88 mg/g (Zn2+). Freundlich modeling further indicated favorable heterogeneous adsorption, with KF values of 42.614 (Zn2+), 20.443 (Cr3+), and 16.524 (Cu2+) and heterogeneity factors (n) greater than 1 for all metals. These overall results suggested that gamma irradiation substantially enhanced RH functionality that enabled fast and high-capacity heavy-metal adsorption through surface oxidation and carbon valorization. Gamma-irradiated RH, therefore, represented a promising, low-cost, and environmentally friendly biosorbent for wastewater treatment applications.
- 16 April 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (14) , 13496-13508
Effect of adding two kinds of acid‐terminated polypropylene and surface modification using tannic acid‐iron ion complex on the mechanical properties of carbon fiber/polypropylene composites
This study investigated the effect of maleic anhydride‐terminated polypropylene (PPtMA) or polyacrylic acid‐terminated polypropylene (PPtAA) addition and surface modification of carbon fibers (CFs) with a tannic acid (TA)‐Fe3+ complex on the mechanical properties of CF/polypropylene (PP) composites. The addition of PPtMA or PPtAA improved the mechanical properties. Examining the effects of the amount of PPtMA and PPtAA added (compared at 5 and 20 wt% in PP) revealed that the amount that resulted in good mechanical properties was different for PPtMA and PPtAA (PPtMA: 5 wt% in PP, PPtAA: 20 wt% in PP). The TA‐Fe3+ coating further enhanced these improvements. Scanning electron microscopic analysis revealed that the addition of compatibilizers improved interfacial adhesion. In addition, the combined use of compatibilizers and CFs coated with the TA‐Fe3+ complex showed particularly strong effects. Analysis by differential scanning calorimetry showed that adding a large amount of compatibilizer reduced the crystallinity; however, in the case of PPtAA, hydrogen bonding enhanced the rigidity of the matrix resin and improved the interfacial adhesion. Therefore, even at high PPtAA concentrations, the CF/PP composite containing CFs coated with the TA‐Fe3+ complex maintained good mechanical properties.Highlights: Carbon fiber/polypropylene composites were prepared with compatibilizers. Compatibilizers were PP terminated with maleic anhydride or polyacrylic acid. The addition of either compatibilizer resulted in good mechanical properties. The surface of CFs was also modified with a tannic acid (TA)‐Fe3+ complex. The compatibilizer + complex‐modified CFs improved interfacial adhesion.
- 16 April 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (14) , 13496-13508
Effect of adding two kinds of acid‐terminated polypropylene and surface modification using tannic acid‐iron ion complex on the mechanical properties of carbon fiber/polypropylene composites
This study investigated the effect of maleic anhydride‐terminated polypropylene (PPtMA) or polyacrylic acid‐terminated polypropylene (PPtAA) addition and surface modification of carbon fibers (CFs) with a tannic acid (TA)‐Fe3+ complex on the mechanical properties of CF/polypropylene (PP) composites. The addition of PPtMA or PPtAA improved the mechanical properties. Examining the effects of the amount of PPtMA and PPtAA added (compared at 5 and 20 wt% in PP) revealed that the amount that resulted in good mechanical properties was different for PPtMA and PPtAA (PPtMA: 5 wt% in PP, PPtAA: 20 wt% in PP). The TA‐Fe3+ coating further enhanced these improvements. Scanning electron microscopic analysis revealed that the addition of compatibilizers improved interfacial adhesion. In addition, the combined use of compatibilizers and CFs coated with the TA‐Fe3+ complex showed particularly strong effects. Analysis by differential scanning calorimetry showed that adding a large amount of compatibilizer reduced the crystallinity; however, in the case of PPtAA, hydrogen bonding enhanced the rigidity of the matrix resin and improved the interfacial adhesion. Therefore, even at high PPtAA concentrations, the CF/PP composite containing CFs coated with the TA‐Fe3+ complex maintained good mechanical properties.Highlights: Carbon fiber/polypropylene composites were prepared with compatibilizers. Compatibilizers were PP terminated with maleic anhydride or polyacrylic acid. The addition of either compatibilizer resulted in good mechanical properties. The surface of CFs was also modified with a tannic acid (TA)‐Fe3+ complex. The compatibilizer + complex‐modified CFs improved interfacial adhesion.
- Open Access
- 28 October 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (44) , 44770-44777
Transparent X-ray Shielding Solutions with Various Metal Ions
We fabricated transparent, Pb-free X-ray shielding materials using solvated ions in a polar solvent. Previous materials have been based on dispersions of metal-containing particles such as barium sulfate (BaSO4) in a matrix. Comparisons of suspensions of metal-based particles and solutions of metal ions in a solvent enable better understanding of interactions such as reflection, scattering, and absorption between X-rays and substances. The X-ray shielding properties of a solution of solvated metal ions were similar to or better than those of suspensions of metal-containing particles. In addition, the metal-ion solutions exhibited high transparency. The most effective material among those investigated for X-ray shielding was barium bromide (BaBr2), which exhibits high solubility in polar solvents. X-ray shielding of 92% was confirmed at a tube voltage of 120 kV, along with ∼90% UV transmittance at a visible-light wavelength of 400 nm. Thus, both high X-ray shielding performance and high transparency were achieved.
- 28 October 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (44) , 44770-44777
Open AccessTransparent X-ray Shielding Solutions with Various Metal Ions
We fabricated transparent, Pb-free X-ray shielding materials using solvated ions in a polar solvent. Previous materials have been based on dispersions of metal-containing particles such as barium sulfate (BaSO4) in a matrix. Comparisons of suspensions of metal-based particles and solutions of metal ions in a solvent enable better understanding of interactions such as reflection, scattering, and absorption between X-rays and substances. The X-ray shielding properties of a solution of solvated metal ions were similar to or better than those of suspensions of metal-containing particles. In addition, the metal-ion solutions exhibited high transparency. The most effective material among those investigated for X-ray shielding was barium bromide (BaBr2), which exhibits high solubility in polar solvents. X-ray shielding of 92% was confirmed at a tube voltage of 120 kV, along with ∼90% UV transmittance at a visible-light wavelength of 400 nm. Thus, both high X-ray shielding performance and high transparency were achieved.
- 28 September 2024
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 226 (4)
Flexible Composites of Barium Sulfate Modified by Tannic Acid Using Glycerol/Starch for X‐Ray Shielding Applications
This study investigates the X‐ray shielding properties and mechanical properties of barium sulfate (BaSO4) composites based on a biodegradable matrix composed of glycerol and starch. In addition, tannic acid (TA) is used for surface modification of the BaSO4. Increasing the amount of BaSO4 is necessary to improve the composite's X‐ray shielding properties; however, as the amount of BaSO4 increases, the composite becomes harder. The purpose of this research is to prepare a flexible X‐ray‐shielding composite even when a large amount of filler is added. TA easily coats the BaSO4 surface, and its presence is confirmed by Fourier transform infrared spectroscopy and thermogravimetric analysis. Elongation of the composites composed of glycerol, starch, and BaSO4 is increased by 50% because of the formation of hydrogen bonds between the hydroxyl groups of glycerol and starch and those of TA. Consequently, the fracture behavior changed from brittle fracture to ductile fracture. However, the X‐ray shielding properties are not changed by the surface modification with TA. The use of glycerol, starch, and BaSO4 is a new approach to the development of biodegradable radiation shielding materials. In addition, as a surface‐modification agent, TA is environmentally friendly. All of the composites are prepared from natural materials.
- 28 September 2024
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 226 (4)
Flexible Composites of Barium Sulfate Modified by Tannic Acid Using Glycerol/Starch for X‐Ray Shielding Applications
This study investigates the X‐ray shielding properties and mechanical properties of barium sulfate (BaSO4) composites based on a biodegradable matrix composed of glycerol and starch. In addition, tannic acid (TA) is used for surface modification of the BaSO4. Increasing the amount of BaSO4 is necessary to improve the composite's X‐ray shielding properties; however, as the amount of BaSO4 increases, the composite becomes harder. The purpose of this research is to prepare a flexible X‐ray‐shielding composite even when a large amount of filler is added. TA easily coats the BaSO4 surface, and its presence is confirmed by Fourier transform infrared spectroscopy and thermogravimetric analysis. Elongation of the composites composed of glycerol, starch, and BaSO4 is increased by 50% because of the formation of hydrogen bonds between the hydroxyl groups of glycerol and starch and those of TA. Consequently, the fracture behavior changed from brittle fracture to ductile fracture. However, the X‐ray shielding properties are not changed by the surface modification with TA. The use of glycerol, starch, and BaSO4 is a new approach to the development of biodegradable radiation shielding materials. In addition, as a surface‐modification agent, TA is environmentally friendly. All of the composites are prepared from natural materials.
- Open Access
Novel Chain-End Modification of Polymer Iodides via Reversible Complexation-Mediated Polymerization with Functionalized Radical Generation Agents
The modification of polymer chain ends is important in order to produce highly functional polymers. A novel chain-end modification of polymer iodides (Polymer-I) via reversible complexation-mediated polymerization (RCMP) with different functionalized radical generation agents, such as azo compounds and organic peroxides, was developed. This reaction was comprehensively studied for three different polymers, i.e., poly (methyl methacrylate), polystyrene and poly (n-butyl acrylate) (PBA), two different functional azo compounds with aliphatic alkyl and carboxy groups, three different functional diacyl peroxides with aliphatic alkyl, aromatic, and carboxy groups, and one peroxydicarbonate with an aliphatic alkyl group. The reaction mechanism was probed using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS). The combination of PBA-I, iodine abstraction catalyst and different functional diacyl peroxides enabled higher chain-end modification to desired moieties from the diacyl peroxide. The dominant key factors for efficiency in this chain-end modification mechanism were the combination rate constant and the amount of radicals generated per unit of time.
Open AccessNovel Chain-End Modification of Polymer Iodides via Reversible Complexation-Mediated Polymerization with Functionalized Radical Generation Agents
The modification of polymer chain ends is important in order to produce highly functional polymers. A novel chain-end modification of polymer iodides (Polymer-I) via reversible complexation-mediated polymerization (RCMP) with different functionalized radical generation agents, such as azo compounds and organic peroxides, was developed. This reaction was comprehensively studied for three different polymers, i.e., poly (methyl methacrylate), polystyrene and poly (n-butyl acrylate) (PBA), two different functional azo compounds with aliphatic alkyl and carboxy groups, three different functional diacyl peroxides with aliphatic alkyl, aromatic, and carboxy groups, and one peroxydicarbonate with an aliphatic alkyl group. The reaction mechanism was probed using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS). The combination of PBA-I, iodine abstraction catalyst and different functional diacyl peroxides enabled higher chain-end modification to desired moieties from the diacyl peroxide. The dominant key factors for efficiency in this chain-end modification mechanism were the combination rate constant and the amount of radicals generated per unit of time.
- Open Access
- 4 December 2022
- Published by Wiley in Advanced Materials Interfaces
- Vol. 10 (5)
Coverage Performance of PEDOT:PSS Against Particles on a Substrate for OLEDs
Short‐circuit defects caused by microscale dust particles in organic light‐emitting diodes (OLEDs) cause a decrease in production yield and hinder cost reduction. An organic layer coating by solution process is used to prevent short‐circuit defects of particles on a substrate. In this study, the coverage properties of a coated organic layer on size‐controlled particles are revealed. The surface of the substrate with size‐controlled SiO2 particles with a diameter of 0.2–5 µm is quantitatively contaminated, and the particle coverage properties of the solution‐processed hole injection layer are investigated. From the results of the leakage current measurement and cross‐sectional observation by a transmission electron microscope, it is observed that devices with 50 nm‐spin‐coated poly (3,4‐ethylenedioxythiophene): poly(styrene sulfonate) can cover SiO2 particles up to 1 µm in diameter without any increase in leakage current. It is revealed that larger‐sized particles cause electric defects, albeit with a low probability, owing to the larger space under the particles. To fabricate OLEDs with a high yield, the shape of the coverage at the bottom of the particle is important in preventing electric defects. The results of this study are useful not only for OLEDs but also for printed and coated devices.
- 4 December 2022
- Published by Wiley in Advanced Materials Interfaces
- Vol. 10 (5)
Open AccessCoverage Performance of PEDOT:PSS Against Particles on a Substrate for OLEDs
Short‐circuit defects caused by microscale dust particles in organic light‐emitting diodes (OLEDs) cause a decrease in production yield and hinder cost reduction. An organic layer coating by solution process is used to prevent short‐circuit defects of particles on a substrate. In this study, the coverage properties of a coated organic layer on size‐controlled particles are revealed. The surface of the substrate with size‐controlled SiO2 particles with a diameter of 0.2–5 µm is quantitatively contaminated, and the particle coverage properties of the solution‐processed hole injection layer are investigated. From the results of the leakage current measurement and cross‐sectional observation by a transmission electron microscope, it is observed that devices with 50 nm‐spin‐coated poly (3,4‐ethylenedioxythiophene): poly(styrene sulfonate) can cover SiO2 particles up to 1 µm in diameter without any increase in leakage current. It is revealed that larger‐sized particles cause electric defects, albeit with a low probability, owing to the larger space under the particles. To fabricate OLEDs with a high yield, the shape of the coverage at the bottom of the particle is important in preventing electric defects. The results of this study are useful not only for OLEDs but also for printed and coated devices.